2000 SUZUKI GRAND VITARA Washer

YH4
GRAND
VITARA
Type B Type A
Type C
1. Washer tank
8D-10 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) Testing automatic stop action.
a) Connect 12 V battery (+) terminal to terminal ªAº of wiper mo-
tor (1) and (±) terminal to Black lead wire (2) (Type A, B) or
terminal ªEº (Type C), and let the motor turn.
b) Disconnect terminal ªAº from battery, and let the motor stop.
c) Connect terminal ªAº and ªDº with a jumper wire (3), and con-
nect terminal ªCº to battery (+) terminal. Observe the motor
turns once again then stops at a given position.
d) Repeat a) thru c) several times and inspect if the motor stops
at the given position every time.
Washer Pump
Connect battery (+) and (±) terminals to pump (+) and (±) terminals
respectively to check pumping rate.
Check for both front (3) and rear (2) (if equipped) washer pump.
Pumping Rate:
Front and Rear (if equipped) more than 1.0 l / min.
(2.1 US pt. / min.,
1.76 lmp pt. / min.).

YH4
GRAND
VITARA
WASHER
ONON
OFF
10 ± 14V
0VApprox. 2.5 sec.
Approx. 0.5 sec.
8D-12 WINDOWS, MIRRORS, SECURITY AND LOCKS
Washer Linked Operation
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Make sure that front wiper switch is at OFF position.
4) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
5) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
6) Pull washer switch and check that voltage changes as shown in
the table.
Washer switch
Voltmeter

YH4
GRAND
VITARA
Terminal
Switch
Terminal
Switch
ON
INT
WASHER
ON
BRINT
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-13
REAR WIPER AND WASHER (IF EQUIPPED)
INSPECTION
Rear Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
Rear Wiper Switch
BRINT+IRBRINT+IR
OFF
INT
ON
Rear Washer Switch
BRWRBRWR
OFF
ON
Washer Pump
Refer to FRONT WIPER AND WASHER INSPECTION in this sec-
tion.
Wiper Motor
1) TESTING WIPER MOTOR
As shown left, use a 12 V battery to connect its (+) and (±) termi-
nals to terminal ªDº and Black lead wire (2) respectively. Then
motor (1) should rotate at 35 to 45 rpm.

YH4
GRAND
VITARA
BODY SERVICE 9-21
1. Hood lock
2. Hood lock bolts
3. Match marks
1. Hood cushion
HOOD
REMOVAL
1) Remove window washer hose from hood.
2) Remove four mounting bolts to detach hood.
ADJUSTMENT

Fore-and-aft and right-and-left adjustment.
Loosen four mounting bolts for adjustment.

Hood lock adjustment
When installing hood lock, bring bolt at intersection point of match
marks and move it in vertical direction for adjustment, if neces-
sary.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

Vertical adjustment
If only one side (right or left) of hood is not level with front fender,
make it level by tightening or loosening hood cushion.
INSTALLATION
Reverse removal procedure to install hood.
INSPECTION
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.) Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.

YH4
GRAND
VITARA
BODY SERVICE 9-73
5
46
4. Assistant grip
5. Rear room light
6. Inner trim
1. Roof harness
2. Rear washer hose
3. Adhesive tape
Front 1. Room light
2. Sunshade assembly
3. Spot light
IWATA
CAMI
HEAD LINING
REMOVAL
1) Remove spot light and sliding roof switch (if equipped).
2) Remove sunshade assembly.
3) Remove room light and spacer.
4) Remove assistant grips.
5) Remove inner trims covering head lining and door opening trim.
6) Remove rear speaker cover (if equipped).
7) Disconnect rear washer hose and roof harness from body.
8) Remove head lining.
NOTE:
Adhesive double coated tape is used to attach rear part of
head lining. Detach head lining from roof after removing all
above parts.
INSTALLATION
1) Set roof harness and washer hose to head lining with tape.
2) Clean roof where adhesive tape of head lining will be attached.
3) Peel off release liner of adhesive tape on head lining and install
it to body.
4) Install assistant grips a, b, c and d in that order.