2000 YAMAHA XJR 1300 drain bolt

PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
6 2. With the engine stopped, check
the oil level through the level win-
dow located at the lower part of
the right side crankcase cover.
NOTE:@ Wait a few minutes until the oil level
settles before checking. @3. The oil level should be between
the maximum and minimum level
marks. If the level is low, add suffi-
cient oil to raise it to the specified
level.Engine oil and oil filter element re-
placement
1. Warm up the engine for several
minutes.
2. Stop the engine. Place an oil pan
under the engine and remove the
oil filler cap.
3. Remove the drain bolt and drain
the oil.4. Remove the oil filter drain screw,
filter cover bolt, filter cover, oil filter
element and O-ring.
5. Reinstall the drain bolt and tighten
it to the specified torque.1. Oil level window
2. Maximum level mark
3. Minimum level mark
1. Engine oil drain bolt
1. Oil filter drain screw
2. Oil filter cover boltTightening torque:
Drain bolt:
43 Nm (4.3 m·kg)

PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
66. Install the new oil filter element
and O-ring.7. Align the projection on the filter
cover with the slot in housing and
install the filter cover.
8. Tighten the oil filter bolt and oil fil-
ter drain screw to the specified
torque.
NOTE:@ Make sure the O-rings are seated prop-
erly. @
9. Fill engine with oil. Install the oil fill-
er cap and tighten.
EC000066
CAUTION:@ l
Do not put in any chemical addi-
tives. Engine oil also lubricates
the clutch and additives could
cause clutch slippage.
l
Be sure no foreign material en-
ters the crankcase.
@
1. Oil filter element
2. O-ring (´ 2)
1. Projection
2. Slot
Tightening torque:
Oil filter bolt:
15 Nm (1.5 m·kg)
Oil filter drain screw:
7 Nm (0.7 m·kg)
Recommended oil:
See page 8-1.
Oil quantity:
Total amount:
4.2 L
Periodic oil change:
3.0 L
With oil filter replacement:
3.35 L

MOTORCYCLE CARE AND STORAGE
7-4
7
ECA00013
CAUTION:@ l
Apply spray oil and wax spar-
ingly and wipe off any excess.
l
Never apply oil or wax on rub-
ber and plastic parts, but treat
them with a suitable care prod-
uct.
l
Avoid using abrasive polishing
compounds as they wear away
the paint.
@NOTE:@ Consult a Yamaha dealer for advice on
what products to use. @
StorageShort-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA00014
CAUTION:@ l
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp while it is still
wet will allow water and humidi-
ty to seep in and cause rust.
l
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
@
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Drain the carburetor float cham-
bers by loosening the drain bolts;
this will prevent fuel deposits from
building up. Pour the drained fuel
into the fuel tank.
3. Only for motorcycles equipped
with a fuel cock which has an
“OFF” position: Turn the fuel cock
to “OFF”.
4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
5. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.