Page 146 of 1007

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-3
Lubrication
The engine and other lubricating systems are filled
with high- performance lubricants giving prolonged
life.
CAUTION: Always use a high quality oil of the
correct viscosity range in the engine. The use of
oil of the incorrect specification can lead to high
oil and fuel consumption and ultimately to
damaged components.
Oil to the correct specification contains additives
which disperse the corrosive acids formed by
combustion and prevent the formation of sludge
which can block the oil ways. Additional oil additives
should not be used.
Always adhere to the recommended servicing
intervals.
Engine oil
Engine oil viscosity / temperature ranges are
indicated in the following table:
a0W/30; 5W/30
b0W/40, 50, 60; 5W/40, 50, 60
c10W/30
d10W/40, 50, 60
Engine oil – Td4 engine
Use 0W/30 or 5W/40, 50, 10W/30, 40, 60 oil meeting
ACEA A3/B3 specifications, and having a viscosity
band recommended for the temperature range of
your locality. Where oils to these European
specifications are not available, well known brands of
oils meeting API SH quality should be used.Engine oil – K1.8 engine
Use a 10W/40 oil meeting specification ACEA A2 or
A3.
Engine oil – KV6 engine – Non NAS models
Use a 10W/40 oil meeting specification ACEA A2 or
A3.
Engine oil – KV6 engine - NAS models
Use a 5W/40 fully synthetic oil meeting specification
ACEA A3. Where oils to these European
specifications are not available, well known brands of
oils meeting API SH quality should be used.
Gearbox oil
Use of gearbox oils other than those specified may
result in serious damage to the gearbox.
Manual Gearbox – PG1 and Getrag
Use OPEL B 0400063 for refill or topping-up.
Automatic Gearbox – JATCO
Use Texaco N402 fluid for refill or topping-up.
Intermediate Reduction Drive
Texaco S5 75W90; Synthetic oil or equivalent,
meeting: API GL5
Rear Differential
Multigear 80W/90 ETL; Specification: API GL5
Gear linkage - Manual
Use grease containing 3% Molybdenum Disulphide.
General Greasing
Use Multipurpose Lithium Base Grease NLGI
consistency No. 2.
Bonnet latch
Lubricate cable and latch with oil.
Page 147 of 1007

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-4
Sealants
The following table lists those sealants which are
used during repair / overhaul procedures covered in
this manual; it is essential that the sealant specified
for a particular procedure is used at all times.
Component Application Land Rover
Part No.
Td4 Engine Camshaft cover
gasket joint linesSTC 50550
Td4 Engine Sump gasket joint
linesSTC 50550
K 1.8 Engine Oil pressure switch
threadsSTC 50552
K 1.8 Engine Oil pressure relief
valve plug threadsSTC 50552
K 1.8 Engine Oil temperature
sensor threadsSTC 50552
K 1.8 Engine Oil pump cover
plate screwsSTC 50552
K 1.8 Engine Camshaft carrier to
cylinder headSTC 4600
K 1.8 Engine Bearing ladder to
cylinder blockSTC 4600
K 1.8 Engine Sump to bearing
ladderSTC 4600
K 1.8 Engine Oil rail to bearing
ladderSTC 4600
K 1.8 Engine Crankshaft rear oil
seal STC 50550
K 1.8 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Camshaft timing
belt backplate
cover boltsSTC 50552
KV6 Engine Oil pressure relief
valve plug threadsSTC 50552
KV6 Engine Oil pump cover
plate screwsSTC 50552
KV6 Engine Camshaft carrier to
cylinder headSTC 4600
KV6 Engine Sump to lower
crankcaseSTC 4600
KV6 Engine Oil pick-up strainer
boltSTC 50552
KV6 Engine Lower crankcase to
cylinder blockSTC 50550
KV6 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Coolant stub pipe to
cylinder blockSTC 50554
Engine
Management
System -
MEMSSensor - Engine
Coolant
temperature (ECT)STC 50552
Cooling
System - KV6Cylinder block drain
plugSTC 50552
Manual
Gearbox - PG12 top bolts -
gearbox to engineSTC 50552
Manual
Gearbox -
GetragRear cover to
gearcaseSTC 4600
Manual
Gearbox -
GetragGearshift cover STC 4600
Intermediate
Reduction
DriveEnd cover gasket -
IRD housingSTC 4600
Automatic
Gearbox -
JatcoFluid pan to
gearcaseSTC 4600
Rear Axle and
Final DriveDifferential cover to
casingSTC 3811
Page 166 of 1007

MAINTENANCE
MAINTENANCE 10-19
Manual Gearbox – GETRAG
Replace Fluid
WARNING: Avoid excessive skin contact
with mineral oil. Mineral oils remove the
natural fats from the skin, leading to
dryness, irritation and dermatitis.
1.Replace gearbox fluid.
+ MANUAL GEARBOX - GETRAG,
ADJUSTMENTS, Gearbox oil - drain and
refill.
Automatic Gearbox – JATCO
Check and top-up fluid
WARNING: Avoid excessive skin contact
with mineral oil. Mineral oils remove the
natural fats from the skin, leading to
dryness, irritation and dermatitis.
1.Position vehicle on ramp.
2.Apply handbrake and position chocks under
front and rear wheels.
3.Remove underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Connect TestBook/T4 to monitor gearbox fluid
temperature.
CAUTION: The gearbox fluid level must only
be checked when the temperature of the
fluid is between 35° and 45°. The reading
obtained will be incorrect if the fluid is
outside this temperature range.
5.Start engine, move selector lever from 'P'
through all gear positions, pausing in each gear
position for 2-3 seconds and return to 'P'
position.
6.Clean area around level plug.
7.With the engine still running, remove level plug
using a 5 mm Allen socket and allow any
excess fluid to drain off.
CAUTION: There are a number of similar
fixings/plugs on the underside of the
gearbox. It is imperative that the correct
plug is removed prior to checking the level.
Removing the wrong fixing/plug could
result in internal damage to the gearbox.
8.If no fluid loss is apparent when level plug is
removed:
Page 167 of 1007

MAINTENANCE
10-20 MAINTENANCE
9.Remove filler plug and add fluid until it just runs
from level plug aperture.
When topping up after a new air blast cooler
(Td4 hot climates) has been fitted, an extra
420 cc of fluid is required. The fluid must
also reach a temperature of 80° C (176° F) to
allow the switch on the cooler to open.
10.Move selector lever from 'P' through each gear
position and return to 'P' , allowing any excess
fluid to drain off.
11.Fit new level plug and tighten to 14 Nm (10
lbf.ft).
12.Clean and fit filler plug.
13.Disconnect TestBook/T4.
14.Fit underbelly panel.
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
Rear Axle
Replace Fluid
1.With vehicle on a ramp at a convenient working
height, carefully remove rear differential level
plug.
2.Check oil level. Before topping up oil level,
check for visible signs of leakage. Pay
particular attention to drive shaft oil seals,
differential pinion oil seal and backplate
gasket.
3.Refit level plug to rear differential and tighten to
27 Nm (20 lbf.ft).
M44 1642
Page 178 of 1007
ENGINE - K SERIES KV6
ADJUSTMENTS 12-3-1
ENGIN E - K SERIES KV6 ADJUST ME NTS
Engine oil pressure check
$% 12.90.09.01
Check
1.Remove oil pressure switch.
+ ENGINE - K SERIES KV6, REPAIRS,
Switch - oil pressure.
2.Fit sealing washer from oil pressure switch to
LRT-12-052/10 oil pressure gauge adaptor.
3.Fit and tighten oil pressure gauge adaptor LRT-
12-052/10 to oil pump housing.
4.Connect oil pressure gauge LRT-12-052C and
tighten union.
5.Check and if necessary top up engine oil.
6.Start and run engine until normal operating
temperature is reached.
7.Note oil pressure readings with the engine
running at idle and at 3000 rev/min.
+ GENERAL DATA, Engine - KV6
Petrol.
8.Switch off engine, unscrew gauge union and
remove gauge.
9.Remove adaptor.
10.Wipe off oil spillage
11.Fit oil pressure switch.
+ ENGINE - K SERIES KV6, REPAIRS,
Switch - oil pressure.
12.Recheck engine oil and top up if necessary.
Page 405 of 1007

INTERMEDIATE REDUCTION DRIVE
41-2 ADJUSTMENTS
Intermediate reduction drive (IRD)
lubrication system - drain & refill - NAS
$% 41.25.06
Drain
1.Remove underbelly panel
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
2.Place container beneath IRD unit.
WARNING: Observe due care when draining
gearbox fluid as the fluid can be very hot.
3.Clean area around filler/level and drain plugs.
4.Using LRT-41-021 remove filler plug and
discard sealing washer.5.Remove drain plug, discard sealing washer and
allow oil to drain.
NOTE: The fluid should be drained with the
transmission at normal operating temperature.
6.Fit new sealing washer and tighten drain plug to
35 Nm (26 lbf.ft).
Refill
1.Fill with fluid until it just runs from filler/level
hole. Allow sufficient time for fluid to flow and
reach a common level in unit.
+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
2.Fit new sealing washer and tighten filler/level
plug to 35 Nm (26 lbf.ft).
3.Fit underbelly panel
+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
M417853
LRT-41-021
M41 7687