Page 44 of 86

6-12
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
2
2
EAU01501*Air filter
The air filter should be cleaned at
the specified intervals. It should be
cleaned more frequently when rid-
ing in unusually wet or dusty
areas.
Air filter element cleaning
1. Remove panel A. (See page
6-6 for removal and installa-
tion procedures.)
2. Remove the air filter case fit-
ting screws and the filter case
cover.
1. Air filter case cover
2. Screw (´4)EC000066
cC
8Do not put in any chemical
additives. Engine oil also lubri-
cates the clutch and additives
could cause clutch slippage.
8Be sure no foreign material
enters the crankcase.
10. Start the engine and warm up
for a few minutes. While
warming up, check for oil leak-
age. If oil leakage is found,
stop the engine immediately
and check for the cause.
EC000071
cC
Before reinstalling the oil drain
bolt, do not forget to install the O-
ring, compression spring, and oil
strainer in position.
9. Fill the engine with oil. Install
the oil filler cap and tighten. Tightening torque:
Drain bolt:
43 Nm (4.3 m·kg)
Filter cover screw:
7.0 Nm (0.7 m·kg)
Drain bolt (filter cover):
10 Nm (1.0 m·kg)
Recommended oil:
See page 8-1.
Total amount:
1.3 L
Periodic oil change:
1.0 L
With oil filter replacement:
1.1 L
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 42
Page 45 of 86

6-13
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9 3. Remove the air filter from the
case.
4. Remove the air filter element
from its frame and clean it
with solvent. After cleaning,
remove the remaining solvent
by squeezing the element.
5. Apply recommended oil to the
entire surface of the element
and squeeze out the excess oil.
The element should be wet but
not dripping.
1. Air filter element
2. Air filter element frame
6. Install the air filter frame onto
the air filter and install the
assembly in the case.
7. Install the air filter case cover
and panel.
EC000082
cC
8Make sure the air filter is prop-
erly seated in the air filter
case.
8The engine should never be
run without the air filter
installed. Excessive piston
and/or cylinder wear may
result.
Air filter case drain hose cleaning
Frequently check the hose at the
bottom of the air filter case. If dirt
or water is visible, remove and
clean the hose, then reinstall it.
1. Hose
Recommended oil:
Engine oil
1
21
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 43
Page 55 of 86

6-23
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9 8Use only the designated quali-
ty brake fluid. Otherwise, the
rubber seals may deteriorate,
causing leakage and poor
brake performance.
NOTE:
If DOT 4 is not available, DOT 3 can
be used.
8Refill with the same type of
brake fluid. Mixing fluids may
result in a harmful chemical
reaction and lead to poor
brake performance.
8Be careful that water does not
enter the master cylinder when
refilling. Water will significant-
ly lower the boiling point of
the fluid and may result in
vapor lock.8Brake fluid may deteriorate
painted surfaces or plastic
parts. Always clean up spilled
fluid immediately.
8Have a Yamaha dealer check
the cause if the brake fluid
level goes down.
EAU00742Brake fluid replacement
The brake fluid should be replaced
only by trained Yamaha service
personnel. Have the Yamaha deal-
er replace the following compo-
nents during periodic maintenance
or when they are damaged or leak-
ing:
8oil seals (every two years)
8brake hoses (every four years) Recommended brake fluid:
DOT 4
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 53
Page 58 of 86
6-26
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU02962Cable inspection and
lubrication
EW000112
w
Damage to the outer housing of
cables may lead to internal rusting
and interfere with the cable move-
ment. Replace damaged cables as
soon as possible to prevent unsafe
conditions.
Lubricate the cables and cable
ends. If a cable does not operate
smoothly, ask a Yamaha dealer to
replace it.EAU00773Throttle cable and grip
lubrication
The throttle twist grip assembly
should be greased at the time that
the cable is lubricated, since the
grip must be removed to get at the
end of the throttle cable. After
removing the screws, hold the end
of the cable up in the air and put in
several drops of lubricant. With the
throttle grip disassembled, coat the
metal surface of the grip assembly
with a suitable all-purpose grease. Recommended lubricant:
Engine oil
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 56
Page 59 of 86
6-27
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU02984Brake and shift pedal
lubrication
Lubricate the pivoting parts.
EAU02985Brake and clutch lever
lubrication
Lubricate the pivoting parts.
EAU02986Sidestand lubrication
Lubricate the sidestand pivoting
point and metal-to-metal contact
surfaces. Check that the sidestand
moves up and down smoothly.
EW000113
w
If the sidestand does not move
smoothly, consult a Yamaha deal-
er.
Recommended lubricant:
Engine oilRecommended lubricant:
Engine oil
Recommended lubricant:
Engine oil
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 57
Page 60 of 86
6-28
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU00791Rear suspension lubrication
Lubricate the pivoting parts.
1. Grease nipple (´2)
EAU02939Front fork inspection
Visual checkEW000115
w
Securely support the motorcycle
so there is no danger of it falling
over.
Check for scratches or damage on
the inner tube and excessive oil
leakage from the front fork.Operation check
1. Place the motorcycle on a level
place.
2. Hold the motorcycle in an
upright position and apply the
front brake.
3. Push down hard on the han-
dlebars several times and
check if the fork rebounds
smoothly.
EC000098
cC
If any damage or unsmooth move-
ment is found with the front fork,
consult a Yamaha dealer.
1
Recommended lubricant:
Lithium soap base grease
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 58
Page 77 of 86

8-1
EAU01038
SPECIFICATIONS
1
2
3
4
5
6
7
8
9
Specifications
Model TW125
Dimensions
Overall length 2,140 mm
Overall width 810 mm
Overall height 1,120 mm
Seat height 805 mm
Wheelbase 1,330 mm
Ground clearance 260 mm
Minimum turning radius 2,100 mm
Basic weight (with oil and full
fuel tank)125 kg
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined
single cylinder
Displacement 124 cm
3
Bore ´Stroke 57.0 ´48.8 mm
Compression ratio 10:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Type
Recommended engine oil
classification API Service SE, SF, SG type
or higher
cC
Be sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled “Energy
Conserving”) contain anti-friction additives which will cause
clutch and/or starter clutch slippage, resulting in reduced
component life and poor engine performance.
Capacity
Periodic oil change 1.0 L
With oil filter replacement 1.1 L
Total amount 1.3 L
Air filterWet type element
–10° 0° 10° 20° 30°
40°
SAE 10W/30
SAE 10W/40
SAE 20W/40
SAE 20W/50
–20°
SAE 15W/40 50°C
5EK-9-E1 (TW125)<3.1> 4/6/0 11:50 PM Page 75