2000 SUZUKI GRAND VITARA Manual transmission

YH4
GRAND
VITARA
7B1-78 AUTOMATIC TRANSMISSION (4 A / T)
ON-VEHICLE
SERVICE MOUNTING
EXTERNAL
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
Fastening portion
Tightening torque
Fastening portion
N´mkg-mlb-ft
Automatic transmission fluid drain plug232.317.0
Transfer oil filler / level and drain plugs232.317.0
Transmission case plug171.712.5
Manual select lever nut131.39.5
Manual select cable nut70.75.5
Manual selector assembly bolts181.813.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts
Engine rear mounting member bolts
Transmission case right stiffener bolts
505.036.5
Universal joint flange bolts and nuts505.036.5
Torque converter mounting bolts656.547.0
Adapter case or extension case bolts
(G16 engine)353.525.5
Adapter case or extension case bolts
(J20 / H25 engines)424.230.0
Transmission range switch lock bolt5.50.554.0
Oil pipe union bolts353.522.5
Drive plate bolts787.856.5
Interlock cable clamp screw2.20.221.5
Interlock cable outer mounting nut131.39.5

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-79
09925-37810
Oil pressure gauge09927-56010
Gear stopper
(only for G16 / J20)09931-76030
16 / 14 pin DLC
(OBD-II adapter) cable
09931-76011
SUZUKI scan tool (Tech 1A) kit1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
5. Test lead / probe
6. Power source cable
7. DLC cable adapter
8. Self±test adapterMass storage cartridge
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
A / T fluidAn equivalent of DEXRON-III
Automatic transmission

Parts lubrication when installing
Lithium greaseSUZUKI SUPER GREASE A
(99000±25010)
Cable ends
SealantSUZUKI BOND NO.1215
(99000-31110)
Flywheel bolts
SPECIAL TOOLS

YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
1. Wood block
2. Dash panel
t: 45 mm / 1.8 in.
H: 200 mm / 8 in.
W: 100 ± 150 mm / 4 ± 6 in.
1. Transmission jack
2. Engine rear mounting member
3. Gear shift lever case
4. Bolt
TRANSFER 7D-5
TRANSFER ASSEMBLY
Dismounting and remounting of transfer and transmission together
as a unit is described in Section 7A for Manual Transmission or 7B1
for Automatic Transmission, but it is also possible to dismount and
remount transfer assembly by itself as described below.
DISMOUNTING
IN ENGINE ROOM
1) Disconnect negative (±) cable from battery.
2) Remove distributor assembly (if equipped).
3) Place wood block between engine and dash panel so that it
serves as stopper when engine, transmission and transfer unit
hangs down as rear mounting member is removed.
CAUTION:
Make sure to use wood block to prevent contact which
may occur between dash panel and CMP sensor case
(G16), CMP sensor (J20) or intake manifold (H25), and fan
and shroud.
IN CABIN
1) Remove console box.
2) Remove shift lever of transmission and transfer.
ON LIFT
1) Drain transfer oil.
2) Remove rear propeller shaft.
3) Remove front propeller shaft.
4) Disconnect exhaust center pipe.
5) Disconnect speed sensor coupler.
6) Place transmission jack and remove mounting member.
7) Lower transmission jack gradually and check to ensure that
wood block serves as stopper between engine and dash panel.
8) Remove bolts for gear shift lever case.
9) Pull off breather hose.