2001 INFINITI QX4 engine

SAT017K
HOW TO ERASE DTC (WITH GST)NBAT0016S041. If the ignition switch stays ªONº after repair work, be sure to turn ignition switch ªOFFº once. Wait at least
5 seconds and then turn it ªONº (engine stopped) again.
2. Perform ªOBD-II SELF-DIAGNOSTIC PROCEDURE (No Tools)º. Refer to AT-46. (The engine warm-up
step can be skipped when performing the diagnosis only to erase the DTC.)
3. Select Mode 4 with Generic Scan Tool (GST). For details, refer to EC-95, ªDESCRIPTIONº.
HOW TO ERASE DTC (NO TOOLS)NBAT0016S051. If the ignition switch stays ªONº after repair work, be sure to turn ignition switch ªOFFº once. Wait at least
5 seconds and then turn it ªONº (engine stopped) again.
2. Perform ªTCM SELF-DIAGNOSTIC PROCEDURE (No Tools)º. Refer to AT-46. (The engine warm-up step
can be skipped when performing the diagnosis only to erase the DTC.)
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
OBD-II Diagnostic Trouble Code (DTC) (Cont'd)
AT-36

SAT964I
Malfunction Indicator Lamp (MIL)=NBAT0183The MIL is located on the instrument panel.
1. The MIL will light up when the ignition switch is turned ON
without the engine running. This is a bulb check.
IIf the MIL does not light up, refer to EL-114, ªSchematicº.
(Or refer to EC-648, ªWiring Diagramº.)
2. When the engine is started, the MIL should go off.
If the MIL remains on, the on board diagnostic system has
detected an engine system malfunction. For detail, refer to
EC-59, ªIntroductionº.
CONSULT-IINBAT0184After performing ªSELF-DIAGNOSTIC PROCEDURE (WITH CON-
SULT-II)º (AT-37), place check marks for results on the ªDIAGNOS-
TIC WORKSHEETº, AT-55. Reference pages are provided follow-
ing the items.
NOTICE:
1) The CONSULT-II electrically displays shift timing and lock-up
timing (that is, operation timing of each solenoid).
Check for time difference between actual shift timing and the
CONSULT-II display. If the difference is noticeable, mechani-
cal parts (except solenoids, sensors, etc.) may be malfunction-
ing. Check mechanical parts using applicable diagnostic pro-
cedures.
2) Shift schedule (which implies gear position) displayed on
CONSULT-II and that indicated in Service Manual may differ
slightly. This occurs because of the following reasons:
IActual shift schedule has more or less tolerance or allowance,
IShift schedule indicated in Service Manual refers to the point
where shifts start, and
IGear position displayed on CONSULT-II indicates the point
where shifts are completed.
3) Shift solenoid valve ªAº or ªBº is displayed on CONSULT-II at
the start of shifting. Gear position is displayed upon completion
of shifting (which is computed by TCM).
4) Additional CONSULT-II information can be found in the Opera-
tion Manual supplied with the CONSULT-II unit.
SAT014K
SELF-DIAGNOSTIC PROCEDURE (WITH CONSULT-II)NBAT0184S011. Turn on CONSULT-II and touch ªENGINEº for OBD-II detected
items or touch ªA/Tº for TCM self-diagnosis.
If A/T is not displayed, check TCM power supply and ground
circuit. Refer to AT-92. If result is NG, refer to EL-9, ªSche-
maticº.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Malfunction Indicator Lamp (MIL)
AT-37

SAT987J
2. Touch ªSELF-DIAG RESULTSº.
Display shows malfunction experienced since the last erasing
operation.
CONSULT-II performs REAL-TIME SELF-DIAGNOSIS.
Also, any malfunction detected while in this mode will be dis-
played at real time.
SELF-DIAGNOSTIC RESULT TEST MODENBAT0184S02
Detected items
(Screen terms for CONSULT-II, ªSELF-DIAG
RESULTSº test mode)
Malfunction is detected when ...TCM self-diagnosis OBD-II (DTC)
Available by
O/D OFF
indicator lamp or
ªA/Tº on CONSULT-IIAvailable by
malfunction
indicator lamp*2,
ªENGINEº on CON-
SULT-II or GST ªA/Tº ªENGINEº
PNP switch circuitITCM does not receive the cor-
rect voltage signal (based on
the gear position) from the
switch.Ð P0705
ÐPNP SW/CIRC
Revolution sensorITCM does not receive the
proper voltage signal from the
sensor.X P0720
VHCL SPEED
SEN´A/TVEH SPD SEN/CIR
AT
Vehicle speed sensor (Meter)ITCM does not receive the
proper voltage signal from the
sensor.XÐ
VHCL SPEED
SEN´MTRÐ
A/T 1st gear functionIA/T cannot be shifted to the 1st
gear position even if electrical
circuit is good.Ð P0731*1
ÐA/T 1ST GR FNCTN
A/T 2nd gear functionIA/T cannot be shifted to the 2nd
gear position even if electrical
circuit is good.Ð P0732*1
ÐA/T 2ND GR FNCTN
A/T 3rd gear functionIA/T cannot be shifted to the 3rd
gear position even if electrical
circuit is good.Ð P0733*1
ÐA/T 3RD GR FNCTN
A/T 4th gear functionIA/T cannot be shifted to the 4th
gear position even if electrical
circuit is good.Ð P0734*1
ÐA/T 4TH GR FNCTN
A/T TCC S/V function (lock-up)IA/T cannot perform lock-up
even if electrical circuit is good.Ð P0744*1
Ð A/T TCC S/V FNCTN
Shift solenoid valve AITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P0750
SHIFT SOLENOID/V
ASFT SOL A/CIRC
Shift solenoid valve BITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P0755
SHIFT SOLENOID/V
BSFT SOL B/CIRC
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont'd)
AT-38

Detected items
(Screen terms for CONSULT-II, ªSELF-DIAG
RESULTSº test mode)
Malfunction is detected when ...TCM self-diagnosis OBD-II (DTC)
Available by
O/D OFF
indicator lamp or
ªA/Tº on CONSULT-IIAvailable by
malfunction
indicator lamp*2,
ªENGINEº on CON-
SULT-II or GST ªA/Tº ªENGINEº
Overrun clutch solenoid valveITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P1760
OVERRUN CLUTCH
S/VO/R CLUCH SOL/
CIRC
T/C clutch solenoid valveITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P0740
T/C CLUTCH SOL/V TCC SOLENOID/
CIRC
Line pressure solenoid valveITCM detects an improper volt-
age drop when it tries to operate
the solenoid valve.X P0745
LINE PRESSURE
S/VL/PRESS SOL/CIRC
Throttle position sensor
Throttle position switchITCM receives an excessively
low or high voltage from the
sensor.X P1705
THROTTLE POSI
SENTP SEN/CIRC A/T
Engine speed signalITCM does not receive the
proper voltage signal from the
ECM.X P0725
ENGINE SPEED SIG
A/T fluid temperature sensorITCM receives an excessively
low or high voltage from the
sensor.X P0710
BATT/FLUID TEMP
SENATF TEMP SEN/
CIRC
Engine controlIThe ECM-AT communication
line is open or shorted.X EC-440, EC-603
A/T COMM LINE Ð
Turbine revolution sensorITCM does not receive the
proper voltage signal from the
sensor.XÐ
TURBINE REV
Ð
TCM (RAM)ITCM memory (RAM) is malfunc-
tioning.
ÐÐ
CONTROL UNIT
(RAM)Ð
TCM (ROM)ITCM memory (ROM) is malfunc-
tioning.
ÐÐ
CONTROL UNIT
(ROM)Ð
TCM (EEP ROM)ITCM memory (EEP ROM) is
malfunctioning.
ÐÐ
CONTROL UNIT
(EEP ROM)Ð
Initial startIThis is not a malfunction mes-
sage (Whenever shutting off a
power supply to the TCM, this
message appears on the
screen.)XÐ
INITIAL START
Ð
No failure
(NO DTC IS DETECTED FURTHER TEST-
ING MAY BE REQUIRED)INo failure has been detected.
XX
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont'd)
AT-39

X: Applicable
Ð: Not applicable
*1: These malfunctions cannot be displayed by MIL
if another malfunction is assigned to MIL.
*2: Refer to EC-74, ªDESCRIPTIONº.
DATA MONITOR MODE (A/T)NBAT0184S03
Item DisplayMonitor item
Description Remarks
TCM input
signalsMain sig-
nals
Vehicle speed sensor 1
(A/T)
(Revolution sensor)VHCL/S SE´A/T
[km/h] or [mph]
XÐIVehicle speed computed
from signal of revolution
sensor is displayed.When racing engine in ªNº
or ªPº position with vehicle
stationary, CONSULT-II
data may not indicate 0
km/h (0 mph).
Vehicle speed sensor 2
(Meter)VHCL/S SE´MTR
[km/h] or [mph]
XÐIVehicle speed computed
from signal of vehicle
speed sensor is dis-
played.Vehicle speed display may
not be accurate under
approx. 10 km/h (6 mph). It
may not indicate 0 km/h (0
mph) when vehicle is sta-
tionary.
Throttle position sensor THRTL POS
SEN
[V]XÐIThrottle position sensor
signal voltage is dis-
played.
A/T fluid temperature sen-
sorFLUID TEMP SE
[V]
XÐIA/T fluid temperature
sensor signal voltage is
displayed.
ISignal voltage lowers as
fluid temperature rises.
Battery voltage BATTERY VOLT
[V]XÐISource voltage of TCM
is displayed.
Engine speed ENGINE SPEED
[rpm]
XXIEngine speed, computed
from engine speed
signal, is displayed.Engine speed display may
not be accurate under
approx. 800 rpm. It may
not indicate 0 rpm even
when engine is not run-
ning.
Turbine revolution sensor TURBINE REV
[rpm]
XÐITurbine revolution com-
puted from signal of tur-
bine revolution sensor is
displayed.Error may occur under
approx. 800 rpm and will
not indicate 0 rpm even if
engine is not running.
Overdrive control switch OVERDRIVE SW
[ON/OFF] X ÐION/OFF state computed
from signal of overdrive
control SW is displayed.
PN position switch PN POSI SW
[ON/OFF] X ÐION/OFF state computed
from signal of PN posi-
tion SW is displayed.
R position switch R POSITION SW
[ON/OFF] X ÐION/OFF state computed
from signal of R position
SW is displayed.
D position switch D POSITION SW
[ON/OFF] X ÐION/OFF state computed
from signal of D position
SW is displayed.
2 position switch 2 POSITION SW
[ON/OFF]
XÐION/OFF status, com-
puted from signal of 2
position SW, is dis-
played.
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
CONSULT-II (Cont'd)
AT-40

1 CHECK O/D OFF INDICATOR LAMP
1. Start the engine with selector lever in ªPº position. Warm engine to normal operating temperature.
2. Turn ignition switch to ªOFFº position.
3. Wait 5 seconds.
SAT967I
4. Turn ignition switch to ªONº position.
(Do not start engine.)
5. Does O/D OFF indicator lamp come on for about 2 seconds?
SAT133K
YesorNo
Ye s©GO TO 2.
No©Go to ª1. O/D OFF Indicator Lamp Does Not Come Onº, AT-218.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Diagnostic Procedure Without CONSULT-II (Cont'd)
AT-47

2 JUDGEMENT PROCEDURE STEP 1
1. Turn ignition switch to ªOFFº position.
2. Push shift lock release button.
3. Move selector lever from ªPº to ªDº position.
4. Turn ignition switch to ªONº position. (Do not start engine.)
5. Depress and hold overdrive control switch in ªOFFº position (the O/D OFF indicator lamp will be ªONº) until directed to
release the switch. (If O/D OFF indicator lamp does not come on, go to step 5 on AT-257.)
6. Turn ignition switch to ªOFFº position.
SAT968I
7. Turn ignition switch to ªONº position (Do not start engine.).
8. Release the overdrive control switch (the O/D OFF indicator lamp will be ªOFFº).
9. Wait 2 seconds.
10. Move selector lever to ª2º position.
11. Depress and release the overdrive control switch (the O/D OFF indicator lamp will be ªONº).
12. Depress and hold the overdrive control switch (the O/D OFF indicator lamp will be ªOFFº) until directed to release the
switch.
SAT969I
©GO TO 3.
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Diagnostic Procedure Without CONSULT-II (Cont'd)
AT-48

O/D OFF indicator lamp:
6th judgement flicker is longer than others.
SAT672I
Overrun clutch solenoid valve circuit is short-circuited or discon-
nected.
ÞGo to DTC P1760 OVERRUN CLUTCH SOLENOID VALVE,
AT-185.7th judgement flicker is longer than others.
SAT673I
Torque converter clutch solenoid valve circuit is short-circuited
or disconnected.
ÞGo to DTC P0740 TORQUE CONVERTER CLUTCH SOLE-
NOID VALVE, AT-148.
8th judgement flicker is longer than others.
SAT674I
A/T fluid temperature sensor is disconnected or TCM power
source circuit is damaged.
ÞGo to DTC BATT/FLUID TEMP SEN (A/T FLUID TEM-
PERATURE SENSOR AND TCM POWER SOURCE), AT-190.9th judgement flicker is longer than others.
SAT675I
Engine speed signal circuit is short-circuited or disconnected.
ÞGo to DTC P0725 ENGINE SPEED SIGNAL, AT-116.
10th judgement flicker is longer than others.
SAT676I
Turbine revolution sensor circuit is short-circuited or discon-
nected.
ÞGo to DTC Turbine Revolution Sensor, AT-202.11th judgement flicker is longer than others.
SAT677I
Line pressure solenoid valve circuit is short-circuited or discon-
nected.
ÞGo to DTC P0745 LINE PRESSURE SOLENOID VALVE,
AT-162.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Diagnostic Procedure Without CONSULT-II (Cont'd)
AT-51