2001 AUDI A4 manual

37-6

Tiptronic shift mechanism, removing
and installing


Removing

- Shift selector lever into position "P".

- Note radio code (for vehicles equipped with
coded anti-theft radio).

- Disconnect Ground (GND) strap from battery.

- Selector lever handle, removing page 37
-
22
.

- Remove shift mechanism cover page 37
-
24
.

- Raise vehicle.

- Disconnect front exhaust pipes with catalytic
converter from the rear exhaust system and tie
them up on side.

Repair Manual, Engine Mechanical, Repair
Group 26, removing and installing exhaust
system.
Pa
ge 8 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-10

- Attach cover.

All-wheel-drive vehicles
Continuation for all vehicles
Repair Manual, Engine Mechanical, Repair Group 26; removing and
installing exhaust system. - Tighten nuts (arrows, 4 pieces) to 10 Nm.
- Check adjustment of selector lever cable and adjust if necessary
page 37
-45
.
- Ignition key removal lock, checking page 37
-1 .
- Bolt driveshaft to transmission flange page 39
-79
, Driveshaft,
removing and installing.
- Install heat shield.
- Connecting front exhaust pipe to rear exhaust system.- Installing shift mechanism cover page 37
-24
.
- Selector lever handle, installing page 37
-22
.
- Connect battery Ground (GND) strap.
- For vehicles equipped with coded anti-theft radio, activate code.
- Check shift mechanism page 37
-2 .
Pa
ge 13 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-16


Repair Manual, 5 Spd. Automatic Transmission
01V On Board Diagnostic (OBD), Repair Group 01; Performing On Board Diagnostic (OBD)
18 -
Pivot pin
Secures cable lever - 12 - in shift
mechanism housing - 17 -
19 -
Locking latch For shift lock solenoidRemoving and installing Page 37
-32

onward
20 -
Shift Lock Solenoid -N110-
Removing and installing Page 37
-32

onward
Can be checked via electrical test and read
measuring value block
Pa
ge 19 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-24

Cover for Tiptronic shift mechanism,
removing and installing


Removing:

- Remove cover of center console above shift
mechanism.

Repair Manual, Body Interior, Repair Group
68; Storage compartments, covers and trim; Center console, removing.


- Selector lever handle, removing page 37
-
22
.

- Shift selector lever into position "P" by pulling
pull rod.

- Switch off ignition.
Pa
ge 27 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-30


Tiptronic Switch -F189-, removing and
installing

Installation location:
The Tiptronic switch is integrated into the upper
cover -1- of shift mechanism.
Repair Manual, 5 Spd. Automatic Transmission
01V On Board Diagnostic (OBD), Repair Group 01; Performing On Board Diagnostic (OBD)
- For occurring malfunctions, the Tiptronic switch
must be checked for interference in Measuring
Value Block and in the electrical test. Tiptronic
switch must only be replaced after wiring test.
For vehicles with Tiptronic sport steering wheel,
the buttons at steering wheel and their wire
connections must be checked. Pa
ge 33 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-40

Selector lever cable for Tiptronic shift
mechanism, removing and installing


Special tools and equipment

Removing
Repair Manual, Engine Mechanical, Repair Group 26, removing and
installing exhaust system
80-200 Pry lever
- Shift selector lever into position "P".
- Raise vehicle.
- Remove crossmember below exhaust system if installed.
- Disconnect front exhaust pipes with catalytic converter from the rear
exhaust system and tie them up on side;
Pa
ge 45 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-44


All-wheel-drive vehicles
Continuation for all vehicles
Repair Manual, Engine Mechanical, Repair Group 26, removing and
installing exhaust system.
Tightening torques - Tighten nuts (arrows, 4 pieces) to 10 Nm.
- Check adjustment of selector lever cable and adjust if necessary
page 37
-45
.
- Install heat shield.
- Bolt driveshaft to transmission flange page 39
-79
, Driveshaft,
removing and installing.
- Connecting front exhaust pipe to rear exhaust system:- Install front crossmember below exhaust system.
Bracket/selector lever cable to transmission 23 Nm
Selector lever cable to mounting bracket 12 Nm
Pa
ge 49 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1

37-47


Locking cable for Tiptronic shift
mechanism, removing and installing

Removing
Repair Manual, Body Interior, Repair Group 68;
storage compartments/covers; front center console, removing and installing
- Shift selector lever into position "2".
- Note radio code (for vehicles equipped with
coded anti-theft radio).
- Disconnect Ground (GND) strap from battery.
- Selector lever handle, removing page 37
-22
- Front center console, removing
Pa
ge 52 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1