2000 YAMAHA TW125 weight

6-16
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00652Tires
To ensure maximum performance,
long service and safe operation,
note the following:
Tire air pressure
Always check and adjust the tire
pressure before operating the
motorcycle.
EW000082
w
Tire inflation pressure should be
checked and adjusted when the
temperature of the tire equals the
ambient air temperature. Tire infla-
tion pressure must be adjusted
according to total weight of cargo,
rider, passenger, and accessories
(fairing, saddlebags, etc. if
approved for this model), and vehi-
cle speed.
EW000083
w
Proper loading of your motorcycle
is important for several character-
istics of your motorcycle, such as
handling, braking, performance
and safety. Do not carry loosely
packed items that can shift.
Securely pack your heaviest items
close to the center of the motorcy-
cle, and distribute the weight
evenly from side to side. Properly
adjust the suspension for your
load, and check the condition and
pressure of your tires. NEVER
OVERLOAD YOUR MOTORCYCLE.
Make sure the total weight of the
cargo, rider, passenger, and acces-
sories (fairing, saddlebags, etc. if
approved for this model) does not
exceed the maximum load of the
motorcycle. Operation of an over-
loaded motorcycle could cause tire
damage, an accident, or even
injury.
* Load is the total weight of cargo, rider, passen-
ger and accessories.
Maximum load* 180 kg
Cold tire pressure Front Rear
150 kPa 150 kPa
Up to 80 kg (1.50 kg/cm
2, (1.50 kg/cm2,1.50 bar) 1.50 bar)
80 kg load -150 kPa 175 kPa
Maximum load*(1.50 kg/cm
2, (1.75 kg/cm2,1.50 bar) 1.75 bar)
125 kPa 125 kPa
Off-road riding (1.25 kg/cm
2, (1.25 kg/cm2,
1.25 bar) 1.25 bar)
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 46

8-1
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Specifications
Model TW125
Dimensions
Overall length 2,140 mm
Overall width 810 mm
Overall height 1,120 mm
Seat height 805 mm
Wheelbase 1,330 mm
Ground clearance 260 mm
Minimum turning radius 2,100 mm
Basic weight (with oil and full
fuel tank)125 kg
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined
single cylinder
Displacement 124 cm
3
Bore ´Stroke 57.0 ´48.8 mm
Compression ratio 10:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Type
Recommended engine oil
classification API Service SE, SF, SG type
or higher
cC
Be sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled “Energy
Conserving”) contain anti-friction additives which will cause
clutch and/or starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity
Periodic oil change 1.0 L
With oil filter replacement 1.1 L
Total amount 1.3 L
Air filterWet type element
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 75

8-3
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Front150 kPa (1.50 kg/cm2, 1.50 bar)
Rear150 kPa (1.50 kg/cm2, 1.50 bar)
80 kg load ~ Maximum
load*
Front
150 kPa (1.50 kg/cm2, 1.50 bar)
Rear175 kPa (1.75 kg/cm2, 1.75 bar)
Off-road riding
Front
125 kPa (1.25 kg/cm2, 1.25 bar)
Rear125 kPa (1.25 kg/cm2, 1.25 bar)
*Load is total weight of cargo, rider, passenger and accessories.
Wheels
Front
Type Spoke wheel
Size 2.50 ´18
Rear
Type Spoke wheel
Size 14M/C ´MT4.50
Brakes
Front
Type Single disc brake
Operation Right hand operation
Fluid DOT 3 or DOT 4Rear
Type Drum brake
Operation Right foot operation
Suspension
Front
Type Telescopic fork
Rear
Type Swingarm (Monocross
suspension)
Shock absorber
Front Coil spring/oil damper
Rear Coil-gas spring/oil damper
Wheel travel
Front 160 mm
Rear 150 mm
Electrical
Ignition system C.D.I.
Charging system
Type C.D.I. magneto
Standard output 12 V, 11 A @ 5,000 rpm
Battery
Type GM7CZ-3D
Voltage, capacity 12 V, 7 AH
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 77

1
2
3
4
5
6
7
9
8-5
SPECIFICATIONS
8
EAU01064HOW TO USE THE CONVERSION TABLE
All specification data in this manual are listed in SI
and METRIC UNITS.
Use this table to convert METRIC unit data to
IMPERIAL unit data.
Ex.
METRIC MULTIPLIER IMPERIAL
** mm´0.03937 = ** in
2 mm´0.03937 = 0.08 inMETRIC TO IMPERIAL
Metric unit Multiplier Imperial unit
m • kg 7.233 ft • lb
Torquem • kg 86.794 in• lb
cm • kg 0.0723 ft • lb
cm • kg 0.8679 in • lb
Weightkg 2.205 lb
g 0.03527 oz
Speed km/hr 0.6214 mph
km 0.6214 mi
m 3.281 ft
Distance m 1.094 yd
cm 0.3937 in
mm 0.03937 in
cc (cm3) 0.03527 oz (IMP liq.)
Volume/ cc (cm3) 0.06102 cu • in
Capacity lt (liter) 0.8799 qt (IMP liq.)
lt (liter) 0.2199 gal (IMP liq.)
kg/mm 55.997 lb/in
Misc. kg/cm
214.2234 psi (lb/in2)Centigrade(°C)9/5 + 32Fahrenheit(°F)
CONVERSION TABLE
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 79