2000 TOYOTA TACOMA towing

’00 Tacoma(U)
31
To release the belt, press the buckle−re-
lease button.The buckles can be fixed when not in
use.
When taking out the buckle from the hold-
er, pull on the belt webbing to remove the
buckle from the lower portion.
Seat belt extender
If your seat belt cannot be fastened se-
curely because it is not long enough, a
personalized seat belt extender is avail-
able from your Toyota dealer free of
charge.
Please contact your local Toyota dealer so
that the dealer can order the proper re-
quired length for the extender. Bring the
heaviest coat you expect to wear for prop-
er measurement and selection of length.
Additional ordering information is available
at your Toyota dealer.
CAUTION
When using the seat belt extender,
observe the following. Failure to fol-
low these instructions could result in
less effectiveness of the seat belt re-
straint system in case of vehicle acci-
dent, increasing the chance of per-
sonal injury.
Never use the seat belt extender if
you can fasten the seat belt without
it.
Stowing the rear seat
buckles

’00 Tacoma(U)
77
The gauge indicates the engine coolant
temperature when the ignition switch is
on. The engine operating temperature
will vary with changes in weather and
engine load.
If the needle moves into the red zone,
your engine is too hot. If your vehicle
overheats, stop your vehicle and allow the
engine to cool.
Your vehicle may overheat during severe
operating conditions, such as:
Driving up a long hill on a hot day.
Reducing speed or stopping after high
speed driving.
Idling for a long period with the air
conditioning on in stop−and−go traffic.
Towing a trailer.
NOTICE
Do not remove the thermostat in
the engine cooling system as this
may cause the engine to overheat.
The thermostat is designed to con-
trol the flow of coolant to keep the
temperature of the engine within
the specified operating range.
 Do not continue driving with an
overheated engine. See If your ve-
hicle overheats" in Section 4.
Tachometer
The tachometer indicates engine speed
in thousands of rpm (revolutions per
minute). Use it while driving to select
correct shift points and to prevent en-
gine lugging and overrevving.
Driving with the engine running too fast
causes excessive engine wear and poor
fuel economy. Remember, in most cases
the slower the engine speed, the greater
the fuel economy.
NOTICE
Do not let the indicator needle get
into the red zone. This may cause
severe engine damage.

’00 Tacoma(U)
87
(c) Using 2" and L" positions
The 2" and L" positions are used for
strong engine braking as described pre-
viously.
With the selector lever in 2" or L", you
can start the vehicle in motion as with the
lever in D".
With the selector lever in 2", the vehicle
will start in the first gear and automatical-
ly shift to second gear.
With the selector lever in L", the trans-
mission is engaged in first gear.NOTICE
Be careful not to overrev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:
2" 124 km/h(77 mph) . . . . . . . . . . . .
L" 72 km/h(45 mph)
. . . . . . . . . . . .
 Do not continue hill climbing for a
long time in the 2" or L" posi-
tion. This may cause severe auto-
matic transmission damage from
overheating. To prevent such dam-
age, use D" position for hill climb-
ing or hard towing.
(d) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
R" position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(e) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever fully to securely apply the parking brake.
3. With the brake pedal pressed down, shift the selector lever to the P" posi-
tion.
CAUTION
While the vehicle is moving, never
attempt to move the selector lever
into P" position under any circum-
stances. Serious mechanical damage
and loss of vehicle control may re-
sult.
(f) Good driving practice
If the transmission is repeatedly up-
shifted and downshifted between third
gear and overdrive when climbing a
gentle slope, the overdrive switch
should be turned off. Be sure to turn
the switch on immediately afterward.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.

’00 Tacoma(U)
90
(b) Overdrive switch
You can select either a third gear (with
overdrive off) or fourth gear (with over-
drive on) by pushing this switch.
To turn the overdrive off, push the switch.
The O/D OFF" indicator light should come
on. To turn the overdrive on again, push
the switch again. The O/D OFF" indicator
light should go off.
Always drive your vehicle with the over-
drive on for better fuel economy and
quieter driving.
If the engine is turned off when the over-
drive is off and restarted, the overdrive
will automatically be on.Vehicles with cruise controlWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking will not be applied because the
cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise control" in this section.
(c) Normal driving
1. Start the engine as instructed in How to start the engine" in Section 3. The
transmission must be in P" or N".
2. With your foot holding down the brake pedal, shift the selector lever to D".
When the lever is in the D" position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc.
Always turn the overdrive switch on for
better fuel economy and quieter driving. If
the engine coolant temperature is low, the
transmission will not shift into the over-
drive gear even with the overdrive on.
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake pedal. Depress the accelerator pedal
slowly for smooth starting.
(d) Using engine braking
To use engine braking, you can downshift
the transmission as follows:
Push the overdrive switch. The O/D
OFF" indicator light will come on and
the transmission will downshift to the
third gear.
Shift into the 2" position. The trans-
mission will downshift to the second
gear when the vehicle speed drops
down to or lower than 131 km/h (81
mph), and stronger engine braking will
be enabled.
Shift into the L" position. The trans-
mission will downshift to the first gear
when the vehicle speed drops down to
or lower than 63 km/h (39 mph), and
maximum engine braking will be ap-
plied.

’00 Tacoma(U)
91
Vehicles with cruise controlWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking is not applied because the cruise
control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise control" in this section.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
(e) Using 2" and L" positions
The 2" and L" positions are used for
strong engine braking as described pre-
viously.
With the selector lever in 2" or L", you
can start the vehicle in motion as with the
lever in D".
With the selector lever in 2", the vehicle
will start in the first gear and automatical-
ly shift to the second gear.
With the selector lever in L", the trans-
mission is engaged in first gear.
NOTICE
Be careful not to overrev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:
2" 136 km/h (85 mph) . . . . . . . . . . . .
L" 74 km/h (46 mph)
. . . . . . . . . . . .
 Do not continue hill climbing for a
long time in the 2" or L" posi-
tion. This may cause severe auto-
matic transmission damage from
overheating. To prevent such dam-
age, use D" position for hill climb-
ing or hard towing.
(f) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
R" position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(g) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever fully to securely apply the parking brake.
3. With the brake pedal pressed down, shift the selector lever to the P" posi-
tion.
CAUTION
Never attempt to move the selector
lever into P" position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.
(h) Good driving practice
If the transmission is repeatedly shifts
up and down between third gear and
overdrive when climbing a gentle slope,
the overdrive should be turned off. Be
sure to turn the switch on immediately
afterward.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.

’00 Tacoma(U)
95
(b) Overdrive switch
You can select either a third gear (with
overdrive off) or fourth gear (with over-
drive on) by pushing this switch.
To turn the overdrive off, push the switch.
The O/D OFF" indicator light should come
on. To turn the overdrive on again, push
the switch again. The O/D OFF" indicator
light should go off.
Always drive your vehicle with the over-
drive on for better fuel economy and
quieter driving.
If the engine is turned off when the over-
drive is off and restarted, the overdrive
will be on automatically.Vehicles with cruise controlWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking will not be applied because the
cruise control is not cancelled.
For ways to decrease the vehicle speed,
see Cruise control" in this section.
(c) Normal driving
1. Start the engine as instructed in How to start the engine" in Section 3. The
transmission must be in P" or N".
When the front drive control lever is in
L4" (low−speed position, four−wheel
drive), the driving pattern selector setting
has no effect on gear shift timing. (See
Four−wheel drive system" in this section
for information of the front drive control
lever.)
2. With your foot holding down the brake pedal, shift the selector lever to D".
When the lever is in the D" position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc. Always turn the overdrive switch on for
better fuel economy and quieter driving. If
the engine coolant temperature is low or
when the front drive control lever is in
L4" (low−speed position, four−wheel
drive), the transmission will not shift into
the overdrive gear even with the overdrive
on. (See Four−wheel drive system" in this
section for information of the front drive
control lever.)
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake
pedal. Depress the accelerator pedal
slowly for smooth starting.
(d) Using engine braking
To use engine braking, you can downshift
the transmission as follows:
Push the overdrive switch. The O/D
OFF" indicator light will come on and
the transmission will downshift to the
third gear.

’00 Tacoma(U)
97
Front drive control lever in L4"3RZ−FE engine2" 43 km/h (27 mph) . . . . . . . . .
L" 22 km/h (14 mph) . . . . . . . . .
5VZ−FE engine 2" 46 km/h (29 mph) . . . . . . . . .
L" 25 km/h (16 mph) . . . . . . . . .
Pre Runner
3RZ−FE engine2" 114km/h (71 mph) . . . . . . . .
L" 63 km/h (39 mph) . . . . . . . .
5VZ−FE engine 2" 120km/h (75 mph) . . . . . . . .
L" 66 km/h (41 mph) . . . . . . . .
 Do not continue hill climbing for a
long time in the 2" or L" posi-
tion. This may cause severe auto-
matic transmission damage from
overheating. To prevent such dam-
age, use D" position for hill climb-
ing or hard towing.(f) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
R" position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(g) Parking
1. Bring the vehicle to a complete stop.
2. Pull the parking brake lever fully to securely apply the parking brake.
3. With the brake pedal pressed down, shift the selector lever to the P" posi-
tion.
CAUTION
Never attempt to move the selector
lever into P" position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.
(h) Good driving practice
If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope, the
overdrive should be turned off. Be sure
to turn the switch on immediately after-
ward.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.
CAUTION
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.
NOTICE
Do not hold the vehicle on an up-
grade with the accelerator pedal. It
can cause the transmission to over-
heat. Always use the brake pedal or
parking brake.

’00 Tacoma(U)
100
Upshifting too soon or downshifting too
late will cause lugging, and possibly ping-
ing. Regularly revving the engine to maxi-
mum speed in each gear will cause ex-
cessive engine wear and high fuel
consumption.
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
Two−wheel drive models2RZ−FE engine gear km/h(mph)1 \b\b48\b(30)
2 \b\b88\b\b(55)
3 \b136\b\b(85)
4 \b165(103)
5VZ−FE engine gear km/h(mph)
1 \b\b54\b\b(34)
2 \b101\b\b(63)
3 \b144\b\b(89)
4 \b165\b(103) Four−wheel drive models
3RZ−FE engine
gear km/h(mph)
H2" and H4" L4"
1 \b46\b\b(29) 17(11)
2 \b86\b\b(53) 33(21)
3 135\b\b(84) 52(32)
4 165\b(103) 66(41)
5VZ−FE engine gear km/h(mph) H2" and H4" L4"
1 \b48\b\b(30) 18(11)
2 \b88\b\b(55) 34(21)
3 128\b\b(80) 49(30)
4 165\b(103) 72(45)
NOTICE
Do not downshift if you are going
faster than the maximum allowable
speed for the next lower gear.
Good driving practice
If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.
When towing a trailer, in order to main-
tain engine braking efficiency, do not
use the fifth gear.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
NOTICE
Make sure the vehicle is completely
stopped before shifting into reverse.