2000 SUZUKI GRAND VITARA Brake master cylinder

YH4
GRAND
VITARA
Diagnostic Trouble Code (DTC) Table 5E1-14. . .
System Circuit 5E1-15. . . . . . . . . . . . . . . . . . . . . . .
Table ± A ªABSº Warning Lamp Circuit
Check ± Lamp does not come ªONº
at ignition switch on 5E1-16. . . . . . . . . . . . . . . . . .
Table ± B ªABSº Warning Lamp Circuit
Check ± Lamp comes ªONº steady 5E1-17. . . .
Table ± C ªABSº Warning Lamp Circuit
Check ± The lamp flashes continuously
while ignition switch is on5E1-18 . . . . . . . . . . . . . .
Table ± D Code (DTC) is not Outputted
even with Diag. Switch Terminal
Connected to Ground 5E1-19. . . . . . . . . . . . . . . .
Table ± E EBD Warning Lamp (Brake
Warning Lamp) Check-lamp Comes
ªONº Steady 5E1-20. . . . . . . . . . . . . . . . . . . . . . . .
DTC 15 ± G Sensor Circuit 5E1-21. . . . . . . . . . . .
DTC 21, 22, 25, 26, 31, 32, 35 or 36
± Wheel Speed Sensor Circuit 5E1-23. . . . . . . .
DTC 41, 45 or 56 ± Solenoid Circuit 5E1-26. . . . .
DTC 57 ± Solenoid and Pump Motor
Power Source Circuit 5E1-27. . . . . . . . . . . . . . . .
DTC 61 ± ABS Pump Motor Circuit 5E1-28. . . . . .
DTC 63 ± ABS Fail-Safe Relay Circuit 5E1-29. . .
DTC 71 ± ABS Control Module 5E1-30. . . . . . . . .
ON-VEHICLE SERVICE5E1-31 . . . . . . . . . . . . . . . .
Precaution 5E1-31. . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS Hydraulic Unit Operation Check 5E1-31. . . .
ABS Hydraulic Unit / Control Module
Assembly 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic unit inspection 5E1-32. . . . . . . . . . . . . Removal 5E1-32. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-33. . . . . . . . . . . . . . . . . . . . . . . . .
Front Wheel Speed Sensor 5E1-34. . . . . . . . . . . .
Output voltage inspection 5E1-34. . . . . . . . . . . .
Removal 5E1-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-35. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-35. . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Front Sensor Rotor 5E1-36. . . . . . . . . . . . . . . . . . .
Removal 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-36. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wheel Speed Sensor 5E1-37. . . . . . . . . . . .
Output voltage inspection 5E1-37. . . . . . . . . . . .
Removal 5E1-37. . . . . . . . . . . . . . . . . . . . . . . . . .
Sensor inspection 5E1-38. . . . . . . . . . . . . . . . . .
Sensor rotor inspection 5E1-38. . . . . . . . . . . . . .
Installation 5E1-38. . . . . . . . . . . . . . . . . . . . . . . . .
Rear Sensor Rotor 5E1-39. . . . . . . . . . . . . . . . . . . .
Removal 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-39. . . . . . . . . . . . . . . . . . . . . . . . .
G Sensor 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5E1-40. . . . . . . . . . . . . . . . . . . . . . . . .
Transfer 4WD Switch 5E1-41. . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS5E1-41 . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5E1-42 . . . . . . . . . . . . . . . . . . . . . .
5E1-2 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
GENERAL DESCRIPTION
The ABS (Antilock Brake System) controls the fluid pressure applied to the wheel cylinder of each brake from the
master cylinder so that each wheel is not locked even when hard braking is applied. This ABS is a 4-wheel type
which controls the fluid pressure applied to the wheel cylinder of each of the four brakes to prevent each wheel
from getting locked.
The component parts of this ABS includes following parts in addition to those of the conventional brake system.

Wheel speed sensor which senses revolution speed of each wheel and outputs its signal.

In this ABS, ABS hydraulic unit (actuator assembly), ABS control module, pump motor relay and fail-safe relay
are combined as one component.

ABS control module which sends operation signal to ABS hydraulic unit to control fluid pressure applied to each
wheel cylinder based on signal from each wheel speed sensor so as to prevent wheel from locking.

ABS hydraulic unit which operates according to signal from ABS control module to control fluid pressure applied
to wheel cylinder of each of 4 wheels.

Fail-safe (solenoid valve) relay which supplies power to solenoid valve in ABS hydraulic unit and pump motor
relay.

Pump motor relay which supplies power to pump motor in ABS hydraulic unit.

ªABSº warning lamp which lights to inform abnormality when system fails to operate properly.

G sensor which detects body deceleration speed. (For 4WD model only)
This ABS is equipped with Electronic Brake force Distribution (EBD) system that controls a fluid pressure of rear
wheels to best condition, which is the same function as that of proportioning valve, by the signal from wheel sensor
independently of change of load due to load capacity and so on. And if the EBD system fails to operate properly,
the brake warning lamp lights to inform abnormality.

YH4
GRAND
VITARA
1. Front disk brake
2. Rear drum brake
3. ABS hydraulic unit / control module assembly
with ABS pump motor
relay and fail-safe relay
4. Brake master cylinder / Reservoir
LH steering vehicle
RH steering vehicle
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-3
BRAKE HOSE / PIPE ROUTING

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-33
1. ABS hydraulic unit /
control module
assembly
2. Nut
1. To left-front
2. To right-front
3. To rear
4. From master cylinder4) Remove three nuts and take out ABS hydraulic unit / control
module assembly from bracket.
CAUTION:

Do not give an impact to hydraulic unit.

Use care not to allow dust to enter hydraulic unit.

Do not place hydraulic unit on its side or upside down.
Handling it in inappropriate way will affect its original
performance.
INSTALLATION
1) Install hydraulic unit by reversing removal procedure.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 12.0 lb-ft)
(b): 21 N
.m (2.1 kg-m, 15.5 lb-ft)
(c): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
2) Bleed air from brake system. Refer to ªBLEEDING BRAKESº in
Section 5.
3) Check each installed part for fluid leakage and perform hydraulic
unit operation check.

YH4
GRAND
VITARA
1. Clutch pedal
2. Clevis lock nut
3. Push rod
1. Clutch master cylinder
2. Clutch pipe
3. Clutch hose
4. Clutch operating cylinder
1. Pipe
2. Hose
3. Spanner
4. Flare nut wrench2, (a)
7C1-4 CLUTCH
ON-VEHICLE SERVICE
CLUTCH PEDAL HEIGHT
Adjust clutch pedal height by loosening clevis lock nut and turning
push rod as shown.
Clutch pedal height is normal if clutch pedal is about
20 mm (0.79 in.) higher than brake pedal.
After adjusting, tighten lock nut to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
CLUTCH PEDAL FREE TRAVEL
Depress clutch pedal, stop the moment clutch resistance is felt and
measure distance (clutch pedal free travel). Free travel should be
within following specification.
Pedal free travel ªaº: 15 ± 25 mm (0.6 ± 1.1 in.)
CLUTCH FLUID PIPE AND HOSE
REMOVAL
NOTE:
Do not allow fluid to get on painted surface.
1) Remove dust and dirt from each joint of hose and pipe to be dis-
connected and clean around reservoir cap.
2) Take out fluid with syringe or such.
3) Disconnect fluid pipe from hose.
NOTE:
To disconnect pipe from hose, separate them by using flare
nut wrench and spanner so as not to kink them.

YH4
GRAND
VITARA
1. Master cylinder
1. Attaching bolt
2. Attaching nut
3. Clevis pin
ªAº
7C1-6 CLUTCH
INSTALLATION
1) To bleed air from master cylinder itself, tilt it as shown in figure
and add fluid into it.
NOTE:
After bleeding air from master cylinder, plug pipe hole in it
to prevent fluid from spilling out of it till pipe is connected.
2) Install master cylinder assembly and new gasket to body, attach-
ing bolt, nuts and push rod clevis pin.
NOTE:
Do not reuse gasket.
3) Torque attaching bolt and nut to specification.
4) Connect fluid pipe and torque flare nut to specification.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
5) Apply grease to clevis pin and install it.
ªAº: Grease 99000-25010
6) Fill reservoir with specified brake fluid and check fluid leakage.
7) After installation, bleed air from system and check clutch pedal
free travel. Refer to BRAKE section for air bleeding procedure.
FLUID INSPECTION
Fluid level should be always between MIN and MAX lines on reser-
voir. If fluid decreases quickly, check for leakage, repair leaky point,
if any, and add fluid up to MAX level.
NOTE:

Brake fluid damages painted surface badly. Should it get on
painted surface, remove it immediately and clean surface
thoroughly.

Do not use shock absorber fluid or any other fluid which con-
tains mineral oil. Do not use container which has been used
for mineral oil or which is wet from water. Mineral oil will
cause swelling and distortion of rubber parts in hydraulic
clutch system and water will mix with brake fluid, lowering
fluid boiling point. Keep all fluid containers capped to pre-
vent contamination.

Make sure not to use fluid whose container cap was first
opened more than a year ago.

YH4
GRAND
VITARA
3
4
1. Reservoir cap
2. Cylinder
3. Piston assembly
4. Push rod
5. Piston stopper
6. Circlip
7. Boot
8. Lock nut
9. Clevis
1. Circlip
2. Push rod
3. Piston
4. Cylinder
1. Circlip
2. Push rod
3. Piston stopper
CLUTCH 7C1-7
DISASSEMBLY AND ASSEMBLY CLUTCH
MASTER CYLINDER
DISASSEMBLY
1) Remove boot and then circlip with piston pushed in.
2) Remove push rod and blow compressed air gradually into hole
for pipe connection to remove piston assembly, using care to
prevent it from jumping out.
INSPECTION
Inspect all disassembled parts for wear or damage and replace
parts if necessary.
NOTE:

Wash disassembled parts with brake fluid.

Do not reuse piston assembly and circlip.
Inspect cylinder bore for scoring or corrosion. It is best to replace
corroded cylinder. Corrosion can be identified as pits or excessive
roughness.
NOTE:
Polishing bore of cylinder with anything abrasive is prohib-
ited, as damage to cylinder bore may occur.
Rinse cylinder in clean brake fluid. Shake excess rinsing fluid from
cylinder. Do not use a cloth to dry cylinder, as lint from cloth cannot
be kept away from cylinder bore surfaces.
ASSEMBLY
NOTE:
Before installation, wash each part in specified brake fluid.
1) Apply brake fluid to inside of piston assembly and cylinder body.
2) Install piston assembly into cylinder.
3) With piston pushed down, install circlip as shown.
And install boot.

YH4
GRAND
VITARA
7C1-14 CLUTCH
09917-58010 (G16 engine)
09923-73210
(J20 and H25 engines)
Bearing remover09923-36330 (G16 engine)
09923-36320
(J20 and H25 engines)
Clutch center guide09924-17810
Flywheel holder09925-98210
Input shaft bearing installer
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mkg-mlb-ft
Flare nut161.611.5
Master cylinder nut131.39.5
Lock nut101.07.5
Flywheel boltsG16 engine787.856.5Flywheel boltsJ20 and H25 engines707.050.5
Clutch cover bolts232.316.5
Operating cylinder bolt505.036.5
Clutch hose union bolt232.316.5
REQUIRED SERVICE MATERIALS
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Lithium grease
SUZUKI SUPER GREASE A
(99000-25010)
Clutch master cylinder clevis pin.

Release fork.

Push rod tip of operating cylinder.
SUZUKI SUPER GREASE I
(99000-25210)Input shaft spline front end.
Clutch fluid
(Brake fluid)DOT3 or SAE J1703

Clutch reservoir.

Clutch master cylinder.

Clutch operating cylinder.
SealantSUZUKI BOND No.1215
(99000-31110)Flywheel bolts
SPECIAL TOOLS