2001 HONDA ACCORD SEDAN radio

Audio System
Adjusting the Sound
Bass, Treble, Balance, and Fader are
each adjustable. You select which of
these you want to adjust by pressing
the TUNE knob. The mode changes from BAS to TRE to FAD to BAL,and then back to the selected audio
mode, each time you press the
TUNE knob.
Balance/Fader — These two
modes adjust the strength of the
sound coming from each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the front-to-back
strength.

Select BAL or FAD by pressing the
TUNE knob. Adjust the Balance or Fader to your liking by turning the
TUNE knob. The level number on the display shows you the range. LEVEL NUMBER INDICATOR
Treble/Bass — Use these modes to adjust the tone to your liking. Select
TRE or BAS by pressing the TUNE knob. Adjust the desired mode by
turning the TUNE knob. The level number on the display shows you the

range.
The system will automatically return
the display to the selected audiomode about five seconds after youstop adjusting a mode with the
TUNE knob.

Radio Frequencies and Reception
For information, See page 158 .

Comfort and Convenience Features TUNE/MODE KNOB

Audio System

Audio System Lighting You can use the instrument panelbrightness control dial to adjust the il-lumination of the audio system (see
page 62 ). The audio system
illuminates when the parking lightsare on, even if the radio is turned off.
Operating the CD Player
You operate the CD player with the same controls used for the radio.
With the ignition switch in
ACCESSORY (I) or ON (II), insert
the disc into the CD slot. Push the
disc in halfway, the drive will pull it
in the rest of the way and begin to
play. The number of the track that is
playing is shown in the display. You can also play 3-inch (8-cm) discs
without using an adapter ring. Play
only standard round discs. Odd-
shaped CDs may jam in the drive or
cause other problems.
When the system reaches the end of the disc, it will return to the begin-ning and play that disc again.
Comfort and Convenience Features
AM/FM BUTTON

CD/TAPE BUTTON

REPEAT INDICATOR

CD SLOT REPEAT BUTTON

EJECT

BUTTON
RANDOM BUTTON
RANDOM INDICATOR

SEEK/SKIP BAR

PWR/VOL KNOB

Audio System

You can switch to the radio while a CD is playing by pressing the AM/
FM button. Press the CD button to
return to playing the CD. The CD
will begin playing where it left off.
If you turn the system off while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the disc will stay in the drive. When
you turn the system back on, the CD will begin playing where it left off. Press the eject button to remove the
disc from the drive.
If you eject the disc, but do not
remove it from the slot, the system
will automatically reload the disc after 15 seconds and put the CD
player in pause mode. To begin
playing the disc, press the CD button. You can use the SEEK/SKIP bar
while a disc is playing to select
passages and change tracks.
To move rapidly within a track, press and hold the SEEK/SKIP bar. Press the side to move forward. You
will see CUE in the display. Press the side to move backward. You
will see REW displayed. Release the
bar when the system reaches the point you want.
Each time you press and release the side of the SEEK/SKIP bar,
the system skips forward to the
beginning of the next track. Press the side to skip backward to the
beginning of the current track. Press
it again to skip to the beginning of
the previous track.
Comfort and Convenience Features

Audio System
The tape direction indicator will light to show you which side of the cassette is playing. The indicates
the side you inserted facing upward
is now playing. If you want to play
the other side, press the PROG
button. Dolby B noise reduction turns on
when you insert a cassette. If the tape was not recorded with Dolby B
noise reduction, turn it off by
pressing the NR button.
Dolby remains off until you turn it on
by pressing the button again.
When the system reaches the end of the tape, it will automatically reversedirection and play the other side. If
you want to remove the cassette
from the drive, press the EJECT button on the cassette player.
If you turn the system off while a

tape is playing, either with the PWR/

VOL knob or by turning off the
ignition, the cassette will remain in

the drive. When you turn the system

back on, the cassette player will be in

pause mode. To begin playing, press

the PLAY button.

To switch to the radio or CD player
while a tape is playing, press the

AM/FM, or CD button. To change
back to the cassette player, push the
CD button.
Comfort and Convenience Features

Audio System

AM/FM/Cassette/CD Changer
Audio System For EX and EX-V6

Your Honda's audio system provides clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your favorite stations.
The cassette system features Dolby B* noise reduction, automaticsensing of chromium-dioxide (CrO2)
tape, and autoreverse for continuous
play.
* Dolby noise reduction manufactured under
license from Dolby Laboratories Licensing Corpo-
ration. "DOLBY" and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation.

The in-dash CD changer holds up to six discs. You operate the CD
changer with the same controls used
for the radio. See page 165 for CD
changer operation. The anti-theft feature will disable the
system if it is disconnected from the
car's battery. To get the system
working again, you must enter a
code number (see page 174 ).

Comfort and Convenience Features

Audio System

Operating the Radio
The ignition switch must be in
ACCESSORY (I) or ON (II) to operate the audio system. Turn the
system on by pressing the PWR/
VOL knob or the AM or FM button.
Adjust the volume by turning the knob.
The band and frequency that the radio was last tuned to is displayed.
To change bands, press the AM or FM button. On the FM band, ST will
be displayed if the station is broad- casting in stereo. Stereo
reproduction on AM is not available. You can use any of four methods to
find radio stations on the selected
band: TUNE, SEEK, SCAN or thePreset buttons.
TUNE — Use the TUNE knob to tune the radio to a desired frequency.
Turn the TUNE knob to the right to tune to a higher frequency, or to theleft to tune to a lower frequency.
Turn the knob right or left until the display reaches the desired
frequency.
SEEK — The SEEK functionsearches the band for a station with
a strong signal. To activate it, press either SEEK button ( or ), then
release it. Depending on which
SEEK button you press, the system
scans upward or downward from the
current frequency. It stops when it
finds a station with a strong signal. SCAN — The SCAN function
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. When the system is in the SCAN mode, SCAN shows in
the display. The system will scan up
the band for a station with a strongsignal. When it finds one, it will stop
and play that station for
approximately five seconds. If you do
nothing, the system will then scan
for the next strong station and play
that for five seconds. When it plays a station that you want to continue
listening to, press the SCAN button
again.

Comfort and Convenience Features

Audio System

Preset — You can store the
frequencies of your favorite radio stations in the six preset buttons.
Each button will store one frequency
on the AM band, and two
frequencies on the FM band.
To store a frequency:
1. Select the desired band, AM or FM. FM1 and FM2 let you store
two frequencies with each Preset

button.

2. Use the TUNE or SEEK function to tune the radio to a desired
station.

3. Pick the Preset button you want for that station. Press the button
and hold it until you hear a beep.
4. Repeat steps 1 to 3 to store a total of six stations on AM and twelve
on FM. PWR/VOL
KNOB
FM
BUTTON TUNE KNOB
SEEKBUTTONS
SCAN BUTTON
PRESET BUTTONS

Once a station's frequency is stored,

simply press and release the proper

Preset button to tune to it. The preset frequencies will be lost if
your car's battery goes dead, is disconnected, or the radio fuse is

removed.

Comfort and Convenience Features
CONTINUED

AM

BUTTON
STEREO
INDICATOR

Audio System

Audio System LightingYou can use the instrument panel brightness control dial to adjust the il-
lumination of the audio system (see
page 63 ). The audio system
illuminates when the parking lightsare on, even if the radio is turned off.
Radio Frequencies
Your Honda's radio can receive the complete AM and FM bands.
Those bands cover these frequen-
cies:

AM band:
530 to 1,710 kilohertz

FM band:

87.7 to 107.9 megahertz
Radio stations on the AM band are
assigned frequencies at least ten
kilohertz apart (530, 540, 550). Stations on the FM band are
assigned frequencies at least 0.2
megahertz apart (87.9, 88.1, 88.3). Stations must use these exact
frequencies. It is fairly common for stations to round-off the frequency in
their advertising, so your radio could display a frequency of 100.9 even
though the announcer may identify
the station as "FM101."
Radio Reception How well your Honda's radio
receives stations is dependent on
many factors, such as the distance
from the station's transmitter, nearby large objects, and atmos-
pheric conditions.
A radio station's signal gets weaker as you get farther away from its
transmitter. If you are listening to an
AM station, you will notice the sound volume becoming weaker, and the station drifting in and out. If you are
listening to an FM station, you will see the stereo indicator flickering off
and on as the signal weakens.
Eventually, the stereo indicator will go off and the sound will fade
completely as you get out of range of
the station's signal.
Driving very near the transmitter of
a station that is broadcasting on a
frequency close to the frequency of
the station you are listening to can also affect your radio's reception.
You may temporarily hear both stations, or hear only the station you
are close to.
Comfort and Convenience Features