Page 565 of 801
YH4
GRAND
VITARA
Type B Type A
Type C
1. Washer tank
8D-10 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) Testing automatic stop action.
a) Connect 12 V battery (+) terminal to terminal ªAº of wiper mo-
tor (1) and (±) terminal to Black lead wire (2) (Type A, B) or
terminal ªEº (Type C), and let the motor turn.
b) Disconnect terminal ªAº from battery, and let the motor stop.
c) Connect terminal ªAº and ªDº with a jumper wire (3), and con-
nect terminal ªCº to battery (+) terminal. Observe the motor
turns once again then stops at a given position.
d) Repeat a) thru c) several times and inspect if the motor stops
at the given position every time.
Washer Pump
Connect battery (+) and (±) terminals to pump (+) and (±) terminals
respectively to check pumping rate.
Check for both front (3) and rear (2) (if equipped) washer pump.
Pumping Rate:
Front and Rear (if equipped) more than 1.0 l / min.
(2.1 US pt. / min.,
1.76 lmp pt. / min.).
Page 566 of 801

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-11
SLOW
FAST
10 ± 14 V
0 V
1.6 1 sec.
10 ± 14 V
0 V
10.7 5 sec.
Intermittent Wiper Relay Circuit
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Turn the front wiper switch to INT position.
4) Turn the intermittent time control switch to FAST position.
5) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
6) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
Check that the voltmeter indicates the battery voltage (10 ±
14 V).
7) Connect terminal ªAsº and terminal ªB3º by a jumper wire. Then
move jumper wire end connected to terminal ªB3º to terminal ªEº.
Observe the voltmeter voltage drops to 0 V right after connecting
the jumper wire from terminal ªB3º to ªEº. Then the voltage rises
to battery voltage (10 ± 14 V) within the time shown in the table
below.
INT time control
switch position
Voltage
FAST
SLOW
Page 567 of 801
YH4
GRAND
VITARA
WASHER
ONON
OFF
10 ± 14V
0VApprox. 2.5 sec.
Approx. 0.5 sec.
8D-12 WINDOWS, MIRRORS, SECURITY AND LOCKS
Washer Linked Operation
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Make sure that front wiper switch is at OFF position.
4) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
5) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
6) Pull washer switch and check that voltage changes as shown in
the table.
Washer switch
Voltmeter
Page 568 of 801
YH4
GRAND
VITARA
Terminal
Switch
Terminal
Switch
ON
INT
WASHER
ON
BRINT
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-13
REAR WIPER AND WASHER (IF EQUIPPED)
INSPECTION
Rear Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
Rear Wiper Switch
BRINT+IRBRINT+IR
OFF
INT
ON
Rear Washer Switch
BRWRBRWR
OFF
ON
Washer Pump
Refer to FRONT WIPER AND WASHER INSPECTION in this sec-
tion.
Wiper Motor
1) TESTING WIPER MOTOR
As shown left, use a 12 V battery to connect its (+) and (±) termi-
nals to terminal ªDº and Black lead wire (2) respectively. Then
motor (1) should rotate at 35 to 45 rpm.
Page 569 of 801

YH4
GRAND
VITARA
8D-14 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) TESTING AUTOMATIC STOP ACTION
a) First, connect battery (+) terminal to terminal ªDº and battery
(±) terminal to black lead wire (2) and let the motor (1) turn.
b) Then disconnect terminal ªDº from battery and let the motor
stop.
c) Next connect terminal ªDº and terminal ªAº with a jumper wire
(3) and connect terminal ªBº to battery (+) terminal. Observe the
wiper motor turns once again, then stops at a given position.
d) Repeat these steps several times, and inspect if the motor
stops at the given position every time.
Rear Wiper Intermittent Relay
[ON circuit]
1) Connect positive terminal of battery to terminals ª1º and ª4º of
relay, negative terminal to terminal ª5º of relay and check voltage
between terminals ª6º and ª5º of relay.
If measured voltage is battery voltage, relay is in good condition.
If not, replace relay.
2) Connect positive terminal of battery to terminal ª2º of relay, then
disconnect positive terminal from terminal ª4º of relay and check
voltage between terminals ª6º and ª5º of relay.
If measured voltage is battery voltage, relay is in good condition.
If not, replace relay.
3) Disconnect positive terminal from terminal ª2º of relay and check
voltage between terminals ª6º and ª5º of relay.
If measured voltage is about 0 V, relay is in good condition.
If not, replace relay.
[WASH circuit]
1) Connect positive terminal of battery to terminal ª1º of relay and
negative terminal to terminal ª5º of relay. Then connect positive
terminal to terminal ª7º checking voltage between terminals ª6º
and ª5º of relay.
If measured voltage changes from about 0 V to battery voltage
0.6 to 1.5 seconds after connecting positive terminal to terminal
ª7º, relay is in good condition. If not, replace relay.
Page 570 of 801

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-15
2) Disconnect positive terminal from terminal ª7º checking voltage
between terminal ª6º and ª5º of relay.
If measured voltage changes from battery voltage to about 0 V
2.7 to 4.6 seconds after disconnecting positive terminal from ter-
minal ª7º, relay is in good condition.
If not, replace relay.
[INT circuit]
1) Connect positive terminal of battery to terminals ª1º of relay and
negative terminal to terminal ª5º of relay. Then positive terminal
to terminal ª3º of relay checking voltage between terminals ª6º
and ª5º of relay.
If measured voltage changes from about 0 V to battery voltage
when connecting positive terminal to terminal ª3º, relay is in
good condition.
If not, replace relay.
2) Connect positive terminal of battery to terminal ª2º of relay, then
disconnect positive terminal from terminal ª2º of relay checking
voltage between terminals ª6º and ª5º of relay.
If measured voltage changes from battery voltage to about 0 V
when disconnecting positive terminal from terminal ª2º and
about 0 V to battery voltage 8 2 seconds after disconnecting
positive terminal from terminal ª2º, relay is in good condition.
If not, replace relay.
Page 571 of 801

YH4
GRAND
VITARA
1. Heat wire
2. Tin foil
3. Tester probe
1. VoltmeterAt center
Good
Broken
wire
broken
wire
8D-16 WINDOWS, MIRRORS, SECURITY AND LOCKS
REAR WINDOW DEFOGGER (IF EQUIPPED)
INSPECTION
DEFOGGER SWITCH
Check for continuity between terminals at each switch position as
shown below.
If check result is not as specified, replace switch.
DEFOGGER WIRE
NOTE:
When cleaning rear window glass, use a dry cloth to wipe it
along wire direction.
When cleaning glass, do not use detergent or abrasive-con-
taining glass cleaner.
When measuring wire voltage, use a tester with negative
probe wrapped with a tin foil which should be held down on
wire by finger pressure.
1) Checking wire damage
a. Turn main switch ON.
b. Turn defogger switch ON.
c. Use a voltmeter to check voltage at the center of each heat
wire, as shown.
Voltage
Criteria
Approx. 5 VGood (No break in wire)
Approx. 10 V or 0 VBroken wire
If measured voltage is 10 V, wire must be damaged between
its center and positive end. If voltage is zero, wire must be
damaged between its center and ground.
Page 573 of 801
YH4
GRAND
VITARA
Type 1
Type 2
LH steering vehicle
Terminal
Switch
Terminal
Switch
8D-18 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER WINDOW CONTROL SYSTEM
INSPECTION
POWER WINDOW MAIN SWITCH
Check switch for continuity between terminals as shown below.
Type 1
WindowDriver SidePassenger SideWindowLockWindow Switch (2)gWindow Switch (3)LockSwitch (1)CHGACEBAAF
UPUP
OFFOFFOFFOFF
DOWNDOWN
UPUP
ONOFFONOFF
DOWNDOWN
Type 2 LH steering vehicle
Window
Lock
Switch (1)
Driver
Side
Window
Switch (2)Passenger
Side
Window
Switch (3)Rear RH
Window
Switch (4)Rear LH
Window
Switch (5)
Switch (1)
KCABKCEFKCIJKCGHKCABKCEFKCIJKCGH
UPUP
OFFOFFOFFOFF
DOWNDOWN
UPUP
ONOFFONOFF
DOWNDOWN