2000 YAMAHA CYGNUS 125 drain bolt

6-9
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
screwing it in), and then remove it
again to check the oil level.
NOTE:
The engine oil should be between the
minimum and maximum level marks.ZAUM00**
1
2
1. Maximum level mark
1. Minimum level mark4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for sev-
eral minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap and
drain bolts to drain the oil from the
crankcase.
ECA10410
cCWhen removing the engine oil drain
bolt, the O-ring, spring, and oil
strainer will fall out. Take care not to
lose these parts.ZAUM00**
1
1. Oil filler cap
ZAUM00**
1
1. Engine oil drain bolt AZAUM00**
1
1. Engine oil drain bolt B4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, spring, O-ring
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 9

6-10
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
and engine oil drain bolts, and then
tighten the drain bolts to the speci-
fied torque.
Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m  kgf, 14.5ft  lbf)
Engine oil drain bolt B:
20 Nm (2.0 m  kgf, 14.5 ft  lbf)
NOTE:
Make sure that the O-ring is properly
seated.7. Add the specified amount of the
recommended engine oil, and then
install and tighten the engine oil filler
cap.
Recommended engine oil:
See page 8-1.
Oil change quantity:
0.9 L (0.98 US qt) (0.83 Imp.qt)
ECA11670
cC8 88 8
8Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. Inaddition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
8 88 8
8Be sure no foreign material en-
ters the crankcase.
8. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
9. Turn the engine off, and then check
the oil level and correct it if neces-
sary.
10. Reset the oil change indicator. (See
page 3-2 for reset procedures.)NOTE:
If the engine oil is changed before the
oil change indicator changes to red (i.e.
before the periodic oil change interval
has been reached), the indicator must
be reset after the oil change for the next
periodic oil change to be indicated at the
correct time.
EAU20060
Final transmission oilThe final transmission case must be
checked for oil leakage before each ride.
If any leakage is found, have a Yamaha
dealer check and repair the scooter. In
addition, the final transmission oil must
be changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several min-
utes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 10

6-11
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
ZAUM00**
1
1. Final transmission oil filler cap5. Install the final transmission oil
drain bolt, and then tighten it to the
specified torque.ZAUM00**
1
1. Final transmission oil drain bolt
Tightening torque:
Final transmission oil drain bolt:
23 Nm (2.3 m  kgf, 16.6 ft  lbf)
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten the
oil filler cap.
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.13 L (0.14 US qt) (0.1 Imp.qt)
EWA11310
w8 88 8
8Make sure that no foreign mate-
rial enters the final transmission
case.
8 88 8
8Make sure that no oil gets on the
tire or wheel.7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAUT1341
Air filter and V-belt case air fil-
ter elementsThe air filter and V-belt case air filter el-
ements should be cleaned at the inter-
vals specified in the periodic mainte-
nance and lubrication chart. Clean both
filter elements more frequently if you are
riding in unusually wet or dusty areas.
Cleaning the air filter element
1. Place the scooter on the
centerstand.
2. Remove the air filter case cover by
removing the screws.ZAUM00**
2(×6)
1
1. Air filter case cover
2. Screw3. Pull the air filter element out, and
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 11

7-3
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGE
8 88 8
8Avoid using abrasive polishing
compounds as they will wear
away the paint.NOTE:
Consult a Yamaha dealer for advice on
what products to use.
EAU26300
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover.
ECA10820
cC8 88 8
8Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
8 88 8
8To prevent corrosion, avoid
damp cellars, stables (because of
the presence of ammonia) and
areas where strong chemicals are
stored.Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
up. Pour the drained fuel into the
fuel tank.3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent the
fuel tank from rusting and the fuel
from deteriorating.
4. Perform the following steps to pro-
tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
5ML-F8199-E0ch7re.pmd2003/12/12, 16:04 3