2000 YAMAHA TTR125 wheel

4 - 76
ENGTRANSMISSION, SHIFT CAM AND SHIFT FORK
Transmission
1. Install:
l4th pinion gear (22T) 1
l3rd pinion gear (19T) 2
l2nd pinion gear (18T) 3
l5th pinion gear (24T) 4
On main axle 5.
NOTE:
lApply the molybdenum disulfide oil on the
gears’ inner circumference.
lInstall the 5th pinion gear so that measure-
ment a is 83.25 ~ 83.45 mm (3.278 ~
3.285 in).
2. Install:
l2nd wheel gear (32T) 1
l5th wheel gear (21T) 2
l3rd wheel gear (25T) 3
l4th wheel gear (23T) 4
l1st wheel gear (37T) 5
On drive axle 6.
NOTE:
Apply the molybdenum disulfide oil on the
gears’ inner circumference.

4 - 78
ENGTRANSMISSION, SHIFT CAM AND SHIFT FORK
Shift cam and shift fork
1. Install:
lShift fork 1 (L) 1
lShift fork 2 (C) 2
lShift fork 3 (R) 3
NOTE:
lMesh the shift fork #1 (L) with the 2nd wheel
gear and #3 (R) with the 4th wheel gear on
the drive axle.
lMesh the shift fork #2 (C) with the 3rd pinion
gear on the main axle.
2. Install:
lShift cam 1
NOTE:
Apply the engine oil on the shift cam.
3. Install:
lShift fork guide bar 1 (short) 1
lShift fork guide bar 2 (long) 2
NOTE:
lApply the engine oil on the guide bars.
lBe sure the long bar is inserted into the shift
forks #1 and #3 and the short one into #2.
4. Check:
lShifter operation
lTransmission operation
Unsmooth operation ® Repair.

5 - 1
CHAS

EC500000
CHASSIS
FRONT WHEEL AND FRONT BRAKE
Extent of removal:
1
Front wheel removal
2
Wheel bearing removal
3
Brake shoe plate assembly removal and disassembly
Extent of removal Order Part name Q’ty Remarks
Preparation for removal
FRONT WHEEL AND DRUM
BRAKE
Hold the machine by placing the
suitable stand under the engine.
1 Brake cable holder 1
2 Brake cable 1 Disconnect at the lever side, first.
3 Axle nut 1
4 Wheel axle 1
5 Front wheel 1
6 Collar set 1
7 Brake shoe plate assembly 1
8 Oil seal 1
9 Wheel bearing 2 Refer to “REMOVAL POINTS”.
10Spacer
1
WARNING
Support the machine securely so there is nodanger of it falling over.
2
3
1

FRONT WHEEL AND FRONT BRAKE
5

5 - 2
CHAS

Extent of removal Order Part name Q’ty Remarks
11 Brake shoe 2
12 Spring 2
13 Brake camshaft lever 1
14 Wear indicator plate 1
15 Brake camshaft 1
16 Brake shoe plate 1
3

FRONT WHEEL AND FRONT BRAKE

5 - 3
CHAS

FRONT WHEEL AND FRONT BRAKE
REMOVAL POINTS
EC513201
Wheel bearing (if necessary)
1. Remove:
l
Bearing
1

NOTE:

Remove the bearing using a general bearing
puller
2
.
INSPECTION
EC514100
Wheel
1. Measure:
l
Wheel runout
Out of limit
®
Repair/replace.
2. Inspect:
l
Bearing
Rotate inner race with a finger.
Rough spot/seizure
®
Replace.
NOTE:

Replace the bearings, oil seal and wheel collar
as a set.
Wheel runout limit:
Radial
1
: 2.0 mm (0.08 in)
Lateral
2
: 2.0 mm (0.08 in)
EC514200
Wheel axle
1. Measure:
l
Wheel axle bends
Out of specification
®
Replace.
Use the dial gauge
1
.
NOTE:

The bending value is shown by one half of the
dial gauge reading.
WARNING

Do not attempt to straighten a bent axle.
Wheel axle bending limit:
0.5 mm (0.020 in)

5 - 4
CHAS

FRONT WHEEL AND FRONT BRAKE
Drum brake
1. Inspect:
l
Brake shoe lining surface
Glazed areas
®
Polish.
Use coarse sand paper.
NOTE:

After polishing, wipe the polished particles with
a cloth.
2. Measure:
l
Brake shoe lining thickness
a

Out of specification
®
Replace.
NOTE:

Replace the brake shoes and springs as a set
if either is worn to the limit.
Brake shoe lining thickness:
Standard
40 mm
(0.16 in)2.0 mm
(0.08 in)
3. Measure:
l
Brake drum inside diameter
a

Out of specification
®
Replace.
Brake drum inside diameter:
Standard
110 mm
(4.33 in)111 mm
(4.37 in)
4. Inspect:
l
Brake drum inner surface
Oil/scratches
®
Remove.
OilUse a rag soaked in lac-
quer thinner or a solvent.
ScratchesUse a emery cloth (lightly
and evenly polishing).

5 - 5
CHAS

FRONT WHEEL AND FRONT BRAKE
ASSEMBLY AND INSTALLATION
Brake shoe plate assembly
1. Install:
l
Brake camshaft
1

NOTE:

Apply the lithium soap base grease on the
brake camshaft.
2. Check:
l
Brake camshaft operation
Unsmooth operation
®
Repair.
3. Install:
l
Wear indicator plate
1

NOTE:

When installing the wear indicator plate to the
brake camshaft align the projection
a
on the
wear indicator plate with the slots
b
on the
brake camshaft.
4. Install:
l
Brake camshaft lever
1

NOTE:

Install the brake camshaft lever so that the
angle
b
between a line drawn, through the
hub of the brake shoe and dot
a
, and a line
drawn through the midline of the camshaft and
dot
a
is 84˚.
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)

5. Install:
l
Springs
1

lBrake shoes 2
NOTE:
Apply the lithium soap base grease on the
pivot pin.
WARNING
Do not apply grease to the brake shoe lin-
ings.
New

5 - 6
CHASFRONT WHEEL AND FRONT BRAKE
Front wheel
1. Install:
lWheel bearing 1
lSpacer 2
lWheel bearing 3
lOil seal 4
NOTE:
lApply the lithium soap base grease on the
wheel bearing and oil seal lip when installing.
lInstall the wheel bearing so that the enclosed
side is facing outward.
lUse a socket that matches the outside diam-
eter of the race of the bearing.
lLeft side of wheel bearing shall be installed first.
lInstall the oil seal with its manufacture's
marks or numbers facing outward.
CAUTION:
Do not strike the inner race of the bearing.
Contact should be made only with the outer
race.
2. Install:
lBrake shoe plate assembly
lCollar set 1
NOTE:
Apply the lithium soap base grease on the oil
seal lip.
New
3. Install:
lFront wheel
NOTE:
Make sure that the slot a on the brake shoe
plate with the stopper b on the front fork outer
tube.
4. Install:
lWheel axle 1
NOTE:
Apply the lithium soap base grease on the
wheel axle.