Page 16 of 443

1-9
Folding the Seatbacks
CAUTION:
If the seatback isn't locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
press rearward on the seatback to be sure it
is locked.
On all models with 60/40 split bench seats, you must
insert the center occupant lap belt latch plate into the
loop provided, on the underside of the folded forward
seat cushion, before folding the rear seat back down on
the driver's side.
You may have to adjust the location of the latch plate on
the webbing so that it reaches the loop. Stowing in this
loop will reduce the chances of damaging and soiling
the belt. Remember to remove the latch plate from the
loop before the seat is returned to the passenger position.
On Suburban/Yukon XL insert the two buckles into
the retainer in the seatback, before folding the rear
seat on the driver's side. The buckles will be out of
the way when the seat is folded and will be available
for passengers to use when the seat is returned to the
passenger position. Also, make sure that nothing is
under or in front of the seat and that the head restraints
are completely lowered.
On Tahoe/Yukon models the rear seatbacks may be
equipped with rearward folding head restraints. When
the seatback is being folded down, the head restraint will
automatically fold rearward to allow a flat load floor for
cargo or entry to the third row seat (if equipped).
Page 19 of 443

1-12
CAUTION:
If a head restraint is not installed on the seatback
or stored in the vehicle properly, it could be thrown
about the vehicle in a crash or sudden maneuver.
People in the vehicle could be injured. Remove the
head restraints only when you need to fold the seat,
and be sure that the head restraints are stored
securely in the space provided in the folded up
seat cushion. When the seat is returned to the
passenger position, be sure the head restraints are
installed properly.
On Suburban/Yukon XL models with rear bucket seats,
the head restraints need to be removed in order to fold
the rear seats. To do this follow these directions:
1. Lift the head restraints up until they stop.
2. Press in the button on the side of the head restraint
guide cap and lift up on the head restraint.
3. Do the same for the other cap.
The head restraint can be removed and stored in the
space provided in the folded up seat cushion.To fold the seatbacks on the bucket seats, do the following:
1. Pull up on the strap loop
located at the rear of the
seat cushion and pull the
seat cushion up. Then
fold it forward.
2. Push the
seatback release
lever rearward
and pull the
seatback forward.
Then fold it until
it is flat.
If the seatback cannot fold flat because it interferes with
the cushion, try moving the front seat forward and/or
bringing the front seatback more upright.
Page 20 of 443

1-13
Once the seatbacks are folded down, the rear seat
footwell area will be exposed and will have to be
covered by the load floor panel. To create a load
floor, do the following:
1. Release the panels from the seatbacks by pushing
forward on the latches.
2. Then fold the panels back to cover the rear seat
footwell area.
If you have removed the head restraints to fold the rear
bucket seat, be sure to reinstall them on the seatback
after it has been returned to the normal seating position.
50/50 Split Bench Seat (Third Row)
If your vehicle has a 50/50 split bench, the seatback(s)
can be folded and the entire seat(s) tilted or removed
from the vehicles.
Folding the Seatbacks
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
To fold the seatbacks do the following:
Pull up on the release lever, labeled 1, located on the
rear of the seatback, and push the seatback forward.
To return the seat to the passenger position, pull
up on the release lever labeled 1 and then pull up
on the seatback until the seatback locks into the
upright position.
Push forward on the seatback to make sure it is locked
into position.
Page 22 of 443

1-15
To return the seat to the seating position do the
following:
1. Push forward on the seat and release the support
lock rod.
2. Secure the support rod in its stored position on the
underside of the seat.
3. Lower the seat to the floor and let the seat drop
into place.
4. Lift up on the carrying handle to make sure the seat
is locked in place.
5. Return the seatback to the upright position by pulling
up on the release lever labeled 1 before the back can
be folded upright.
6. Pull the seatback forward to make sure it is locked
in place.
Removing the 50/50 Split Bench Seat
To remove the 50/50 split bench seat, do the following:
1. Open the rear doors and enter the rear of the vehicle.2. Fold the seatback
forward onto the seat
cushion by using the
lever labeled 1. The seat
cannot be removed
unless the seatback
is folded.
3. To unlatch the seat from
the floor, pull up on the
release lever labeled 2,
located at the rear of the
seat, and lift the rear of
the seat up off the floor.
Page 24 of 443
1-17 Full Bench Seat (Third Row)
If your vehicle has a full bench seat, the seatback can
be folded and the seat can be tilted or removed from
the vehicle.
Folding the Seatback
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
To fold the seatback on the bench seat, do the following:
1. Pull up on the release
lever, labeled 1, located
on the rear of the
seatback and push the
seatback forward.
2. To return the seat to an upright position, pull up
on the release lever labeled 1 and then pull up on
the seatback until the seatback locks into the
upright position.
Push and pull on the seatback to check that it is locked
into place.
Page 26 of 443

1-19
5. Tilt the seat fully forward and secure it in place using
the support rod located on the underside of the seat
on the passenger's side. Make sure the rod pin is
fully engaged in the lock.
6. Push and pull on the seat. Make sure the support
rod is holding it firmly in place. Use the seat in
this position only when necessary for additional
cargo space.
To return the seat to the seating position do
the following:
1. Push forward on the seat and release the support
lock rod.
2. Secure the support rod in its stored position on the
underside of the seat.
3. Lower the seat to the floor and let the seat drop
into place.
4. Lift up on the carrying handle to make sure the seat
is locked in place.
5. Return the seatback to the upright position by pulling
up on the release lever labeled 1 before the back can
be folded upright.
6. Pull the seatback forward to make sure it is locked
in place.Removing the Full Bench Seat
To remove the full bench seat, do the following:
1. Open the rear doors and enter the rear of the vehicle.
2. Fold the seatback
forward onto the seat
cushion by using the
lever labeled 1. The seat
cannot be removed
unless the seatback
is folded.
Page 61 of 443

1-54
Third Row Seat
4. Buckle, position and release the safety belt as
described in ªRear Seat Outside Passenger Positionsº
earlier in this section. Make sure that the shoulder
belt crosses the shoulder.
To remove and store the comfort guides, squeeze the
belt edges together so that you can take them out of the
guides. Make sure you remove the comfort guide from
the belt before you fold a rear seat down or use an
easy
-entry seat, if your vehicle has one.
Children
Everyone in a vehicle needs protection! This includes
infants and all other children. Neither the distance
traveled nor the age and size of the traveler changes the
need, for everyone, to use safety restraints. In fact, the
law in every state in the United States and in every
Canadian province says children up to some age must be
restrained while in a vehicle.
Infants and Young Children
Every time infants and young children ride in vehicles,
they should have the protection provided by the
appropriate restraint. Young children should not use the
vehicle's safety belts, unless there is no other choice.
Page 75 of 443
1-68
Securing a Child Restraint Designed for the
LATCH System
1. Find the anchors for the seating position you want to
use, where the bottom of the seatback meets the back
of the seat cushion.
2. Put the child restraint on the seat.
3. Attach the anchor points on the child restraint to the
anchors in the vehicle. The child restraint
instructions will show you how.
4. If the child restraint is forward
-facing, attach the top
strap to the top strap anchor. See ªTop Strapº in the
Index. Tighten the top strap according to the child
restraint instructions.
5. Push and pull the child restraint in different
directions to be sure it is secure.
To remove the child restraint, simply unhook the top
strap from the top tether anchor and then disconnect the
anchor points.
Securing a Child Restraint in a Rear
Outside Seat Position
If your child restraint is equipped with the LATCH
system, see ªLower Anchorages and Top Tethers for
Children (LATCH)º in the Index.