2001 LAND ROVER FREELANDER ECU

ENGINE - K SERIES KV6
12-3-108 OVERHAUL
4.Remove Torx screw securing idler pulley to
front mounting plate and remove pulley.
5.Release alternator battery lead terminal cover,
loosen terminal nut and disconnect lead from
terminal
6.Disconnect multiplug from alternator.
7.Remove lower bolt and upper nut and bolt
securing alternator to front mounting plate.
8.Release alternator and remove.9.Remove 3 bolts securing camshaft timing belt
LH rear cover and remove cover.
10.Remove inlet manifold chamber - if fitted.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
11.Remove 2 bolts securing RH rear timing belt
cover heat shield to cylinder head; remove heat
shield.
12.Remove 3 bolts securing RH rear timing belt
cover; remove cover.
M12 6694

ENGINE - K SERIES KV6
OVERHAUL 12-3-109
13.Using a socket on crankshaft pulley bolt, rotate
crankshaft in a clockwise direction and align the
engine "SAFE" position - notch on crankshaft
pulley aligned to the "ARROW" on front
mounting plate. Check that the timing marks on
the rear camshaft gears are aligned as
illustrated.
CAUTION: Do not use the camshaft gear
bolts or timing belts to rotate the
crankshaft. Do not use the arrow on the oil
pump body as a timing reference.
14.Insert timing pin LRT-12-232 through hole
immediately adjacent to side of lower
crankcase ensuring that pin is located in hole in
drive plate.15.Remove 3 bolts securing camshaft timing belt
LH front cover and remove cover.
16.Remove 3 bolts securing camshaft timing belt
RH front cover and remove cover.
17.Remove bolt securing dipstick tube to cylinder
block.
18.Depress locking collar, release and remove
dipstick tube from engine sump.
LRT-12-232
M12 7927
M12 6672

ENGINE - K SERIES KV6
12-3-110 OVERHAUL
19.Assemble LRT-12-161 to LRT-12-199 and
secure with clamp bolt.
20.Insert LRT-12-161 with LRT-12-199 into
crankshaft pulley, loosen and remove pulley
bolt.
CAUTION: Ensure crankshaft does not
rotate during above operation.
21.Remove LRT-12-161 and LRT-12-199 from
crankshaft pulley.
22.Remove crankshaft pulley.
23.Remove 3 bolts securing camshaft timing belt
lower cover to cylinder block and remove cover.24.Remove 3 bolts securing engine front mounting
plate and lifting bracket to cylinder block.
25.Remove bolt securing lifting bracket to RH
cylinder head and remove lifting bracket.
26.Remove rubber blanking plug from around
camshaft timing belt tensioner.

ENGINE - K SERIES KV6
OVERHAUL 12-3-111
27.Remove 5 bolts and 2 pillar bolts securing
engine front mounting plate to cylinder block.
28.Remove 2 bolts securing IRD support bracket
to engine front mounting plate.
29.With care, release and remove front mounting
plate from engine.
30.Fit a suitable 1.5 mm diameter pin through hole
in tensioner body and into hole in plunger.
NOTE: If holes in body and plunger are not
aligned, move tensioner backplate using a
broad bladed screwdriver; this will move the
plunger sufficiently to align the holes and allow
the pin to be inserted.31.Remove and discard 2 Patchlok bolts securing
tensioner to cylinder block and remove
tensioner.
CAUTION: Exercise great care when
removing bolts, do not apply excessive
torque. If bolts appear to be seized, apply
suitable anti-seize lubricant prior to
removing bolts. DO NOT loosen Allen screw
securing tensioner pulley.
32.If camshaft timing belt is to be refitted, mark
direction of rotation on timing belt before
removal.
33.With care, ease camshaft timing belt from
gears using fingers only and remove timing
belt.
CAUTION: Do not rotate crankshaft or
camshafts with timing belt removed.
CAUTION: Camshaft timing belt must be
replaced if cylinder head is to be removed or
new drive gears, tensioner or coolant pump
are to be fitted. Camshaft timing belts must
be stored and handled with care. Always
store a camshaft timing belt on its edge with
a bend radius greater than 50 mm (2.0 in).
Do not use a camshaft timing belt that has
been twisted or bent double as this will
damage the reinforcing fibres. Do not use a
camshaft timing belt if debris other than belt
dust is found in timing belt covers. Do not
use a camshaft timing belt if partial engine
seizure has occurred. Do not use a
camshaft timing belt if mileage exceeds
72,000 km (45,000 miles). Do not use an oil
or coolant contaminated timing belt, cause
of contamination must be rectified.
34.Remove and discard LH and RH exhaust
camshaft cap seals.

ENGINE - K SERIES KV6
OVERHAUL 12-3-113
11.Position an Allen key in tensioner backplate
and hold tensioner pulley against timing belt.
12.With assistance, position timing belt tensioner,
fit new Patchlok bolts and tighten to 25 Nm (18
lbf.ft).
CAUTION: Ensure tensioner plunger is
contacting underside of tensioner
backplate.
13.Remove tools LRT-12-175 from rear timing belt
gears.
14.Fit tools LRT-12-196 to both front inlet
camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
15.Tighten front inlet camshaft gear bolts to:
lStage 1 - 27 Nm (20 lbf.ft)
lStage 2 - Further 90°
16.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.17.Remove wedge from between drive belt and oil
pump belt guard.
18.Remove 1.5 mm diameter pin from tensioner.
19.Clean exhaust camshaft front cap seal
locations and fit new cap seals.
CAUTION: The sealing edge of the cap seal
and mating face must be clean and dry.
20.Position engine front mounting plate and
manoeuvre plate into position; fit bolts but do
not tighten at this stage.
21.Fit bolts securing IRD support bracket to front
mounting plate; do not tighten bolts at this
stage.
22.Tighten bolts in the sequence shown:
lM10 bolt - No.1 - 25 Nm (18 lbf.ft)
lM10 bolt - No. 5 - 45 Nm (33 lbf.ft)
lBolts Nos. 2, 3, 4, 6 and 7 - 85 Nm (63 lbf.ft)
23.Position engine lifting bracket, fit bolts securing
lifting bracket and front mounting plate to
cylinder block and RH cylinder head and
tighten to:
lM8 bolt - 25 Nm (18 lbf.ft)
lM10 bolts - 45 Nm (33 lbf.ft)
24.Fit rubber blanking plug around tensioner.
25.Clean end of dipstick tube.
26.Position dipstick tube to sump and cylinder
block, fit bolt and tighten to 9 Nm (7 lbf.ft).
27.Clean lower timing belt cover.
28.Position lower timing belt cover, fit and tighten
bolts to 9 Nm (7 lbf.ft).
29.Remove timing pin LRT-12-232.
30.Clean crankshaft pulley.
31.Fit crankshaft pulley to crankshaft gear and
ensure that the indent on pulley locates over
the lug on crankshaft gear.
32.Fit crankshaft pulley bolt and washer, position
LRT-12-161 with LRT-12-199 into crankshaft
pulley. Tighten pulley bolt to 160 Nm (118
lbf.ft).
33.Remove tools LRT-12-161 and LRT-12-199.
34.Clean ancillary drive belt tensioner.

ENGINE - K SERIES KV6
12-3-114 OVERHAUL
35.Position ancillary belt tensioner, fit bolts and
tighten to 25 Nm (18 lbf.ft).
36.Clean LH and RH front timing belt covers.
37.Position LH and RH front timing belt covers, fit
and tighten bolts to 4 Nm (3 lbf.ft).
38.Clean idler pulley, position pulley to engine
front mounting plate and tighten Torx bolt to 45
Nm (33 lbf.ft).
39.Position alternator to front mounting plate.
40.Fit bolt and nut and bolt securing alternator to
front mounting plate and tighten to 45 Nm (33
lbf.ft).
41.Connect alternator multiplug.
42.Connect battery lead to alternator, fit and
tighten nut to 8 Nm (6 lbf.ft), fit terminal cover.
43.Clean LH rear timing belt cover.
44.Position LH rear timing belt cover, fit and
tighten bolts to 4 Nm (3 lbf.ft).
45.Clean RH rear timing belt cover.
46.Position RH rear timing belt cover, fit bolts and
tighten to 4 Nm (3 lbf.ft).
47.Position heat shield, fit bolts and tighten M6 bolt
to 9 Nm (7 lbf.ft) and M8 bolt to 25 Nm (18 lbf.ft).
48.Fit inlet manifold chamber - if fitted.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
49.Position ancillary drive belt to crankshaft and
alternator pulleys.
50.Position engine mounting front bracket to
engine front plate and tighten bolts to 45 Nm
(33 lbf.ft).

EMISSION CONTROL
ADJUSTMENTS 17-1-1
EMISS ION CONTROL ADJUST ME NTS
Evaporative loss control system
(EVAPS) - leak test - NAS
$% 17.90.02.01
The following procedure allows a fuel leak, indicated
by the Malfunction Indicator Lamp (MIL), to be
accurately located. It must only be carried out once it
has been established that there are no obvious faults
with any of the system components.
Check
1.Check components in fuel and EVAP system
for obvious damage. Ensure all connections
are properly secured.
2.The system must be checked using a EVAPS
Diagnostic Testing Station LRA-19-004.
3.Disconnect vent pipe from purge valve and
connect adapter LRA-19-004/1.
NOTE: The reason for inserting the adapter into
the purge valve is that there is currently no
service port fitted to Freelander.
4.Remove RH rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
5.Release clip and disconnect hose from
charcoal canister.
CAUTION: Before disconnecting any part of
the fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign
matter into fuel system.
6.Block charcoal canister port with bung,
included in LRA-19-004.
7.Connect LRA-19-004 to service port fitted on
purge valve.
8.Carry out procedures given in the operating
instructions, these are supplied with LRA-19-
004.Adjust
1.If a leak has been detected, replace component
as necessary and repeat leak test to validate
repair.
2.Remove bung from charcoal canister.
3.Connect hose to charcoal canister and secure
with clip.
4.Fit rear wheel arch liner.

+ EXTERIOR FITTINGS, REPAIRS,
Liner - rear wheel arch.
5.Disconnect adaptor LRA-19-004/1 from purge
valve.
6.Connect hose to purge valve.

EMISSION CONTROL
REPAIRS 17-1-3
REPAIRS
Valve - depression limiter - Td4
$% 17.10.25
Remove
1.Disconnect battery earth lead.
2.Remove air cleaner element

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
3.Disconnect multiplugs from injectors.
4.Remove 3 screws and move injector harness
aside.
5.Remove 4 Allen screws and remove valve with
filter assembly. Discard seals.Refit
1.Clean filter with valve housing and mating
faces.
2.Use new seals, fit filter and valve assembly,
tighten Allen screws to 8 Nm (6 lbf.ft).
3.Position injector harness and secure with
screws.
4.Connect multiplugs to injectors.
5.Fit air cleaner element.
+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
6.Connect battery earth lead.
M17 0280
M17 0281