2000 SUZUKI SWIFT shaft

7A-32 MANUAL TRANSMISSION
3) Drive in new differential pinion shaft pin (2) till the depth from
differential case (3) surface is about 1 mm (0.04 in.).
4) Press-fit new sensor rotor (1) with groove (4) side downward
as shown by using special tools and copper hammer.
Special tool
(A) : 09913-75510
(B) : 09940-54910
5) Press-fit left bearing by using special tools and copper ham-
mer.
6) Support differential assembly (1) as illustrated so as to left
bearing (2) is floating, and then press-fit right bearing (3) like
left bearing in Step 5).
Special tool
(C) : 09951-76010
(D) : 09951-16060
7) Hold differential assembly with soft jawed vise (3), install final
gear (2) as shown in figure and then tighten bolts (1) with
thread lock cement applied to specified torque.
“A” : Thread lock cement 99000-32110
Tightening torque
Final gear bolts (a) : 90 N·m (9.0 kg-m, 65.0 lb-ft)
NOTE:
Make sure to install final gear in correct installing direc-
tion.
CAUTION:
Use of any other bolts than specified ones is prohibited.
4. Groove

MANUAL TRANSMISSION 7A-33
UNIT ASSEMBLY
DIFFERENTIAL TO LEFT CASE
ASSEMBLY
1) Install differential assembly (1) into right case (2).
2) Insert VSS (3) with grease applied to its O-ring, then tighten
it with bolt.
Grease 99000-25010
3) Join input shaft (5), countershaft (4), low speed gear shift
shaft (2) and high speed gear shift shaft (3) assemblies all
together, then install them into right case (1).
4) Install 5th & reverse gear shift shaft (1) with 5th & reverse
gear shift guide shaft (2) into right case (5). Reverse gear
shift arm (4) has to be joined with reverse gear shift lever (3)
at the same time.
5) Place reverse gear shift lever, fasten it with bolts after apply-
ing thread lock cement.
“A” : Thread lock cement 99000-32110
Tightening torque
Revers gear shift lever bolts
(a) : 23 N·m (2.3 kg-m, 17.0 lb-ft)
Distance between lever end and shaft bore
“a” : 5 mm (0.2 in.)
CAUTION:
Take care not to damage oil seal lip by input shaft, or oil
leakage may take place.
NOTE:
 Input shaft right bearing on shaft can be installed into
right case by tapping shaft with plastic hammer.
 Check to make sure that counter shaft is engaged with
final gear while installing.
NOTE:
 When installing reverse gear shift lever, set it as the
following specification.

7A-34 MANUAL TRANSMISSION
6) Make reverse idler gear (1) with reverse gear shift lever (2),
insert reverse gear shaft (3) into case through idler gear and
then align “A” in shaft with “B” in case.
7) Clean mating surfaces of both right and left cases, apply
sealant to right case (2) by using a nozzle as shown in figure
by such amount that its section is 1.5mm (0.059 in.) in diam-
eter then mate it with left case (1).
“B” : Sealant 99000-31110
8) Tighten case bolts (3) from left case side to specified torque.
Tightening torque
Transmission case bolts (b) : 19 N·m (1.9 kg-m, 14.0 Ib-ft)
9) Install reverse shaft bolt (4) to which thread lock cement
have been applied with aluminum washer and tighten it.
“A” : Thread lock cement 99000-32110
Tightening torque
Reverse shaft bolt (c) : 23 N·m (2.3 kg-m, 17.0 lb-ft)
10) Install another case bolts from clutch housing side and
tighten them to specification. NOTE:
 Distance “a” can be measured by installing reverse
gear shaft provisionally.
 When “a” is 5 mm (0.2 in.), clearance between reverse
idler gear groove and shift lever end will be 1 mm (0.04
in.).
NOTE:
 Make sure that washer (4) has been installed in shaft at
above the gear.
 Check to confirm that reverse gear shift lever end has
clearance 1 mm (0.04 in.) to idler gear groove.

MANUAL TRANSMISSION 7A-35
11) Check locating spring for deterioration and replace with new
one as necessary.
Locating spring free length
For Low speed (3) and 5th & reverse (6)
Standard : 26.1 mm (1.028 in.)
Service Limit : 25.0 mm (0.984 in.)
For High speed (5)
Standard : 40.1 mm (1.579 in.)
Service Limit : 39.0 mm (1.535 in.)
12) Install steel ball (4) and locating spring for respective gear
shift shaft and tighten bolt (1) to which sealant have been
applied to its thread part.
Sealant 99000-31110
Tightening torque
Locating spring bolts (d) : 13 N·m (1.3 kg-m, 9.5 Ib-ft)
FIFTH GEARS
1) To seat countershaft left bearing cup (1) to bearing cone, tap
cup by using special tool and plastic hammer.
Special tool
(A) : 09913-84510
2) Put a shim (2) on bearing cup (3) provisionally, place straight
edge (1) over it and compress it by hand through straight
edge, and then measure “a” (Clearance between case sur-
face (4) and straight edge) by using feeler gauge (5).
Clearance between case surface and straight edge
“a” : 0.13 – 0.17 mm (0.0051 – 0.0067 in.)
(Shim protrusion)
3) By repeating above step, select a suitable shim which
adjusts clearance “a” to specification and put it on bearing
cup.
2. Washer
NOTE:
Insert 0.15 mm (0.0059 in.) feeler to know whether or not
a shim fulfills specification quickly.

7A-36 MANUAL TRANSMISSION
Available shim thickness
0.40, 0.45, 0.50, 0.55, 0.6, 0.65,0.7, 0.75, 0.8, 0.85, 0.9, 0.95,
1.0,1.05, 1.1 and 1.15 mm (0.015, 0.017, 0.019, 0.021,
0.023,0.025, 0.027, 0.029, 0.031, 0.033,0.035, 0.037, 0.039,
0.041, 0.043 and 0.045 in.)
4) Place left case plate (2) inserting its end in groove of shift
guide shaft (4) and tighten new adhesive pre-coated
screw(s) (1) (and new adhesive per-coated bolts (7) tempo-
rarily with less than specified toque.
5) Tighten new screw(s) (and new bolts) to specified torque
finally in the order of circled numbers (➀→➁→➂→➃→➄→➅
) shown in figure.
Tightening torque
Left case plate screw(s) (and bolts)
(a) : 11 N·m (1.1 kg-m, 8.0 lb-ft)
6) Assemble 5th speed synchronizer sleeve (4) and hub (3)
with keys (2) and springs (1).
Synchronizer key installation position
: A = B
7) Install 5th gear (1) to counter shaft facing machined boss A
inward. CAUTION:
Do not reuse left case plate screw(s) (1) (and bolts (7)).
Be sure to use new adhesive pre-coated screw(s) (and
new adhesive pre-coated bolts). Otherwise, screw(s)
(and/or bolts) may loosen.
NOTE:
After tightening screw(s) (and bolts), make sure that
countershaft (5) can be rotated by hand feeling certain
load.
[A]: In case 6 screws are used 3. Input shaft
[B]: In case 1 screw and 5 bolts are used 6. Transaxle left case
NOTE:
Short side C in keys, long flange D in hub and chamfered
spline F in sleeve should face inward (5th gear side).
[A] : Short side C D : Long flange (Inward)
[B] : Long side E : Key way
C : Short side (Inward) F : Chamfered spline (Inward)
A : Machined boss (Inside)
B : No machining (Outside)

MANUAL TRANSMISSION 7A-37
8) Install needle bearing of separated steel cage type to input
shaft, apply oil then install 5th gear (1) and special tool to
stop shaft rotation.
Special tool
(B) : 09927-76010
9) Install new countershaft nut (2) and tighten it to specification.
Tightening torque
Countershaft nut (b) : 60 N·m (6.0 kg-m, 43.5 lb-ft)
10) Remove special tool, then caulk nut at C with caulking tool
and hammer.
11) Install synchronizer ring (2).
12) Fit 5th gear shift fork (1) to sleeve & hub assembly (3) and
install them into input shaft, shift shaft and shift guide shaft at
once aligning hub oil groove A with shaft mark B.
13) Drive in spring pin facing its slit A outward.
14) If equipped, install steel ball, tighten shift fork plug (3) to
which thread lock cement have been applied.
“A” : Thread lock 1322 99000-32110
Tightening torque
5th shift fork plug (c) : 10 N·m (1.0 kg-m, 7.5 lb-ft)
15) Fit hub plate (1) and fix it with circlip (2).
16) If equipped, install circlip (4) to the end of 5th & reverse gear
shift guide shaft.
NOTE:
Long flange of hub faces inward (gear side).
A : Oil groove (Align with B)
B : Punch mark
C : Caulking
CAUTION:
 Coat shift fork plug with thread lock cement reason-
ably. If it is done to much, excess may interfere in ball
movement and cause hard shift to 5th speed.
 Make sure circlip is installed in shaft groove securely.
A : Pin slit (Face outward)

7A-38 MANUAL TRANSMISSION
17) Clean mating surface of both left case (2) and side cover (1),
apply sealant to side cover (1) by using a nozzle as shown in
figure by such amount that its section is 1.5mm (0.059 in.) in
diameter, mate it with left case and then tighten bolts.
“B” : Sealant 99000-31110
Tightening torque
Side cover No.1 bolts (a) : 10 N·m (1.0 kg-m, 7.5 lb-ft)
Side cover No.2 bolts (b) : 23 N·m (2.3 kg-m, 17.0 lb-ft)
GEAR SHIFT AND SELECT SHAFT ASSEMBLY
1) Clean mating surface of guide case.
2) Apply grease to select lever shaft bush and select lever
boss, and install gear shift and select shaft assembly with
new gasket into transmission.
“A” : Grease 99000-25010
3) Apply sealant to gear shift guide case No. 2 bolt (5). Tighten
gear shift guide case No. 1 bolts (1) and No. 2 bolt (5) to
specified torque at the position that clearance “a” is within 1 -
1.5 mm (0.04 - 0.06 in.).
Tightening torque
Guide case bolts (a) : 23 N·m (2.3 kg-m, 17.0 lb-ft)
4) Install washer and gear shift interlock bolt (2) to which seal-
ant have been applied and them tighten it to specified
torque.
“B” : Sealant 99000-31110
Tightening torque
Gear shift inter lock bolt (a) : 23 N·m (2.3 kg-m, 17.0 lb-ft)
5) Install washer and 5th to reverse interlock guide bolt (3) to
which sealant have been applied and then tighten it to speci-
fied torque.
“B” : Sealant 99000-31110
Tightening torque
5th to reverse interlock guide bolt (a) : 23 N·m (2.3 kg-m,
17.0 lb-ft)

MANUAL TRANSMISSION 7A-39
6) Tighten backup lamp switch (1) to specified torque.
Tightening torque
Backup lamp switch (b) : 19 N·m (1.9 kg-m, 14.0 lb-ft)
7) Check input shaft for rotation in each gear position.
8) Also confirm function of back up light switch in reverse posi-
tion by using ohmmeter.
TIGHTENING TORQUE SPECIFICATION
Fastening partTightening torque
Nm kg-m lb-ft
Transmission oil level/filler and drain plugs 21 2.1 15.5
Oil gutter bolt 10 1.0 7.5
Final gear bolts 90 9.0 65.0
Reverse gear shift lever bolts 23 2.3 17.0
Transmission case bolts 19 1.9 14.0
Reverse shaft bolt 23 2.3 17.0
Locating spring bolts 13 1.3 9.5
Left case plate screw 9 0.9 6.5
Countershaft nut 60 6.0 43.5
5th shift fork plug 10 1.0 7.5
Side cover No.1 bolts 10 1.0 7.5
Side cover No.2 bolts 23 2.3 17.0
Guide case bolts 23 2.3 17.0
Gear shift interlock bolt 23 2.3 17.0
5th to reverse interlock guide bolt 23 2.3 17.0
Backup lamp switch 19 1.9 14.0