2001 Acura CL battery

The engine can be severely damaged
if this light f lashes or stays on when
the engine is running. For complete
inf ormation, see page .
If this light comes on when the
engine is running, the battery is not
being charged. For complete
inf ormation, see page .This light has two f unctions:
Itcomesonwhenyouturnthe
ignition switch ON (II) as a
reminder to check the parking
brake. If the parking brake is not
set, it goes of f af ter the engine
starts. If the parking brake is set,
it goes of f when you release the
parking brake with the engine
running. Driving with the parking
brake applied can damage the
brakes and tires.
If the indicator remains lit after
you have f ully released the
parking brake while the engine is
running, or if it comes on while
driving, it can indicate a problem
in the brake system. For complete
inf ormation, see page .
See page . This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II), and when
the ignition switch is turned to
START (III). If this light comes on at
any other time, there is a problem in
theABS.If thishappens,takethe
cartoyourdealertohaveitchecked.
With the light on, your car still has
normal braking ability but no anti-
lock. For complete inf ormation, see
page .
1.
2.
284
285
287187
286
Indicator L ights
Inst rument s and Cont rols
L ow Oil Pressure
Indicator
Charging System
Indicator Parking Brake and Brake System
Indicator
Malf unction Indicator
Lamp Anti-lock Brake
System (A BS)
Indicator
55
U.S. Canada
U.S. Canada

The odometer shows the total dis-
tance your car has been driven. It
measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.The trip meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays by pressing the Select
button repeatedly. Each trip meter
works independently, so you can
keep track of two dif f erent distances.
When you turn the ignition switch
ON (II), what you last selected is
displayed.
To reset a trip meter, display it and
then press and hold the Reset button
until the number resets to ‘‘0.0’’. You
will hear a beep. Both trip meters
will reset if the car’s battery goes
dead or is disconnected.
Gauges
Inst rument s and Cont rols
Odometer T rip Meter
61
S SEEL
LEE C
CT T
B
BU UT TT
TO
ON N
R
RE ES
SE ET
T
B
BU UT TT
TO
ON N

´
Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors, and the
LED will get dim. Replace the
battery as soon as possible.
Battery type: CR2025To replace the battery, remove the
round cover on the back of the trans-
mitter by turning it counterclockwise
with a coin.
Remove the old battery and note the
polarity. Make sure the polarity of
the new battery is the same ( side
f acing up), then insert it in the
transmitter.
Keys and Locks
Inst rument s and Cont rols
Panic Mode
Replacing t he Bat t ery
84
C Clloo s
see
O
Op
pe
enn R
RO
OU UNNDD
C
CO OV VE
ER
R
B
BA A T
TT
TE
ER
RY Y

The HomeLink Universal
Transmitter built into your car can
be programmed to operate remotely-
controlled devices around your home,
such as garage doors, lighting, or
home security systems. It can
replaceuptothreeremote
transmitters.
If you have problems with training
the HomeLink Universal
Transmitter, or would like
inf ormation on home products that
can be operated by the transmitter,
call (800) 355-3515. On the Internet,
go to www.homelink.jci.com.Always ref er to the operating
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with the HomeLink
Universal Transmitter. If you do not
have this inf ormation, you should
contact the manuf acturer of the
equipment.
While training or using the
transmitter, make sure you have a
clear view of the garage door or gate,
and that no one will be injured by its
movement.
If your garage door opener was
manuf actured bef ore April 1982, you
may not be able to program the
HomeLink Universal Transmitter to
operate it. Garage door openers
manufactured before that date do
not have a safety feature that causes
them to stop and reverse if an
obstacle is detected during closing,
increasing the risk of injury. If you
have questions, call (800) 355-3515. If you are training the transmitter to
operate a garage door or gate, it is
recommended that you unplug the
motor f or that device during training.
Repeatedly pressing the remote
control button could burn out the
motor.
The HomeLink transmitter stores
the code in a permanent memory.
There should be no need to retrain
the transmitter if your car’s battery
goes dead or is disconnected.
Customer Assistance Important Saf ety Precautions General Inf ormation
HomeL ink Universal T ransmitter
Inst rument s and Cont rols89

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
You can select memorized positions
as f ollows.Make sure the parking brake is set
and the shif t lever is in Park.
Readjusting the seat position.
Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.The system will move the seat and
outside mirrors to the memorized
positions. The indicator light in the
selected memory button will f lash
during movement. When the
adjustments are complete, you will
hear two beeps and the indicator
light will remain on.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your car’s battery goes dead or
is disconnected. 1.
2.Select ing a Memorized Posit ion
Driving Posit ion Memory Syst em
Inst rument s and Cont rols104
M M
E
EM
M O
ORRYY B
BUUT TT
TO
ON NSS

Follow these precautions whenever
you use the seat heaters:Use the HI setting only to heat the
seats quickly. Select the LO
setting when the seats f eel warm.
The HI setting draws large
amounts of current f rom the
battery.
Do not use the seat heaters, even
on the LO setting, if the engine is
lef t idling f or an extended period.
They can weaken the battery,
causing hard starting.
The HI or LO indicator lights and
remains lit until you turn it of f by
pushing the opposite side of the
switch lightly. The indicator will turn
off.
In HI, the heater turns of f when the
seat gets warm, and turns back on
after the seat’s temperature drops. It
continues to cycle as long as you
leave it set on HI. The HI indicator
remains lit as a reminder that you
have the heater on.
In LO, the heater runs continuously.
It does not cycle with temperature
changes.
Because of the sensors f or the side
airbag system, there is no heater in
the passenger’s seat-back.
Both f ront seats are equipped with
seat heaters. The ignition switch
must be ON (II) to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
select LO by pushing the back of the
switch. This will keep the seat warm.
Seat Heaters
Inst rument s and Cont rols106
S SE
EA
A T
T H
HE
EA
A T
TE
ER
RS S

Î
Î
Your Acura’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The cassette system f eatures Dolby
B noise reduction, automatic
sensing of chromium-dioxide (CrO )
tape, and autoreverse f or continuous
play.The anti-thef t f eature will disable the
system if it is disconnected f rom the
car’s battery. To get the system
working again, you must enter a
code number (see page ).
The in-dash CD changer holds up to
six discs. You operate the CD
changer with the same controls used
f or the radio. See page f or CD
changer operation.
157
147
2
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Audio System
Comf ort and Convenience Feat ures
A M/FM/Cassette/CD Changer
Audio System
135

µThe preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed.
Once a station’s frequency is stored,
simply press and release the proper
Preset button to tune to it.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM. Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep. Use the TUNE or SEEK f unction
to tune the radio to a desired
station. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each Preset
button.
To store a f requency: You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
1.
2.
3.
4.
CONT INUED
Audio System
Comf ort and Convenience Feat ures
Preset
137
P P W
WR R//V
V O
OL L
K
KN NO OBB S
ST
TE
ER
RE EO
O
I
IN ND DI
ICCA A T
TO
OR R T
T
U
UN NEE K
KNNO OBB
S
SC CAA N
N B
BUUT TT
TO
ON N S
SEEE
EK
K B
BUUT TT
TO
ON NSS
P
P R
RE ES
SE ET
T B
BUUT TT
TO
ON NSS
F
FM
M
B
BU UT TT
TO
ON N
A
A
M
M
B
BU UT TT
TO
ON N