Page 87 of 279
132000 4Runner (OM35762U)
Engine immobiliser system
The engine immobiliser system is a
theft prevention system. When you in-
sert the key in the ignition switch, the
transponder chip in the key's head
transmits an electronic code to the ve-
hicle. The engine will start, only when
the electronic code in the chip corre-
sponds to the registered ID code for
the vehicle.The system is automatically set when the
key is removed from the ignition switch.
The indicator light will start flashing every
2 seconds to show the system is set.
If either of the following indicator condi-
tions occurs, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is set-
ting or activating. (See Theft deterrent
systemº.)
The indicator light does not start flash-
ing when the key is removed from the
ignition switch.
The indicator light flashes unsteady.Inserting the registered key in the ignition
switch automatically cancels the system,
which enables the engine to start. The
indicator light will go off.
For your Toyota dealer to make you a
new key with built- in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
If you make your own duplicate key,
you will not be able to cancel the sys-
tem or start the engine.
NOTICE
Do not modify, remove or disas-
semble the engine immobiliser sys-
tem. If any unauthorized changes or
modifications are made, the proper
operation of the system cannot be
guaranteed.
ProCarManuals.com
Page 89 of 279
152000 4Runner (OM35762U)
LOCKING AND UNLOCKING WITH
INSIDE LOCK BUTTON
Move the lock button.
To lock: Push the button downward.
To unlock: Pull the button upward.
Closing the door with the lock button
pushed in will also lock the door. Be care-
ful not to lock your keys in the vehicle.
Vehicles with power door lock sys-
temÐThe front doors cannot be locked if
you leave the key in the ignition switch.
Driver's side
Front passenger's side
With power windows
Front passenger's side Driver's side
Without power windows
ProCarManuals.com
Page 92 of 279
182000 4Runner (OM35762U)
OPENING THE BACK WINDOW
To open the back window, push the
back window open switch of the trans-
mitter for about 1 second. The window
will fully open.
At this time, you can hear a beep.
If the ignition switch is in the ONº posi-
tion, the back window cannot be opened
by the back window open switch.
To open the back window with the master
key, see Power back windowº in this sec-
tion.
The volume of beep sound can be
changed. Contact your Toyota dealer for
details if you require it.PANICº SWITCH
Pushing the PANICº switch blows the
horn intermittently and flashes the
headlights and tail lights.
The PANICº switch is used to deter ve-
hicle theft when you witness anyone at-
tempting to break into or damage your
vehicle.
The alarm will last for one minute. To stop
alarm midway, push the PANICº or
UNLOCKº switch, or unlock any side door
or back door with key. You can also stop
the alarm by turning the ignition key from
LOCKº to the ONº position.The PANICº mode does not work when
the ignition key is in the ONº position.
WIRELESS REMOTE CONTROL
TRANSMITTER
The wireless remote control transmitter is
an electronic component. Observe the fol-
lowing instructions in order not to cause
damage to the transmitter.
Do not leave the transmitter on places
where the temperature becomes high
such as on the dashboard.
Do not disassemble it.
Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
You can use up to 4 wireless remote con-
trol transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.
ProCarManuals.com
Page 96 of 279
222000 4Runner (OM35762U)
The windows can be operated with the
switch on each side door.
The power windows work when the ignition
switch is in the ONº position.
Key off operation: If both front side
doors are closed, they work for 43 se-
conds even after the ignition switch is
turned off. They stop working when either
front side door is opened.
OPERATING THE DRIVER'S AND FRONT
PASSENGER'S WINDOWS
Use the switches on the driver's door
and front passenger 's door.
Normal operation: The window moves as
long as you hold the switch.
To open: Lightly push down the switch.
To close: Lightly pull up the switch.
If you push in the window lock switch on
the driver 's door, the front passengers'
window cannot be operated.
Driver's door switches
Front passenger's door switch
Automatic operation: Push the switch
completely down or pull it completely up,
and then release it. The window will fully
open or close. To stop the window part-
way, lightly move the switch in the oppo-
site direction and then release it.
If you push in the window lock switch on
the driver 's door, the front passengers'
window cannot be operated.
Jam protection function: During automat-
ic closing operation, the window stops and
opens half way if something gets caught
between the window and window frame.
If the window receives a strong impact,
this function may work even if nothing is
caught.
CAUTION
Never try jamming any part of your
body to make the jam protection
function work intentionally.
The jam protection function may
not work if something gets caught
just before the window is fully
closed.
ProCarManuals.com
Page 98 of 279
242000 4Runner (OM35762U)
Power back window
The back window can be operated with
the inner switch on the center console
or outer switch on the back door.
OPERATING FROM INSIDE
The ignition key must be in the ONº posi-
tion.
The back window moves as long as you
hold the inner switch.
To open: Push the switch on the
º
side.
To close: Push the switch on the
º
side.You can also open the back window when
the back window wiper is working. At that
time, the wiper stops working until the
window is closed again.
If you push in the window lock switch on
the driver 's door (with power windows) or
on the instrument panel (without power
windows), the back window cannot be op-
erated.
With power windows (driver's door)
Without power windows
(instrument panel)
ProCarManuals.com
Page 103 of 279
292000 4Runner (OM35762U)
3. Hold the hood open by inserting the
support rod into the slot.
Before closing the hood, check to see that
you have not forgotten any tools, rags,
etc. and return the support rod to its
clipÐthis prevents rattles. Then lower the
hood make sure it locks into place. If
necessary, press down gently on the front
edge to lock it.
CAUTION
After inserting the support rod into
the slot, make sure the rod supports
the hood security from falling down
on to your head or body.
Theft deterrent system
To deter the vehicle theft, the system
is designed to give an alarm if any of
the side doors, back door or hood is
forcibly unlocked or opened or the bat-
tery terminal is disconnected and then
reconnected when the vehicle is locked.
The alarm blows the horn intermittently
and flashes the headlights and tail lights.SETTING THE SYSTEM
1. Turn the ignition key to the LOCKº
position and remove it.
The indicator light will start flashing every
2 seconds when the key is removed from
the ignition switch. (See Engine
immobiliser systemº for details.)
2. Have all passengers get out of the
vehicle.
3. Close and lock all the side doors, back
door and hood.
The indicator light will come on when all
the side doors, back door and hood are
closed and locked.
ProCarManuals.com
Page 104 of 279
302000 4Runner (OM35762U)
The system will automatically be set after
30 seconds. When the system is set, the
indicator light will start flashing again.
4. After making sure the indicator light
starts flashing, you may leave the ve-
hicle.
Never leave anyone in the vehicle when
you set the system, because unlocking
from the inside will activate the system.
WHEN THE SYSTEM IS SET
Activating the system
The system will give the alarm under the
following conditions:
If any of the side doors is unlocked or
opened without the key or wireless re-
mote control transmitter, or if the back
door or hood is forcibly opened
If the battery terminal is disconnected
and then reconnected
The indicator light will come on when the
system is activated.If the alarm has been activated and the
key is not in the ignition switch, all the
side doors and back door will re- lock au-
tomatically.
After one minute, the alarm will automati-
cally stop and the indicator light will starts
flashing again.
Reactivating the alarm
Once set, the system automatically resets
the alarm after the alarm stops.
The alarm will activate again under the
same circumstances described in
Activating the systemº.
Stopping the alarm
The alarm will be stopped by the following
three ways:
Turn the ignition key from the LOCKº
to ONº position.
Unlock any of the side doors or back
door with the key or wireless remote
control transmitter.
These ways cancel the system at the
same time.TESTING THE SYSTEM
1. Open all the windows.
2. Set the system as described above.
The side doors and back door should
be locked with the key or wireless re-
mote control transmitter. Be sure to
wait until the indicator light goes off or
starts flashing.
3. Unlock any side door from the inside.
The system should activate the alarm.
4. Stopping the alarm as described above.
5. Repeat this operation for the other
doors and hood. When testing on the
hood, also check that the system is
activated when the battery terminal is
disconnected and then reconnected.
If the system does not work properly,
have it checked by your Toyota dealer.
ProCarManuals.com
Page 106 of 279
322000 4Runner (OM35762U)
Electric moon roof
Sliding operation
Tilting operationTo operate the moon roof, use the
switch beside the personal lights.
The moon roof works when the ignition
switch is in the ONº position.
Key off operationÐ
If all the doors are closed, it works for 43
seconds even after the ignition switch is
turned off. It stops working when any of
the doors is opened.
Sun shade operationÐ
The sun shade can be opened or closed
by hand.
Sliding operationÐ
To open: Push the switch on the º side.
The roof will fully open. To stop the roof
partway, push the switch on the º side.
The sun shade will be opened together
with the roof.
To close: Push the switch on the º
side.
As a precaution when closing, the roof
stops at the three- quarters closed position
before fully closing. Therefore, release the
switch and then push it again to close it
completely.Tilting operationÐ
To tilt up: Push the switch on the TILT
UPº side.
To lower: Push the switch on the TILT
DOWNº side.
You may stop the moon roof at any de-
sired position. The roof will move while
the switch is being pushed and stop when
released.
CAUTION
To avoid serious personal injury, you
must do the following.
While the vehicle is moving, always
keep the head, hands and other
parts of the body of all occupants
away from the roof opening. Other-
wise, you could be seriously injured
if the vehicle stops suddenly or if
the vehicle is involved in an acci-
dent.
ProCarManuals.com
