2001 HONDA ACCORD cooling

µ
Ì
Î ÎÎ ÌÌ
ÌÎÎ
Î
Î Follow the Maintenance
Schedule f or Severe Conditions.
Follow the Severe Conditions
Maintenance Schedule if you
drive your vehicle
under one or more of the
f ollowing conditions:
Driving less than 5 miles (8
km) per trip or, in f reezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving.
Trailer towing, driving with a
car top carrier, or driving in
mountainous conditions.
Driving on muddy, dusty, or
de-iced roads.
MAINLY
Maint enance U.S. Owners
Canadian Owners
226 Visually inspect the following items:Replace every 3,750 miles (6,000 km) or 6 months
Check oil and coolant at each fuel stop
Service at the indicated
distance or time whichever
comes first.
miles x 1,000
km x 1,000
months
See air conditioning filter on page for replacement information under special driving conditions.
Balancer belt applies to 4-cylinder models only.
See timing belt on page to determine need for replacement.
See information on maintenance and emissions warranty, last column, page .
Tie rod ends, steering gear box, and boots
Suspension components, driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and conditions of fluids
Cooling system hoses and connections
Exhaust system, fuel lines and connections
Lights and controls, vehicle underbody Every 7,500 miles (12,000 km) or 6 months
Replace engine oil and oil filter
Check engine oil and coolant
Clean ( ) or replace ( ) air cleaner element
Use normal schedule except in dusty conditons
Inspect valve clearance
Replace spark plugs
Replace timing belt , balancer belt , and
inspect water pump
Inspect and adjust drive belts
Inspect idle speed
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace air conditioning filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition
at least once per month) Rotate tires every 7,500 miles (12,000 km)
152412
304824 457236609648 75
120 60 105168
84 120192
96
90
144
72
At 60,000 miles (96,000 km) or 36 months, thereafter every 30,000 mi, (48,000 km) or 24 months
At 60,000 miles (96,000 km) or 36 months
Every 36 months
Adjust only if noisy
:
1:2:3: 223
267
266 Every 7,500 miles (12,000 km) or 6 months
MTAT
11
,2
3
120,000 miles (200,000 km) or 10 years, thereafter every 60,000 miles (100,000 km) or 60 months
Maintenance Schedule for Severe Conditions

Ø Ø Ø ØØØØØØØØ
Ø Ø
Ø
ØØ Ø Ø Ø Ø Ø Ì Ì
Î
ÎÎ
Î
ÎÎ Î
Ì Î ÎÎ
Maint enance
228 D E
82,500 mi/132,000 km
86,250 mi/138,000 km
90,000 mi/144,000 km/6 yrs
93,750 mi/150,000 km
97,500 mi/156,000 km
101,250 mi/162,000 km
105,000 mi/168,000 km/7 yrs
108,750 mi/174,000 km
112,500 mi/180,000 km
116,250 mi/186,000 km
120,000 mi/192,000 km/8 yrs
At 120,000 mi/200,000 km/72
months, thereafter every
60,000 mi/100,000 km/60 mos
Every 60,000 mi/96,000 km/36mos
At 60,000 miles/96,000 km or
36 months, thereafter every
30,000 mi/48,000 km/24 mos Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections.
Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Replace air cleaner element.
Inspect and adjust drive belts.
Replace air conditioning filter .
Replace brake fluid every 3 years.
(independent of mileage)
Do items in A, B.
Do items in A.
Replacebrakefluid.DoitemsinA,B,C,D,E.
Do items in A.
Do items in A, B.
Do items in A. Replace timing belt , balancer belt , and
inspect water pump. Inspect valve clearance. Check idle speed. Clean air cleaner element.
Replace spark plugs. Do items in A, B, C.
Do items in A.
Do items in A, B.
Do items in A.
Replace timing belt , balancer belt , and
inspect water pump. Do items in A, B, C, D.
Replace engine coolant
Replace manual transmission fluid
Replace automatic transmission fluid See air conditioning filter on page for replacement information
under special driving conditions.
Balancer belt applies to 4-cylinder models only.
See timing belt on page to determine need for replacement.
See information on maintenance and emissions warranty, last
column, page .
:
1:2:3: 223
267
2663
11
,2
11 ,2
Maintenance Schedule for Severe Conditions (listed by distance/time)

If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks.
This coolant should always be a
mixtureof 50percentantifreezeand
50 percent water. Never add straight
antif reeze or plain water.Always use Genuine Honda All
Season Antif reeze/Coolant Type 2.
This coolant is pre-mixed with 50
percent antif reeze and 50 percent
water. It does not require any
additional mixing. If it is not available,
you may use another major-brand
non-silicate coolant as a temporary
replacement. Make sure it is a high-
quality coolant recommended f or
aluminum engines. However,
continued use of any non-Hondacoolant can result in corrosion,
causingthecoolingsystemto
malf unction or f ail. Have the cooling
system f lushed and ref illed with
Honda antif reeze/coolant as soon as
possible.
If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
CONT INUED
A dding Engine Coolant
Maint enance
Cooling Syst em
239
66--ccyylliinnddeerrmmooddeellss44--ccyylliinnddeerrmmooddeellssRREESSEERRVVEETTAANNKKRREESSEERRVVEETTAANNKK

Remove the radiator cap by
pushing down and turning
counterclockwise.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Make sure the engine and radiator
are cool.
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Put the radiator cap back on.
Tighten it f ully.
3.
1. 2.
4. 5.
Cooling Syst em
Maint enance
240
44--ccyylliinnddeerrmmooddeellss66--ccyylliinnddeerrmmooddeellssRRAADDIIAATTOORRCCAAPP
RRAADDIIAATTOORRCCAAPP
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.

Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Genuine Honda All season
Antif reeze/Coolant Type 2.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank. Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents. Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
6.
CONT INUED
Replacing Engine Coolant
Cooling Syst em
Maint enance 241
44--ccyylliinnddeerrmmooddeellssRREESSEERRVVEETTAANNKK66--ccyylliinnddeerrmmooddeellssRREESSEERRVVEETTAANNKK

Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.
Openthehood.Makesurethe
engine and radiator are cool to the
touch.
Turn the ignition ON (II). Turn
the temperature control dial to
90°F (32°C). Turn of f the ignition
and remove the key.
Remove the radiator cap.
Turn the ignition ON (II). Turn
the temperature control Dial all
the way clockwise. Turn of f the
ignition and remove the key.
1.
3.
2.
4-cylinder models
EX-V6 model
Except EX-V6 model
Maint enance
Cooling Syst em
242
44--ccyylliinnddeerrmmooddeellss66--ccyylliinnddeerrmmooddeellss44--ccyylliinnddeerrmmooddeellss
DDRRAAIINNBBOOLLTT
DDRRAAIINNPPLLUUGG

Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Loosen the drain
bolt. When removing the reserve tank,
f irst remove the cruise control cable
and the ground cable f rom their clips.
After installing the tank back in
place, put the cables back in their
clips.
4.
3.6-cylinder models 6-cylinder models
CONT INUED
Cooling Syst em
Maint enance243
66--ccyylliinnddeerrmmooddeellss
RREESSEERRVVEETTAANNKKRREESSEERRVVEETTAANNKKCCAAPP
44--ccyylliinnddeerrmmooddeellssHHOOLLDDEERR
DDRRAAIINNPPLLUUGG
DDRRAAIINNBBOOLLTT66--ccyylliinnddeerrmmooddeellss

When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque:
Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator. This coolant is a
mixture of 50 percent anti-f reeze
and 50 percent water. Pre-mixing
is not required.
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles.
7.
6.
5.
4-cylinder models 6-cylinder models 4-cylinder models
Cooling Syst em
Maint enance
244
FFIILLLLEERRNNEECCKK
44--ccyylliinnddeerrmmooddeellssFFiilllluuppttoohheerree
FFIILLLLEERRNNEECCKK
66--ccyylliinnddeerrmmooddeellssFFiilllluuppttoohheerree
RREESSEERRVVEETTAANNKKCCAAPPRREESSEERRVVEETTAANNKK
66--ccyylliinnddeerrmmooddeellssHHOOLLDDEERR
61 lbf·ft (83 N·m , 8.5 kgf·m) 7 lbf·ft (10 N·m , 1.0 kgf·m)