2000 YAMAHA XV125S service

1
2
3
4
5
6
7
8
9
6-24
PERIODIC MAINTENANCE AND MINOR REPAIR
8Brake fluid may deteriorate
painted surfaces or plastic
parts. Always clean up spilled
fluid immediately.
8Have a Yamaha dealer check
the cause if the brake fluid
level goes down.EAU00742Brake fluid replacement
The brake fluid should be replaced
only by trained Yamaha service
personnel. Have the Yamaha deal-
er replace the following compo-
nents during periodic maintenance
or when they are damaged or leak-
ing:
8oil seals (every two years)
8brake hoses (every four years)
EAU00744Drive chain slack check
NOTE:
Spin the wheel several times and
find the tightest position of the
chain. Check and/or adjust the
chain slack while it’s in this tightest
position.
To check the chain slack the motor-
cycle must be held straight up with
both wheels on the ground and
without rider. Check the slack at
the position shown in the illustra-
tion. Normal slack is approximately
30 ~ 40 mm. If the slack exceeds
40 mm, adjust.
a. Chain slack
a
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 55

1
2
3
4
5
6
7
8
9
6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
7. Adjust the free play in the
brake pedal.
EW000103
w
Check the operation of the brake
light after adjusting the rear brake.
1
6. Insert a new cotter pin into the
axle nut and bend the end of
the cotter pin as shown. If the
notch in the axle nut and the
cotter pin hole do not match,
tighten the nut slightly to align
them.
EW000110
w
Always use a new cotter pin on
the axle nut.
1. Cotter pin
EAU00769Drive chain lubrication
The chain consists of many parts
which work with each other. If the
chain is not maintained properly, it
will wear out quickly. Therefore,
the chain must be serviced regular-
ly. This service is especially neces-
sary when riding in dusty areas.
This motorcycle is equipped with a
sealed type chain. Steam cleaning,
high-pressure washes, and sol-
vents can damage chain so do not
use these for cleaning it. Use only
kerosene to clean the drive chain.
Wipe it dry, and thoroughly lubri-
cate it with SAE 30 ~ 50W motor
oil. Do not use any other lubricants
on the drive chain. They may con-
tain solvents that could damage
the sealed chain.
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 57

1
2
3
4
5
6
7
8
9
6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU00862Supporting the motorcycle
Since the Yamaha XV125S has no
centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other
maintenance requiring the motor-
cycle to stand upright.
Front wheel service
To stabilize the rear of the motor-
cycle, either use a motorcycle
stand or place a motorcycle jack
under the frame in front of the rear
wheel to prevent it from moving
from side to side. Then use a
motorcycle stand to elevate the
front wheel off of the ground.Rear wheel service
Use a motorcycle stand or motor-
cycle jack to elevate the motorcycle
so the rear wheel is off the ground.
Alternatively, two jacks can be
placed under the frame or
swingarm.
Check that the motorcycle is in a
stable and level position before
starting any maintenance. A strong
wooden box can be placed under
the engine for added stability.
1
EAU00894Front wheel removalEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Remove the speedometer
cable from the front wheel
side.
1. Speedometer cable
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 67

1
2
3
4
5
6
7
8
9
6-38
PERIODIC MAINTENANCE AND MINOR REPAIR
5. Push down hard on the han-
dlebars several times to check
for proper fork operation.
6. Tightening the wheel axle to
the specified torque.
7. Install the pinch bolts and
tighten them to the specified
torque.
8. Install the speedometer cable.EAU01550Rear wheel removalEW000122
w
8It is advisable to have a
Yamaha dealer service the
wheel.
8Securely support the motorcy-
cle so there is no danger of it
falling over.
1. Remove the axle nut cotter pin
and brake torque rod cotter
pin. Tightening torque:
Wheel axle:
59 Nm (5.9 m·kg)
Pinch bolt:
20 Nm (2.0 m·kg)
1
3 4
2
5
2. Loosen the axle nut and brake
torque nut.
3. Elevate the rear wheel by plac-
ing a suitable stand under the
engine.
4. Remove the brake torque rod
nut and bolt from the brake
shoe plate.
1. Brake torque rod
2. Brake torque rod cotter pin
3. Brake torque rod nut
4. Brake rod
5. Rear brake pedal free play adjusting nut
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 69

1
2
3
4
5
6
7
8
9
6-40
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU01008Troubleshooting
Although Yamaha motorcycles
receive a rigid inspection before
shipment from the factory, trouble
may occur during operation.
Any problem in the fuel, compres-
sion, or ignition systems can cause
poor starting and loss of power.
The troubleshooting chart
describes a quick, easy procedure
for making checks.
If your motorcycle requires any
repair, bring it to a Yamaha dealer.
The skilled technicians at a
Yamaha dealership have the tools,
experience, and know-how to
properly service your motorcycle.
Use only genuine Yamaha parts on
your motorcycle. Imitation parts
may look like Yamaha parts, but
they are often inferior.
Consequently, they have a shorter
service life and can lead to expen-
sive repair bills.
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 71

1
2
3
4
5
6
7
8
9
EAU01038
SPECIFICATIONS
Specifications
Model XV125S
Dimensions
Overall length 2,190 mm
Overall width 805 mm
Overall height 1,140 mm
Seat height 685 mm
Wheel base 1,495 mm
Ground clearance 145 mm
Minimum turning radius 2,800 mm
Basic weight (with oil and full
fuel tank)147 kg
Engine
Engine type Air-cooled 4-stroke, SOHC,
gasoline
Cylinder arrangement V-type 2-cylinder
Displacement 124 cm
3
Bore ´Stroke 41.0 ´47.0 mm
Compression ratio 10.7:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Type
Recommended engine oil
classification API Service SE, SF, SG type
or higher
cC
Be sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled “Energy
Conserving”) contain anti-friction additives which will cause
clutch and/or starter clutch slippage, resulting in reduced
component life and poor engine performance.
Quantity
Periodic oil change 1.4 L
With oil filter replacement 1.6 L
Total amount 1.7 L
Air filterWet type element
8-1
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
5AJ-9-E3 (XV125S)<3.1E> 4/5/0 5:01 PM Page 78