Page 736 of 1007
BODY DIMENSIONS
BODY DIMENSIONS 77-1-1
BODY DIMENSIONS BODY DIMENSIONS
Dimensional Information
Measurement Types
The following dimensional information is shown so as to assist the technician in the diagnosis and repair of body
panels. The information is shown in two different ways. There are X,Y,Z dimensions and actual point to point
dimensions.
The X,Y,Z dimensions are the measuring planes used within Land Rover for the measurement of body panels. The
whole bodyshell is within a parallel grid system, see illustrations below.
The X plane is an imaginary vertical plane starting at the front of the vehicle. It is at right angles to the centre line of
the vehicle and measures distances along the length of the vehicle.
The Y plane is an imaginary plane through the centre of the vehicle. All Y dimensions start from this plane. As a rule,
body dimensions are symmetrical about the centre line.
The Z plane is set at a fixed distance parallel to the underside of the vehicle. All Z dimensions start from this plane.
The point to point measurements are actual distances between two points. These points can be holes or intersection
points. Where holes are taken, the point of measurement is always from the hole centre.
Measurements shown are in millimetres and inches. The measurements shown in brackets are in inches.
The tolerance for the basic geometry of the vehicle is ± 1.0 mm (0.040). This includes tooling holes, all fixing holes
and apertures.
The tolerance for matching panel form and break lines is ± 0.5 mm (0.020).
Page 737 of 1007
BODY DIMENSIONS
77-1-2 BODY DIMENSIONS
Page 738 of 1007
BODY DIMENSIONS
BODY DIMENSIONS 77-1-3
Dimensional Illustrations
X,Y,Z Dimensional Information
Front end dimensional information
No. Description X Y Z
1 Front damper large hole 977 (38.464) 578.5 (22.775) 718.5 (28.287)
2 Front damper, inboard fixing hole 975.4 (38.401) 514.9 (20.271) 693.7 (27.311)
3 Wing, front fixing 605 (23.818) 669 (26.338) 806 (31.732)
4 Wing, rear fixing, 1220 (48.031) 690 (27.165) 848.2 (33.393)
5 Outboard headlamp fixing hole 465 (18.307) 615 (24.212) 788 (31.023)
6 Inboard headlamp fixing hole 377 (14.842) 485 (19.094) 772 (30.393)
7 Bonnet locking platform, jig location hole 390 (15.354) 445 (17.519) 765 (30.118)
8 Sidemember, jig location hole 500 (19.685) 446 (17.559) 388 (15.275)
9 Headlamp mounting panel, jig location hole 239 (9.409) 536 (21.102) 335 (13.188)
10 Front valance, jig location hole 540 (21.259) 671.7 (26.444) 525 (20.669)
Page 739 of 1007
BODY DIMENSIONS
77-1-4 BODY DIMENSIONS
Underbody dimensional information
Page 740 of 1007
BODY DIMENSIONS
BODY DIMENSIONS 77-1-5
No. Description X Y Z
1 Front sidemember, jig location hole 420 (16.534) 481 (18.937) 312 (12.283)
2 Front crossmember, jig location hole 340.5 (13.405) 350 (13.779) 154.4 (6.062)
3 Front damper, inboard fixing hole 975.5 (38.405) 515 (20.275) 693.5 (27.303)
4 Front subframe, front fixing 1036 (40.787) 386 (15.196) 98 (3.858)
5 Front subframe, rear outboard fixing 1326 (52.204) 429.5 (16.909) 127 (5.0)
6 Front subframe, rear inboard fixing 1326 (52.204) 330 (12.992) 127 (5.0)
7 Outrigger panel, jig location hole 1395 (54.921) 535 (21.062) 125 (4.921)
8 Link arm fixing, centre hole 2765 (108.858) 463 (18.228) 160 (6.299)
9 Rear longitudinal front, jig location hole 2900 (114.173) 432 (17.007) 131.5 (5.177)
10 Rear subframe, front mounting hole 3302 (130.0) 465 (18.307) 274.5 (10.807)
11 Spring location, rear fixing hole 3636 (143.149) 610 (24.015) 728.5 (28.681)
12 Rear subframe, rear fixing 3671.5 (144.547) 515 (20.275) 305 (12.007)
13 Rear longitudinal rear, jig location hole 4000 (157.480) 527 (20.748) 305 (12.007)
14 Rear crossmember, jig location hole 4122.5 (162.303) 410 (16.141) 301 (11.850)
Page 741 of 1007
BODY DIMENSIONS
77-1-6 BODY DIMENSIONS
Under body information
Item From To Length
A Front crossmember, jig location hole Front subframe, rear mounting hole 1197.3 (47.137)
B Front crossmember, jig location hole Front subframe, rear mounting hole 985.7 (38.807)
C Front Subframe, front mounting hole `LH` Front subframe, front mounting hole `RH` 772.0 (30.393)
D Front subframe, front mounting hole Front subframe, rear mounting hole 295.3 (11.625)
E Front subframe, front mounting hole Front subframe, rear mounting hole 772.5 (30.413)
F Front subframe, rear mounting hole `RH` Front subframe rear mounting hole `LH` 660.0 (25.984)
G Front subframe, rear mounting hole Rear longitudinal front, jig location hole 1577.3 (62.098)
H Front subframe, rear mounting hole Rear subframe, front mounting hole 2129.9 (83.854)
J Rear longitudinal front, jig location hole Rear subframe, front mounting hole 983.0 (38.700)
K Rear subframe, front mounting hole `LH` Rear subframe front mounting hole `RH` 930.0 (36.614)
L Rear longitudinal front, jig location hole Rear subframe, front mounting hole 403.4 (15.881)
M Rear subframe, front mounting hole Rear crossmember, jig location hole 822.3 (32.374)
N Rear subframe, front mounting hole Rear crossmember, jig location hole 1199.5 (47.224)
Page 742 of 1007
BODY DIMENSIONS
BODY DIMENSIONS 77-1-7
Under body information
Item From To Length
A Sidemember, forward jig location hole `LH` Sidemember, forward jig location hole `RH` 962 (37.874
B Sidemember, forward jig location hole Front subframe, rear mounting hole 1216.0 (47.874
C Spring location, inboard fixing hole `LH` Spring location, inboard fixing hole `RH` 1029.8 (40.543)
D Spring location, inboard fixing hole Front subframe, rear mounting hole 396.4 (15.606)
E Spring location, inboard fixing hole Front subframe, rear mounting hole 914.8 (36.015)
F Link arm fix, `LH` Link arm fix, `RH` 926.2 (36.464)
G Rear longitudinal front, jig location hole Rear subframe, front mounting hole 403 (15.866)
H Link arm fix Rear subframe, front mounting hole 1072.2 (42.212)
J Rear subframe, front mounting hole Spring location, rear hole 364.2 (14.338)
K Rear subframe, front mounting hole Spring location, rear fixing hole 1125.7 (44.318)
L Rear subframe, front mounting hole Rear longitudinal rear, jig location hole 1213.0 (47.755
M Spring location, rear fixing hole `LH` Spring location, rear fixing hole `RH` 1220.0 (48.031
N Rear subframe, front mounting hole Rear longitudinal rear, jig location hole 700.7 (27.586)
P Rear longitudinal rear, jig location hole `LH` Rear longitudinal rear, jig location hole `RH` 1054.0 (41.496)
Page 743 of 1007
BODY DIMENSIONS
77-1-8 BODY DIMENSIONS
Under body information
Item From To Length
A Link arm fix, `LH` Link arm fix, `RH` 926.2 (36.464)
B Rear crossmember, jig location hole `LH` Rear crossmember, jig location hole `RH` 820 (32.283)
C Rear subframe, front mounting hole `LH` Rear subframe, front mounting hole `RH` 930 (36.614)
D Rear subframe, rear mounting hole `LH` Rear Subframe, rear mounting hole `RH 1030 (40.551)
E Spring location, rear fixing hole `LH` Spring location, rear fixing hole `RH` 1219.9 (48.027)
F Link arm fix Rear subframe, rear mounting hole 906.7 (35.696)
G Rear Subframe, front mounting hole Rear subframe, rear mounting hole 369.7 (14.555)
H Rear subframe, rear mounting hole Rear crossmember, jig location hole 450.8 (17.748)
J Zero `Z` datum Link arm fix 160 (6.299)
K Zero `Z` datum Rear longitudinal rear, jig location hole 272.8(10.740)
L Zero `Z` datum Rear crossmember, jig location hole 299.5 (11.791)
M Zero `Z` datum Rear longitudinal rear, jig location hole 303.5 (11.948)
N Zero `Z` datum Spring location, rear fixing hole 728.5 (28.681)
