SOLARA_U
140
Glove box
To use the glove box, do this.
To open: Pull the lever.
With the instrument panel lights on, the
glove box light will come on when the
glove box is open.
To lock: Insert the master key and turn it
clockwise.
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the glove box door
closed while driving.
Garage door opener
The garage door opener is manufac-
tured under license from HomeLink
and can be programmed to operate ga-
rage doors, estate gates, security light-
ing, etc.
(a) Programming HomeLink
The HomeLink has 3 buttons and can
be programmed to operate 3 separate
devices.
NOTICE
Unplug the garage or gate device dur-
ing programming to prevent possible
motor burn−up.
Prepare the HomeLink for programming
by erasing all codes or the memorized
date programmed by the former owner.
Follow the procedure in (c) Erasing the
garage door opener memory".
1. Decide which one of the 3 buttons you want to program. Push and hold down
the button for about 20 seconds until
the indicator light begins to flash.
While holding this button down, follow
steps 2 and 3.
2. Bring the hand held garage door open- er to within about 25 mm (1 in.) of the
button being programmed and push the
button on the hand held garage door
opener. The signal from the hand held
garage door opener is sent to the ve-
hicle’s opener.
3. When the frequency and code is regis- tered, the indicator light flashers rapid-
ly. At this point, your can release both
buttons.
4. To program the remaining buttons, re- peat steps 1 through 3.
SOLARA_U
141
NOTICE
Canada only:
As your hand held garage door open-
er may automatically stop sending the
signal during programming, press and
re−press the hand held garage door
opener button every two seconds dur-
ing steps 1 through 4 above until the
frequency and code is registered.
If you want to replace an existing program
with a new program, select the button
you want to program. Follow the proce-
dure from step 1.
If the transmitter has a rolling code
feature, it is necessary to program the
in−garage receiver after programming
HomeLink.
1. Locate the training or learning but- ton on the in−garage receiver and
push and release this button. Loca-
tion of the button may vary among
garage door opener manufacturers. 2. Firmly push and release the trained
HomeLink button 2 times (some ga-
rage door manufacturers may require
you to push the HomeLink button
up to 3 times) to complete the pro-
cess.
The garage door should now operate
when the HomeLink button is pushed.
Do not use the HomeLink universal
transmitter with any garage door opener
that lacks the safety stop and reverse
feature as required by Federal Safety
Standards. This includes any garage door
opener model manufactured before April 1,
1982.
CAUTION
When programming or operating the
garage door opener, make sure there
is no one around the moving door.
(b) Operating the garage door opener
Push the appropriate button to activate the
garage door opener. The indicator light
comes on. The garage door opener contin-
ues to send the signal as long as the
button is pushed (up to 20 seconds). (c) Erasing the garage door opener
memory
Push and hold down the 2 outside buttons
for about 20 seconds until the indicator
light flashes. All memorized data will be
erased.
FCC ID: CB2V94800
CANADA: 1763 102 264
This device complies with FCC Part 15.
Operation is subject to the following two
conditions: (1) This device may not
cause harmful interference, and (2) this
device must accept any interference that
may be received, including interference
that may cause undesired operation.
WARNING: This transmitter has been
tested and complies with FCC and
DOC/MDC rules. Changes or modifica-
tions not expressly approved by the
partly responsible for compliance
could void the user’s authority to op-
erate the device.
