2001 HONDA ACCORD COUPE ECU

Protecting Children
If it is necessary to put a forward-
facing child seat in the front, move
the vehicle seat as far to the rear as
possible, be sure the child seat is
firmly secured to the car, and the child is properly strapped in the seat.
Child Seat Installation

The lap/shoulder belts in the back and front passenger seating positions
have a locking mechanism that must
be activated to secure a child seat.
The following pages provide instructions on how to secure aforward-facing child seat with this
type of seat belt.
If you have a child seat designed to
attach to the vehicle's lower
anchorages, follow the instructions
on page 39 . 1. With the child seat in the desired
seating position, route the belt
through the child seat according
to the seat maker's instructions,
then insert the latch plate into the buckle.

Driver and Passenger Safety

Improperly placing a forward-
facing child seat in the front seat can result in serious injuryor death if the front airbags
inflate.

If you must place a forward-
facing child seat in front, move
the vehicle seat as far back as possible and properly restrain
the child.

Protecting Children

2. To activate the lockable retractor,
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt feed back into the
retractor (you might hear a
clicking noise as the belt retracts).
3. After the belt has retracted, tug on
it. If the belt is locked, you will not
be able to pull it out. If you can pull
the belt out, it is not locked and
you will need to repeat these steps.
4. After confirming that the belt is
locked, grab the shoulder part of
the belt near the buckle and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure. It
may help to put weight on the
child seat, or push on the back of
the seat, while pulling up on the
belt.

5. Push and pull the child seat
forward and from side to side to

verify that it is secure enough to
stay upright during normal driving

maneuvers. If the child seat is not

secure, unlatch the belt, allow it to

retract fully, then repeat these

steps.

To deactivate the locking
mechanism in order to remove a

child seat, unlatch the buckle,

unroute the seat belt, and let the belt

fully retract.

Driver and Passenger Safety

Protecting Children

If you decide that a child can safely
ride up front, be sure to: Carefully read the owner's manual
and make sure you understand all
seat belt instructions and all safety
information.
Move the vehicle seat to the rear-
most position.
Have the child sit up straight, back
against the seat, and feet on or
near the floor.
Check that the child's seat belt is
properly positioned and secured. Supervise the child. Even mature
children sometimes need to be
reminded to fasten the seat belts
or sit properly. Using Child Seats with Tethers
Your car has three tether anchorage
points under the rear window for securing a tether-style child seat to
the car.
Since a tether can provide additional
security, we recommend using a
tether whenever one is required or
available.

CONTINUED
Driver and Passenger Safety

Protecting Children

Attach the tether strap hook to thetether anchorage point and tighten
the strap according to the child seat
maker's instructions. Using the Lower Anchorages
Your car is equipped with lower anchorages at the outer rear seats.
These anchorages are located between the seat-back and seat
bottom and are only to be used with a child seat designed to attach to the
lower anchorages.
The exact location of each anchor is marked with a small circle above the
lower anchor point. To install a child seat designed to
attached to the lower anchorages:
1. Move the seat belt buckle or center seat belt away from the
anchorages.

2. Make sure there are no foreign objects around the anchorages.
Foreign objects could get in the
way of a secure connection
between the child seat and the
anchorage.

Driver and Passenger Safety
LOWER ANCHORAGES

Rigid type

Protecting Children

3. Put the child seat in the rear left or right vehicle seat and attach thechild seat to the lower anchorages
according to the child seat maker's

instructions.

4. Follow the child seat maker's instructions for any additionaladvice on adjusting or tightening
the fit.
5. Attach the tether strap hook to the
tether anchorage point and tightenthe strap according to the child seat maker's instructions.
6. Push and pull the child seat forward and from side to side to
verify that it is secure enough to stay upright during normal driving
maneuvers.
Driver and Passenger Safety
Flexible type

Additional Information About Your Seat Belts

Seat Belt System Components

Your seat belt system includes lap/ shoulder belts in all five seating
positions.
The seat belt system alsoincludes a light on the
instrument panel to remind you and
your passengers to fasten your belts. If the driver's seat belt is not
fastened before the ignition is turned ON (II), the light will come on and a
beeper will also sound. The beeper
will stop after a few seconds, but the light will stay on until the driver'sseat belt is fastened. Lap/Shoulder Belt
This seat belt has a single belt that goes over your shoulder, across yourchest and across your hips.
To fasten the belt, insert the latch plate into the buckle, then tug on the
belt to make sure the buckle is

latched.
To unlock the belt, push the red
PRESS button on the buckle.
Guide the belt across your body to
the door pillar. After exiting the car, be sure the belt is out of the way and
will not get closed in the door.
All seat belts have an emergency locking retractor. In normal driving,
the retractor lets you move freely in
your seat while it keeps some tension on the belt. During a collisionor sudden stop, the retractor
automatically locks the belt to help
restrain your body.
The seat belts in all seating positions except the driver's have an additional
locking mechanism that must be activated to secure a child seat. (See
pages 29 and 33 for instructions on
how to secure child seats with this
type of seat belt.)
Driver and Passenger Safety
SHOULDER
PORTION

UPPER SEAT
BELT ANCHOR

LATCH
PLATE
BUCKLE LAP PORTION

Controls Near the Steering Wheel
Make sure the rear window is clear
and you have good visibility before
starting to drive.
The defogger and antenna wires on the inside of the rear window can beaccidentally damaged. When
cleaning the glass, always wipe side
to side. Steering Wheel Adjustment

See page 16 for important safety
information about how to properly

position the steering wheel.
Make any steering wheel adjustment
before you start driving.
To adjust the steering wheel upward or downward:
1. Push the lever under the steering column all the way down. 2. Move the steering wheel to the
desired position, making sure the
wheel points toward your chest, not toward your face. Make sure
you can see the instrument panel gauges and the indicator lights.
3. Push the lever up to lock the steering wheel in that position.
4. Make sure you have securely locked the steering wheel in placeby trying to move it up and down.

Instruments and Controls

Adjusting the steering wheel
position while driving may
cause you to lose control of the car and be seriously injured in a
crash.
Adjust the steering wheel only
when the car is stopped.

Keys and Locks

You cannot lock or unlock the doors with the remote transmitter if anydoor is not fully closed or the key is
in the ignition switch.
If you unlock the doors with the
remote transmitter, but do not open any of the doors within 20 seconds,
the doors automatically relock and
the security system sets.
When you push the LOCK button a second time within 5 seconds after
you have locked the doors, the horn
will sound once to verify that the security system will be set. To open the trunk, push the Trunk
Release button for approximately
one second.
The trunk will not open if the key is in the ignition switch.
Panic Mode

Panic mode allows you to remotely
activate your car's security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will flash, for about 30 seconds.
To activate panic mode, press and hold the PANIC button for about two
seconds.

To cancel Panic mode before 30 seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).

CONTINUED

Instruments and Controls