2000 TOYOTA CAMRY width

LU03P±03
Z19249
A
BB AA A AA A
A A
A
S05928
LU0420
Seal Width
3 ± 5 mm
A
A
BBC
C
5 mm (0.20 in.)
± LUBRICATION (5S±FE)OIL PUMP
LU±13
1659 Author: Date:
INSTALLATION
1. INSTALL OIL PUMP
Install a new gasket and the oil pump with the 12 bolts. Uniformi-
ty tighten the bolts in several passes.
Torque: 8.8 N´m (90 kgf´cm, 78 in.´lbf)
HINT:
Each bolt length is indicated in the illustration.
Bolt length:
25 mm (0.98 in.) for A
35 mm (1.38 in.) for B
2. INSTALL OIL PUMP PULLEY (See page EM±23)
3. INSTALL CRANKSHAFT TIMING PULLEY
(See page EM±23)
4. INSTALL NO.2 IDLER PULLEY (See page EM±23)
5. INSTALL TIMING BELT (See page EM±23)
6. INSTALL OIL STRAINER
Install a new gasket and the oil strainer with the bolt and 2 nuts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
7. INSTALL OIL PAN
(a) Remove any old seal packing (FIPG) material and be
careful not to drop any oil on the contact surfaces of the
oil pan and cylinder block.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing groove.

Thoroughly clean all components to remove all the
loose material.

Using a non±residue solvent, clean both sealing
surface.
NOTICE:
Do not use a solvent which will affect the painted surfaces.
(b) Apply seal packing to the oil pan shown in the illustration.
Seal packing: Part No. 08826±00080 or equivalent

Install a nozzle that has been cut to a 3 ± 5 mm (0.12
± 0.20 in.) opening.

Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

LU02D±03
P12969
A
Seal Width
2 ± 3 mmB
A
BC
C
P18779
New O±Ring
± LUBRICATION (1MZ±FE)OIL PUMP
LU±15
1679 Author: Date:
INSTALLATION
1. INSTALL OIL PUMP
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surfaces of the oil pump
and cylinder block.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.

Thoroughly clean all components to remove all the
loose material.

Using a non±residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the oil pump as shown in the illustra-
tion.
Seal packing: Part No. 08826±00080 or equivalent

Install a nozzle that has been cut to a 2 ± 3 mm (0.08
± 0.12 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Place a new O±ring on the cylinder block.

B04402
A Region ºXºRegion ºYº
A
CB B
C
Seal Width
Type A: 4 ± 5 mm
Type B: 3 ± 4 mmRegion ºXºRegion ºYº
AC Type A
Type B
± LUBRICATION (1MZ±FE)OIL PUMP
LU±17
1681 Author: Date:
(b) Apply seal packing to the oil pan as shown in the illustra-
tion.
Seal packing: Part No. 08826±00080 or equivalent
Region ºXº is at the outer side of the bolt hole.
Region ºYº is at the inner side of the bolt hole.

Install a nozzle that has been cut to a 4 ± 5 mm (0.16
± 0.20 in.) (Type A) or 3 ± 4 mm (0.12 ± 0.16 in.)
(Type B) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the oil pan with the 19 bolts (or 17 bolts and 2 nuts).
Uniformly tighten the bolts and nuts in several passes.
Torque:
10 mm head: 8 N´m (80 kgf´cm, 69 in.´lbf)
12 mm head: 19.5 N´m (200 kgf´cm, 14 ft´lbf)
14 mm head: 37.2 N´m (380 kgf´cm, 27 ft´lbf)
(d) Install the flywheel housing under cover and exhaust pipe
support stay with the 2 bolts.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
5. INSTALL OIL STRAINER
Install a new gasket and the oil strainer with the bolt and 2 nuts.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
6. INSTALL NO.2 OIL PAN
(a) Remove any old packing (FIPG) material and be careful
not to drop any oil on the contact surface of the No.1 and
No.2 oil pans.

Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.

Thoroughly clean all components to remove all the
loose material.

Using a non±residue solvent, clean both sealing
surfaces.
NOTICE:
Do not use a solvent which will affect the painted surfaces.

P12568
A
A
BB
Seal Width
4 ± 5 mm LU±18
± LUBRICATION (1MZ±FE)OIL PUMP
1682 Author: Date:
(b) Apply seal packing to the No.2 oil pan as shown in the il-
lustration.
Seal packing:
Part No. 08826±00080 or equivalent

Install a nozzle that has been cut to a 4 ± 5 mm (0.16
± 0.20 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the No.2 oil pan with the 10 bolts and 2 nuts. Uni-
formly tighten the bolts and nuts in several passes.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
7. INSTALL A/C COMPRESSOR HOUSING BRACKET
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
8. INSTALL NO.3 TIMING BELT COVER
(See page EM±21)
9. INSTALL TIMING PULLEYS (See page EM±21)
10. INSTALL TIMING BELT (See page EM±21)
11. INSTALL ADJUSTING STRUT AND PS PUMP DRIVE
BELT
(a) Temporarily install the adjusting strut with the bolt and the
nut.
(b) Install the drive belt with the pivot and adjusting bolts.
Torque: 43.1 N´m (440 kgf´cm, 32 ft´lbf)
(c) Tighten the nut.
Torque: 43.1 N´m (440 kgf´cm, 32 ft´lbf)
12. INSTALL A/C COMPRESSOR (See page AC±47)
13. INSTALL GENERATOR DRIVE BELT
(See page CH±16)
14. INSTALL FRONT EXHAUST PIPE BRACKET TO
NO.1 OIL PAN
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
15. INSTALL FRONT EXHAUST PIPE (See page EM±76)
16. REMOVE RH FENDER APRON SEAL
17. REMOVE RH FRONT WHEEL
18. FILL ENGINE WITH OIL
19. START ENGINE AND CHECK FOR LEAKS
20. RECHECK ENGINE OIL LEVEL

PP0MS±01
PP±100
± PREPARATIONSUPPLEMENTAL RESTRAINT SYSTEM
152 Author: Date:
EQUIPMENT
Torque wrench
Bolt: Length: 35 mm (1.38 in.) Pitch: 1.0 mm (0.039 in.)
Diam.: 6.0 mm (0.236 in.)Airbag disposal
Tire Width: 185 mm (7.28 in.) Inner diam.: 360mm (14.17 in.)Airbag disposal
Tire with disc wheel Width: 185 mm (7.28 in.)
Inner diam.: 360 mm (14.17 in.)Airbag disposal
Vinyl bagAirbag disposal

PP0MV±01
± PREPARATIONBODY
PP±105
157 Author: Date:
EQUIPMENT
Clip remover
Torque wrench
Drill
Drill bit, diam 3.2 mm (0.126 in.)
Hand riveter
TapeTo avoid surface damage
Adhesive tapeTo avoid surface damage
Adhesive
Cleaner
Shop ragRegulator handle
Water pump pliersWindow regulator
KnifeMoulding
Heat lightMoulding
Piano wireWindshield
Rope (no projections, difficult to break)Seat belt pretensioner disposal
Tire Width: 185 mm (7.28 in.)
Inner diam: 360 mm (14.17 in.)Seatbelt pretensioner disposal
Tire with disc wheel Width: 185 mm (7.28 in.)
Inner diam 360 mm (14.17 in.)Seat belt pretinsioner disposal
Vinyl bagSeat belt pretensioner disposal

SS0AD±03
SS±6
± SERVICE SPECIFICATIONSENGINE MECHANICAL (5S±FE)
169 Author: Date:
ENGINE MECHANICAL (5S±FE)
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,226 kPa (12.5 kgf/cm2, 178 psi) or more
981 kPa (10.0 kgf/cm2, 142 psi)
98 kPa (1.0 kgf/cm2, 14 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim (for repair part) Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.19 ± 0.29 mm (0.007 ± 0.011 in.)
0.28 ± 0.38 mm (0.011 ± 0.015 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC18 ± 12° BTDC @ idle
Idle speed±700 ± 50 rpm
Idler pulley
tension springFree length
Installed load at 50.5 mm (1.988 in.)42.0 mm (1.654 in.)
32 ± 37 N (3.25 ± 3.75 kgf, 7.2 ± 8.3 lbf)
Cylinder headWarpage
Cylinder block side Maximum
Manifold sideMaximum
Valve seat
Refacing angle
Contacting angle
Contacting width
0.05 mm (0.0020 in.)
0.08 mm (0.0031 in.)
30°, 45°, 75°
45°
1.0 ± 1.4 mm (0.039 ± 0.055 in.)
Valve guide
bushingInside diameter
Outside diameter (for repair part) STD
O/S 0.056.010 ± 6.030 mm (0.2366 ± 0.2374 in.)
11.048 ± 11.059 mm (0.4331 ± 0.4342 in.)
11.050 ± 11.077 mm (0.4350 ± 0.4361 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Vale face angle
Stem diameterIntake
Eh t
97.40 ± 97.80 mm (3.8346 ± 3.8504 in.)
98.25 ± 98.65 mm (3.8681 ± 3.8839 in.)
97.1 mm (3.823 in.)
98.0 mm (3.858 in.)
44.5°
5.970 ± 5.985 mm (0.2350 ± 0.2356 in.)
5 965 5 980 (0 2348 0 2354 i )Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Minimum5.965 ± 5.980 mm (0.2348 ± 0.2354 in.)
0.025 ± 0.060 mm (0.0010 ± 0.0024 in.)
0.030 ± 0.065 mm (0.0012 ± 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
0.8 ± 1.2 mm (0.031 ± 0.047 in.)
0.5 mm (0.020 in.)
Valve springDeviation Maximum
Free length
Installed tension at 34.7 mm (1.366 in.)2.0 mm (0.079 in.)
40.95 ± 42.80 mm (1.6122 ± 1.6850 in.)
164 ± 189 N (16.7 ± 19.3 kgf, 36.8 ± 42.5 lbf)

SS076±02
± SERVICE SPECIFICATIONSENGINE MECHANICAL (1MZ±FE)
SS±11
174 Author: Date:
ENGINE MECHANICAL (1MZ±FE)
SERVICE DATA
Compression
pressureat 250 rpm STD
Minimum
Difference of pressure between each cylinder1,500 kPa (15.3 kgf/cm2, 218 psi)
1,000 kPa (10.2 kgf/cm2, 145 psi)
100 kPa (1.0 kgf/cm2, 15 psi) or less
Valve
clearanceat cold Intake
Exhaust
Adjusting shim for repair part Mark 2.500
Mark 2.550
Mark 2.600
Mark 2.650
Mark 2.700
Mark 2.750
Mark 2.800
Mark 2.850
Mark 2.900
Mark 2.950
Mark 3.000
Mark 3.050
Mark 3.100
Mark 3.150
Mark 3.200
Mark 3.250
Mark 3.3000.15 ± 0.25 mm (0.006 ± 0.010 in.)
0.25 ± 0.35 mm (0.010 ± 0.014 in.)
2.500 mm (0.0984 in.)
2.550 mm (0.1004 in.)
2.600 mm (0.1024 in.)
2.650 mm (0.1043 in.)
2.700 mm (0.1063 in.)
2.750 mm (0.1083 in.)
2.800 mm (0.1102 in.)
2.850 mm (0.1122 in.)
2.900 mm (0.1142 in.)
2.950 mm (0.1161 in.)
3.000 mm (0.1181 in.)
3.050 mm (0.1201 in.)
3.100 mm (0.1220 in.)
3.150 mm (0.1240 in.)
3.200 mm (0.1260 in.)
3.250 mm (0.1280 in.)
3.300 mm (0.1299 in.)
Ignition timingw/ Terminals TE1 and E1 connected of DLC18 ± 12° BTDC @ idle
Idle speed±700 ± 50 rpm
Timing belt
tensionerProtrusion from housing side10.0 ± 10.8 mm (0.394 ± 0.425 in.)
Cylinder headWarpage Maximum
Valve seat
Refacing angle
Contacting angle
Contacting width
Valve guide bushing bore diameter STD
O/S 0.05
12 pointed head cylinder head bolt diameter
at tension portion STD
Minimum0.10 mm (0.039 in.)
30°, 45°, 75°
45°
1.0 ± 1.4 mm (0.039 ± 0.055 in.)
10.295 ± 10.313 mm (0.4053 ± 0.4080 in.)
10.345 ± 10.363 mm (0.4073 ± 0.4080 in.)
8.95 ± 9.05 mm (0.3524 ± 0.3563 in.)
8.75 mm (0.3445 in.)
Valve guide
bushingInside diameter
Outside diameter for repair part STD
O/S 0.055.510 ± 5.530 mm (0.2169 ± 0.2177 in.)
10.333 ± 10.344 mm (0.4068 ± 0.4072 in.)
10.383 ± 10.394 mm (0.4088 ± 0.4092 in.)
ValveValve overall length STD Intake
Exhaust
Minimum Intake
Exhaust
Valve face angle
Stem diameterIntake
Exhaust
Stem oil clearance STD Intake
Exhaust
Maximum Intake
Exhaust
Margin thickness STD
Maximum95.45 mm (3.5779 in.)
95.40 mm (3.7559 in.)
94.95 mm (3.7382 in.)
94.90 mm (3.7362 in.)
44.5°
5.470 ± 5.485 mm (0.2154 ± 0.2159 in.)
5.465 ± 5.480 mm (0.2152 ± 0.2157 in.)
0.025 ± 0.060 mm (0.0010 ± 0.0024 in.)
0.030 ± 0.065 mm (0.0012 ± 0.0026 in.)
0.08 mm (0.0031 in.)
0.10 mm (0.0039 in.)
1.0 mm (0.039 in.)
0.5 mm (0.020 in.)