2000 YAMAHA YZF-R6 brake pads

6
PERIODIC MAINTENANCE AND MINOR REPAIR
Tool kit................................................................... 6-1
Periodic maintenance and lubrication ................... 6-3
Cowling and panel removal and installation.......... 6-6
Cowlings A and B ................................................. 6-6
Panel C ................................................................. 6-8
Spark plug inspection ........................................... 6-9
Engine oil ............................................................ 6-10
Cooling system ................................................... 6-13
Changing the coolant .......................................... 6-14
Air filter ............................................................... 6-17
Air intake duct ..................................................... 6-19
Carburetor adjustment ........................................ 6-20
Idle speed adjustment ........................................ 6-20
Throttle cable free play inspection ...................... 6-21
Valve clearance adjustment ................................ 6-21
Tires .................................................................... 6-21
Wheels ................................................................ 6-24
Clutch lever free play adjustment........................ 6-25
Brake light switch adjustment ............................. 6-25
Checking the front and rear brake pads.............. 6-26
Inspecting the brake fluid level............................ 6-27
Brake fluid replacement ...................................... 6-28
Drive chain slack check ...................................... 6-28Drive chain slack adjustment ............................. 6-29
Drive chain lubrication........................................ 6-29
Cable inspection and lubrication ........................ 6-30
Throttle cable and grip lubrication ...................... 6-30
Brake pedal lubrication....................................... 6-30
Brake and clutch lever lubrication ...................... 6-31
Sidestand lubrication.......................................... 6-31
Rear suspension lubrication............................... 6-31
Front fork inspection ........................................... 6-32
Steering inspection ............................................ 6-32
Wheel bearings .................................................. 6-33
Battery................................................................ 6-33
Fuse replacement .............................................. 6-34
Headlight bulb replacement ............................... 6-35
Tail/brake light bulb replacement ........................ 6-36
Turn signal light bulb replacement...................... 6-36
Supporting the motorcycle ................................. 6-37
Front wheel removal ........................................... 6-37
Front wheel installation ...................................... 6-38
Rear wheel removal ........................................... 6-39
Rear wheel installation ....................................... 6-40
Troubleshooting .................................................. 6-40
Troubleshooting chart ......................................... 6-41
E_5eb_PeriodicTOC.fm Page 1 Thursday, November 18, 1999 4:06 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
6
EAU00473
PERIODIC MAINTENANCE AND LUBRICATION
CP-01ENO. ITEM CHECKS AND MAINTENANCE JOBSINITIAL
(1,000 km)EVERY
6,000 km
or
6 months
(whichever
comes first)12,000 km
or
12 months
(whichever
comes first)
1
*Fuel line• Check fuel hoses for cracks or damage.
• Replace if necessary.ÖÖ
2*Fuel filter• Check condition.
• Replace if necessary.Ö
3 Spark plugs• Check condition.
• Clean, regap or replace if necessary.ÖÖÖ
4*Valves• Check valve clearance.
• Adjust if necessary.Every 42,000 km or 42 months
(whichever comes first)
5 Air filter• Replace if necessary.ÖÖ
6Clutch• Check operation.
• Adjust or replace cable.ÖÖÖ
7*Front brake• Check operation, fluid level and vehicle for fluid leakage.
(See NOTE on page 6-5.)
• Correct accordingly.
• Replace brake pads if necessary.ÖÖÖ
8*Rear brake• Check operation, fluid level and vehicle for fluid leakage.
(See NOTE on page 6-5.)
• Correct accordingly.
• Replace brake pads if necessary.ÖÖÖ
9*Wheels• Check balance, runout and for damage.
• Rebalance or replace if necessary.ÖÖ
E_5eb_Periodic.fm Page 3 Thursday, November 18, 1999 4:06 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-26
6
EAU00721
Checking the front and rear
brake pads
EAU00725
Front brake
A wear indicator groove is provided on
each brake pad. This indicator allows
checking of brake pad wear without
disassembling the brake. Inspect the
groove. If the groove has almost disap-
peared, ask a Yamaha dealer to re-
place the pads.
EAU01641
Rear brake
A wear indicator groove is provided on
each brake pad. This indicator allows
checking of brake pad wear without
disassembling the brake. Remove the
rear caliper bolt and tilt the caliper for-
ward. Inspect the groove. If the groove has
almost disappeared, ask a Yamaha
dealer to replace the pads. Install the
caliper and caliper bolt, then tighten the
bolt to the specified torque.
1. Wear indicator groove
1. Caliper bolt
1. Wear indicator grooveTightening torque:
Caliper bolt:
40 Nm (4.0 m·kg)
E_5eb_Periodic.fm Page 26 Thursday, November 18, 1999 4:06 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-38
6 3. Elevate the front wheel.
4. Remove the brake hose holders
and calipers.
NOTE:@ Do not depress the brake lever when
the calipers are off the discs as the
brake pads will be forced shut. @5. Pull out the wheel axle and re-
move the wheel by pulling it back-
wards.
EAU01638
Front wheel installation1. Lift up the wheel between the front
fork legs.
2. Install the wheel axle and let the
motorcycle down.
3. Push down hard on the handle-
bars several times to check for
proper fork operation.
4. Install the calipers, caliper bolts
and brake hose holders. Make
sure there is enough gap between
the brake pads before installing
the calipers onto the brake discs.
5. Tighten the wheel axle, pinch bolt
and caliper bolts to the specified
torques.
1. Brake hose holder bolt
2. Caliper bolt (´ 2)
Tightening torque:
Wheel axle:
72 Nm (7.2 m·kg)
Pinch bolt:
20 Nm (2.0 m·kg)
Caliper bolt:
40 Nm (4.0 m·kg)
E_5eb_Periodic.fm Page 38 Thursday, November 18, 1999 4:06 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-39
6
EAU01247
Rear wheel removal
EW000122
WARNING
@ l
It is advisable to have a Yamaha
dealer service the wheel.
l
Securely support the motor-
cycle so there is no danger of it
falling over.
@1. Loosen the axle nut and caliper
bolts.
2. Elevate the rear wheel.3. Remove the axle nut, caliper bolts
and caliper.
4. Loosen the locknuts on each side
of the swingarm.
5. Turn the chain adjusting bolts fully
inward.
6. Push the wheel forward and re-
move the drive chain.
7. Pull out the wheel axle and re-
move the wheel assembly by pull-
ing backwards.
NOTE:@ l
Do not depress the brake pedal
when the caliper is off the disc as
the brake pads will be forced shut.
l
You do not have to disassemble
the chain in order to remove or in-
stall the rear wheel.
@
1. Axle nut
2. Adjusting bolt
3. Locknut
1. Caliper bolt (´ 2)
E_5eb_Periodic.fm Page 39 Thursday, November 18, 1999 4:06 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-40
6
EAU01246
Rear wheel installation1. Install the wheel assembly and in-
sert the axle.
2. Install and adjust the drive chain.
(See page 6-28 for details about
adjusting the drive chain slack.)
3. Install the axle nut and let the
motorcycle down.
4. Install the caliper and caliper bolts.
Make sure there is enough gap
between the brake pads before in-
stalling the caliper onto the brake
disc.
5. Tighten the axle nut and caliper
bolts to the specified torques.
EAU01008
TroubleshootingAlthough Yamaha motorcycles receive
a rigid inspection before shipment from
the factory, trouble may occur during
operation.
Any problem in the fuel, compression,
or ignition systems can cause poor
starting and loss of power. The trouble-
shooting chart describes a quick, easy
procedure for making checks.
If your motorcycle requires any repair,
bring it to a Yamaha dealer. The skilled
technicians at a Yamaha dealership
have the tools, experience, and know-
how to properly service your motor-
cycle. Use only genuine Yamaha parts
on your motorcycle. Imitation parts may
look like Yamaha parts, but they are of-
ten inferior. Consequently, they have a
shorter service life and can lead to ex-
pensive repair bills. Tightening torque:
Axle nut:
150 Nm (15.0 m·kg)
Caliper bolt:
40 Nm (4.0 m·kg)
E_5eb_Periodic.fm Page 40 Thursday, November 18, 1999 4:06 PM

10-INDEXAAir filter .................................................. 6-17
Air intake duct ........................................ 6-19
Antitheft alarm (optional) ........................ 3-12BBattery ................................................... 6-33
Brake and clutch lever lubrication........... 6-31
Brake fluid replacement ......................... 6-28
Brake light switch adjustment ................. 6-25
Brake pedal lubrication........................... 6-30CCable inspection and lubrication ............ 6-30
Carburetor adjustment ........................... 6-20
Care.........................................................7-1
Changing the coolant ............................. 6-14
Checking the front and rear brake
pads .................................................... 6-26
Clutch lever ............................................ 3-11
Clutch lever free play adjustment ........... 6-25
Controls/Instruments ................................2-3
Cooling system ...................................... 6-13
Cowling and panel removal and
installation .............................................6-6
Cowlings A and B ....................................6-6DDiagnosis device......................................3-9
Digital speedometer .................................3-7
Dimmer switch .........................................3-9
Drive chain lubrication ............................ 6-29
Drive chain slack adjustment.................. 6-29
Drive chain slack check.......................... 6-28
EEngine break-in ....................................... 5-5
Engine oil .............................................. 6-10
Engine stop switch................................. 3-10FFront brake lever ................................... 3-11
Front fork adjustment............................. 3-17
Front fork inspection .............................. 6-32
Front wheel installation .......................... 6-38
Front wheel removal .............................. 6-37
Fuel ....................................................... 3-13
Fuel indicator light ................................... 3-2
Fuel indicator light circuit check ............... 3-6
Fuel tank breather hose ......................... 3-14
Fuel tank cap ......................................... 3-13
Fuse replacement.................................. 6-34GGive safety the right of way ..................... 1-1HHandlebar switches ................................. 3-9
Dimmer switch ................................... 3-9
Engine stop switch ........................... 3-10
Horn switch ...................................... 3-10
Light switch ...................................... 3-10
Pass switch ........................................ 3-9
Start switch ...................................... 3-10
Turn signal switch ............................ 3-10
Headlight bulb replacement ................... 6-35
Helmet holder ........................................ 3-17
High beam indicator light ......................... 3-2
Horn switch ........................................... 3-10
IIdentification number records ...................9-1
Idle speed adjustment ............................6-20
Indicator lights ..........................................3-2
Fuel indicator light...............................3-2
High beam indicator light ....................3-2
Neutral indicator light ..........................3-2
Oil level/coolant temperature
indicator light....................................3-3
Turn indicator light ..............................3-2
Inspecting the brake fluid level ...............6-27KKey identification number .........................9-1LLeft view...................................................2-1
Light switch ............................................3-10
Luggage strap holders ...........................3-23MMain switch/Steering lock .........................3-1
Model label ..............................................9-2NNeutral indicator light ...............................3-2OOil level/coolant temperature indicator
light ........................................................3-3
Oil level / coolant temperature indicator
light circuit check ...................................3-5PPanel C ....................................................6-8
Parking.....................................................5-5
E_5ebIX.fm Page 1 Thursday, November 18, 1999 4:09 PM