2001 LAND ROVER FREELANDER fuel

EMISSION CONTROL
17-1-12 REPAIRS
Filter - fuel leak detection pump - KV6 -
NAS
$% 17.45.42
Remove
1.Disconnect battery earth lead.
2.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
3.Remove nut and release filter from bracket.
4.Release clip and remove filter from pipe.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
Refit
1.Fit filter to pipe and secure with clip.
2.Fit filter to bracket and tighten nut to 3 Nm (2.2
lbf.ft).
3.Fit wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
4.Connect battery earth lead.
Catalytic converter - RH - KV6 - NAS
$% 17.50.01
Remove
1.Position vehicle on 4 post ramp.
2.Disconnect battery earth lead.
3.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
4.Release pre catalyst H02S harness from clips.
5.Release and disconnect HO2S multiplug.
6.Remove intermediate pipe and silencer.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Intermediate
pipe - NAS.
7.Remove 3 bolts and remove LH heat shield.
M19 3484

ENGINE MANAGEMENT SYSTEM - SIEMENS
18-3-6 REPAIRS
Engine control module (ECM) - fuel - NAS
$% 18.30.03
Remove
1.Disconnect battery earth lead.
2.Remove 5 Allen screws and 'E' box cover.
3.Disconnect 5 multiplugs from engine ECM.4.Release 2 clips and remove ECM.
Refit
1.Fit ECM and connect multiplugs.
2.Fit 'E' box cover and tighten Allen screws to 2
Nm (1.5 lbf.ft).
3.Connect battery earth lead.
4.Initiate ECM using TestBook/T4.
CAUTION: The ECM can only be re-
programmed a maximum of 20 times.
M18 0665

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-1
FUEL DELIVERY SYST EM - PE TROL ADJUST ME NTS
Throttle cable - check and adjust - KV6
$% 19.20.05
Check
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Before adjusting cable, ensure that cable is
correctly routed and located.
Adjust
1.Release cable adjusting nut from abutment
bracket.2.Hold throttle cam in fully closed position.
3.Rotate adjusting nut until all slack is taken out
of inner cable and nut is in contact with rear
face of abutment bracket. Ensure throttle does
not open.
4.Fit throttle cable adjusting nut in abutment
bracket.
5.Operate throttle pedal and ensure that full
throttle pedal movement is available.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
19-2-2 ADJUSTMENTS
Throttle cable - check and adjust - K1.8
$% 19.20.05
Check
1.Before adjusting cable, ensure that cable is
correctly routed and located.
Adjust
1.Release cable adjusting nut from abutment
bracket.
2.Hold throttle cam in fully closed position.
3.Rotate adjusting nut until all slack is taken out
of inner cable and nut is in contact with rear
face of abutment bracket. Ensure throttle does
not open.
4.Fit throttle cable adjusting nut in abutment
bracket.
5.Operate throttle pedal and ensure that full
throttle pedal movement is available.
Fuel system - depressurise - KV6 - Non
NAS
$% 19.50.02
Check
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
3.Pull back cover from hose connector and
carefully release connector.
WARNING: Depressurise the system before
disconnecting any components. Fuel
pressure will be present in the system even
if the ignition has been switched off for
some time.
4.Secure connector once pressure has been
relieved.
5.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-3
Fuel system - depressurise - KV6 - NAS
$% 19.50.02
Check
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2. Up to 03MY: Remove nut and bolt securing coil
and position coil aside.
3.Remove schraeder valve cap.
4.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.5.Connect adapter LRT-19-006 to schraeder
valve.
6.Position opposite end of adapter LRT-19-006
into container, turn tap to release pressure.
7.Remove adapter LRT-19-006 from schraeder
valve.
8.Fit cap to schraeder valve.
9. Up to 03MY: Fit and tighten nut and bolt
securing coil.
10.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

FUEL DELIVERY SYSTEM - PETROL
19-2-4 ADJUSTMENTS
Fuel system - depressurise - K1.8
$% 19.50.02
Check
1.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
2.Disconnect fuel feed hose from fuel rail.
3.Connect feed hose to fuel rail once pressure
has relieved.
Fuel system - pressure test - KV6 - Non
NAS
$% 19.50.13
Check
1.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth around fuel feed pipe
connection to collect spillage.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
3.Disconnect fuel inlet hose from fuel rail pipe.
4.Connect adaptor LRT-19-013, to pressure
gauge LRT-19-004 .
5.Position pressure gauge LRT-19-004, connect
to fuel inlet hose and to fuel rail pipe, securing
pressure gauge hose to fuel rail pipe with clip.
6.Start engine. Pressure at idle = 3.4 bar. If
pressure below 3.4 bar suspect the following in
order: fuel hoses, filter, regulator and pump.
7.Stop engine.
8.Release clip and disconnect LRT-19-004
pressure gauge from fuel inlet hose and fuel rail
pipe.
9.Disconnect adaptor LRT-19-013 from LRT-19-
004 pressure gauge.
10.Connect fuel inlet hose to fuel rail pipe.
11.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
M19 3247A
LRT-19 - 013
LRT -19- 004

FUEL DELIVERY SYSTEM - PETROL
ADJUSTMENTS 19-2-5
Fuel system - pressure test - KV6 - NAS
$% 19.50.13
Remove
1.Remove acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
2.Position absorbent cloth beneath fuel rail.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
3. Up to 03MY: Remove nut and bolt securing coil
and position coil aside.
4.Connect adaptor LRT-19-006, to pressure
gauge LRT-19-004 .
5.Remove schraeder valve cap.
6.Connect pressure gauge to fuel rail schraeder
valve.
7.Start engine. Pressure at idle = 3.4 bar. If
pressure is below 3.4 bar, suspect the following
in order: fuel hoses, filter, regulator and pump.
Refit
1.Stop engine.
2.Disconnect pressure gauge LRT-19-006 and
adapter LRT-19-004 from fuel rail.
3. Up to 03MY: Fit and tighten nut and bolt
securing coil.
4.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
Fuel system - pressure test - K1.8
$% 19.50.13
Check
1.Disconnect battery earth lead.
2.Position absorbent cloth beneath fuel pipe to
catch spillage.
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
3.Disconnect fuel pipe from inlet manifold.
4.Connect LRT-19-004A to manifold and fuel
pipe.
Note:: LRT-19-004X can be used as an
alternative.
5.Connect battery earth lead.
6.Start engine. Pressure at idle = 3.6 bar ± 0.2
bar.
7.Stop engine. If pressure is out of tolerance
suspect the following in order: fuel hoses, filter
and pump.
8.Remove plug, reconnect vacuum hose and
secure hose with clip.
9.Disconnect battery earth lead.
10.Disconnect LRT-19-004A from fuel pipe and
inlet manifold.
11.Connect fuel pipe to manifold.
12.Connect battery earth lead.
LRT - 19 -004A
M19 3675

FUEL DELIVERY SYSTEM - PETROL
19-2-6 ADJUSTMENTS
Fuel tank - drain
$% 19.55.02
Drain
1.Disconnect both battery leads, negative lead
first.
2.Remove fuel pump assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Pump - fuel.
3.Using a fuel recovery appliance, drain the fuel
from the tank into a sealed container. Follow
the manufacturer's instructions for the
connection and safe use of the appliance.
WARNING: Fuel vapour is highly flammable
and in confined spaces is also explosive
and toxic. Always have a fire extinguisher
containing foam, CO
2, gas or powder close
at hand when handling or draining fuel.
Refill
1.Fit fuel pump assembly.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Pump - fuel.
2.Connect battery leads, earth lead last.