2001 CADILLAC CATERA climate settings

1-6 Heated Front Seats (Option)
The controls for the heated
front seats are located next
to the climate controls on
either side of the center
console. Turning the
driver or passenger side
thumbwheel control
counterclockwise from
the off position activates
the heated seat.
The control can be adjusted to one of five heat settings,
numbered ª1 through 5º, with 1 being the lowest setting
and 5 being the highest setting.
An indicator light in the control reminds you that the
heating system is in use. The heated seats can only be
used when the ignition is turned on.
To turn the heated seat off, turn the thumbwheel control
clockwise to the off position.
Reclining Front Seatbacks
The manual recliner
control is located
on the side of the
seatback closet to
the door, below the
lumbar control.
To move the seatback forward, turn the hand
-wheel control
forward. Turn the control rearward to recline the seatback.
If you have a power
recliner, the power control
is located on the outboard
side of each front seatback.
Press the control forward
or rearward to adjust
the seatback.

3-3
Outside Temperature Display
The outside temperature is always displayed when your
vehicle's ignition is on. If the outside temperature
display begins to flash, this means that icy road
conditions are possible. Adjust your driving if needed.
The display will flash for about 30 seconds and then
remain on steady.
Mode Button
Press this button to deliver air through the floor, middle
or windshield outlets. The climate control system will
stay in the selected ECC mode until the MODE button is
pressed again or until the TEMP/AUTO knob is pressed.
Press the up or down arrow to see the available modes.
English/Metric Display
You can change the temperature display from English
(degrees Fahrenheit) to metric (degrees Celsius) by
pressing and holding the driver's side TEMP/AUTO
knob for approximately five seconds. Repeat the process
to change back to English from metric.Automatic Operation
Pressing the driver's side TEMP/AUTO knob sets the
system for automatic operation. Once the system is set,
sensors will control the air delivery mode. Air will come
from the floor, middle, side or windshield outlets. The
fan speed will vary as the system maintains the selected
temperature setting. (All previous manually set mode
settings will change back to a fully automatic mode
when the climate control system is turned on this way.)
Be careful not to put anything over the solar sensor
located in the middle of the instrument panel near the
windshield. This sensor is used by the automatic system
to regulate temperature.
To find your comfort zone, start with the 75
F (24
C)
setting and allow about 20 minutes for the system to
regulate air temperature. Adjust the temperature if
necessary. If you choose 60
F (16
C), the system will
remain at that maximum cooling setting and will not
regulate fan speed. If you choose the temperature of
90
F (32
C), the system will remain at that maximum
heating setting and will not regulate fan speed. Choosing
either maximum setting will not cause the system to heat
or cool any faster.

3-5
DEFROST: This setting sends most of the airflow
to the windshield with only a small amount to the
floor outlets. Press this button to quickly remove fog or
frost from the windshield (the fan works in high
-speed).
FAN SPEEDS: Press the driver's side
TEMP/AUTO knob to set the fan speed for AUTO.
In this setting, the fan speed is automatically controlled.
If it is cold outside, the fan may not run in the maximum
high fan speed right away. The system checks the
temperature of the engine coolant to assure it is warm
enough to provide heat. When the engine coolant is
warm, the controller allows the fan to gradually increase
to a higher speed. This prevents cold air from blowing
into the passenger compartment. If you want the fan at a
high speed, press the up arrow button until you reach the
highest position of the display. If you want the fan at a
low speed, press the down arrow button until the lowest
position is displayed.
ON/OFF: Press this button to turn the system on or off.
Turning the climate control system on in this way will
recall all previous manually set mode settings. If the system is turned on by pushing the driver's
TEMP/AUTO knob for automatic operation, all of the
previous manually set mode settings will be changed
back to the fully automatic mode.
AC: Press this button to turn the air conditioning on and
off. The system will cool and dehumidify the air inside
the vehicle. In the automatic operation mode, the display
will show AC OFF when the air conditioning has been
turned off.
RECIRCULATION: Press this button to limit
the amount of outside air entering your vehicle.
This is helpful to limit odors entering your vehicle.
In the automatic operation mode, the system will
use recirculation as necessary to cool the air.
Pressing the recirculation button will change the
operation to a manual mode and the air will recirculate
non
-stop. Press this button again to turn off the
recirculation feature.
If you notice the windows fogging, press the
recirculation button to exit the recirculation mode.