2001 Acura RL check engine

Owner Maintenance Checks
You should check the following items at the specified intervals. If
you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every
time you fill the fuel tank. See page 171.
Engine coolant level — Check the
radiator reserve tank every time
you fill the fuel tank. See page 172 .

Windshield washer fluid — Check the level in the reservoir monthly.
If weather conditions cause you to
use the washers frequently, check
the reservoir each time you stop
for fuel. See page 227 . Automatic transmission — Check
the fluid level monthly. See page
228.
Brakes — Check the fluid level
monthly. See page 230 . Tires — Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page
245.

Lights — Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate lights monthly. See

page 250.

Maintenance

Engine Oil
Adding Oil
To add oil, unscrew and remove the engine oil fill cap on top of the left
valve cover. Pour in the oil, and replace the engine oil fill cap.
Tighten it securely. Wait a few minutes and recheck the oil level. Do
not fill above the upper mark; you
could damage the engine. Recommended Oil
Oil is major contributor to your
engine's performance and longevity.
Always use a premium-grade detergent oil displaying the API
Certification Seal. This seal indicates
the oil is energy conserving, and that
it meets the American Petroleum
Institute's latest requirements. It is
highly recommended that you use Honda Motor Oil in your vehicle for
as long as you own it. Make sure the API Certification Seal
says "For Gasoline Engines."
API CERTIFICATION SEAL
CONTINUED

Maintenance

ENGINE OIL FILL CAP

Engine Oil

4. Install a new oil filter according to
instructions that come with it.

5. Put a new washer on the drain bolt,

then reinstall the drain bolt.
Tighten it to:
33 lbf.ft (44 N.m , 4.5 kgf.m)

6. Refill the engine with the recom-

mended oil.
Engine oil change capacity
(including filter):
4.9 US qt (4.6 , 4.0 Imp qt)

7. Replace the engine oil fill cap.

Start the engine. The oil pressure
indicator light should go out within
five seconds. If it does not, turn off
the engine and reinspect your
work.

8. Let the engine run for several

minutes and check the drain bolt
and oil filter for leaks.

9. Turn off the engine, let it sit for

several minutes, then check the oil
level. If necessary, add oil to bring the level to the upper mark on the
dipstick.

Improper disposal of engine oil can be
harmful to the environment. If you
change your own oil, please dispose ofthe used oil properly. Put it in a sealed
container and take it to a recycling center. Do not discard it in a trash bin
or dump it on the ground.
Maintenance
NOTICE

Cooling System

Adding Engine Coolant
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and
50 percent water. Never add straight
antifreeze or plain water.
Always use Honda All Season
Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 percent
antifreeze and 50 percent water. It
does not require any additional

mixing.

If it is not available, you may use
another major-brand non-silicate
coolant as a temporary replacement.
Make sure it is a high-quality coolant
recommended for aluminum engines.
However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling system to malfunction or fail. Have
the cooling system flushed and
refilled with Honda antifreeze/ coolant as soon as possible.
If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
1. Make sure the engine and radiator
are cool.

CONTINUED

Maintenance
RESERVE TANK

Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Cooling System

11.Fill the reserve tank to the MAX
mark. Install the reserve tank cap.

12.Check the level in the radiator,

add coolant if needed.

13.Install the engine cover. First

tighten the two bolts on the front of the engine cover, then tighten
the three nuts on the engine cover.
Tightening torque:
7 lbf .
ft (10 N .
m , 1.0 kgf .
m)

14.Install the radiator cap, and

tighten it to the first stop.

15.Start the engine and let it run until

the radiator cooling fan comes on
at least twice. Then stop the
engine.

16.Remove the radiator cap. Pour

coolant into the. radiator up to the base of the filler neck and into the
reserve tank up to the MAX mark.

17.Start the engine and hold it at

1,500 rpm until the cooling fan comes on. Turn off the engine.
Check the coolant level in the
radiator and add coolant if needed.

18.Install the radiator cap, and

tighten it fully.

19.If necessary, fill the reserve tank

to the MAX mark. Install the
reserve tank cap.

Maintenance

Fill up to here
FILLER NECK
RESERVE TANK

Windshield Washers

Check the level in the windshield
washer reservoir at least monthly during normal usage. In bad weather,
when you use the washers often, check the level every time you stop

for fuel.

The windshield washer reservoir is located behind the driver's side

headlight.

Check the reservoir's fluid level by
removing the cap and looking at the
float. It should be up to the top of the neck. If the float is at the bottom of
the neck, the reservoir is nearly
empty.
Fill the reservoir with a good-quality
windshield washer fluid. This increases the cleaning capability and
prevents freezing in cold weather.

Do not use engine antifreeze or a
vinegar/water solution in the
windshield washer reservoir.
Antifreeze can damage your ear's paint, while a vinegar/water solution can
damage the windshield washer pump.
Use only commercially-available
windshield washer fluid.

When you refill the reservoir, clean the edges of the windshield wiper
blades with windshield washer fluidon a clean cloth. This will help to
condition the blade edges.

Maintenance

FLOAT

NOTICE

Automatic Transmission Fluid

Check the fluid level with the engine
at normal operating temperature.
1. Park the car on level ground. Shut
off the engine.

2. Remove the dipstick (yellow loop)

from the transmission and wipe it
with a clean cloth.

3. Insert the dipstick into the

transmission. Make sure the notch
in the rubber cap fits in thedipstick guide and that you push
the dipstick in all the way.

4. Remove the dipstick and check

the fluid level. It should be
between the upper and lower
marks.

5. If the level is below the lower

mark, add fluid into the tube to
bring it to the upper mark. Always
use Honda ATF-Z1 (Automatic
Transmission Fluid). If it is not available, you may use a
DEXRON
® III automatic
transmission fluid as a temporary
replacement. However, continued
use can affect shift quality. Have
the transmission flushed and refilled with Honda ATF-Z1 assoon as it is convenient.

To thoroughly flush the
transmission, the technician should drain and refill it with
Honda ATF-Z1 (Automatic
Transmission Fluid), then drive the vehicle a short distance. Do
this three times. Then drain and
refill the transmission a final time.
Maintenance

DIPSTICK GUIDE

DIPSTICK

UPPER MARKLOWER MARK

Brake Fluid, Power Steering

Brake Fluid

Check the fluid level in the brake
fluid reservoir monthly.
The brake fluid should be replaced according to the time recommenda-
tion in the maintenance schedule.
Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 fluid, from a sealed
container, as a temporary
replacement. However, the use of any non-Honda brake fluid can cause
corrosion and decrease the life of the
system. Have the brake system
flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 assoon as possible.
Brake fluid marked DOT 5 is not
compatible with your car's braking system and can cause extensive

damage.
Brake System
The fluid level should be between the MIN and MAX marks on the side
of the reservoir. If the level is at or
below the MIN mark, your brake system needs attention. Have the
brake system inspected for leaks or
worn brake pads. Power Steering
You should check the fluid level in the power steering reservoir at leastonce a year. Check the level when
the engine is cold. Look at the side of the reservoir. The fluid should be
between the UPPER LEVEL and LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
fluid to the UPPER LEVEL.

Maintenance
MAX
MIN
UPPER

LEVEL
LOWER

LEVEL