2000 SUZUKI GRAND VITARA power steering pump

YH4
GRAND
VITARA
[D] [C] [A]
1. P / S pump pulley
2. A / C compressor
pulley (if equipped)
3. Crankshaft pulley
4. Tension pulley
5. Tension pulley bolts[A]: G16 type engine with A / C
[B]: G16 type engine without A / C
[C]: H25 type engine with A / C
[D]: H25 type engine without A / C
[B]
3B1-8 POWER STEERING (P / S) SYSTEM
POWER STEERING PUMP DRIVE BELT
NOTE:
For J20 Type engine, refer to Section 6H ªGENERATOR BELTº.
INSPECTION
Check that belt is free from any damage and properly fitted in pulley
groove.
BELT TENSION CHECK
Check belt tension by measuring how much it deflects when
pushed at intermediate point between pulleys with about 10 kg
(22 lb) force.
Deflection of P / S belt:
6 ± 9 mm (0.24 ± 0.35 in.) G16 Type engine. . . . . . . . . . . . . . . . .
4 ± 7 mm (0.16 ± 0.28 in.) H25 Type engine. . . . . . . . . . . . . . . . .
BELT TENSION ADJUSTMENT
[For G16 Type engine]
a) To adjust P / S pump drive belt tension, use adjusting bolt of com-
pressor for A / C equipped vehicles and that of P / S pump for ve-
hicles without A / C.
b) Adjust belt tension to above specification.
c) Then tighten adjusting and mounting bolts to specified torque.
[For J20 Type engine]
To adjust P / S pump drive belt tension, refer to ªGENERATOR
BELTº in Section 6H.
[For H25 Type engine]
a) To adjust P / S pump drive belt tension, loosen tension pulley
bolts and turn tension pulley using hexagon wrench.
b) Adjust belt tension to above specification.
Then tighten tension pulley bolts to specified torque.
Tightening Torque
Tension pulley bolts: 25 N
.m (2.5 kg-m, 18.5 lb-ft)

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-9
IDLE UP SYSTEM
IDLE UP SYSTEM CHECK
1) Warm up engine to normal operating temperature.
2) Turn A / C switch OFF, if equipped.
3) Turn steering wheel fully and check idle speed.
Engine idle speed drops a little momentarily when steering
wheel is turned fully but returns to its specified level immediately.
If power steering pressure switch connector is connected, check
the same with that connector disconnected. Momentary drop of
engine idle speed should be less when it is connected than when
disconnected.
FLUID
FLUID LEAKAGE CHECK
Start engine and turn steering wheel fully to the right and left so that maximum hydraulic pressure is provided. Then
visually check gear box, P / S pump and P / S fluid reservoir themselves and each joint of their connecting pipes for
leakage.
CAUTION:
Never keep steering wheel turned fully for longer than 10 seconds.

YH4
GRAND
VITARA
1. P / S fluid reservoir
2. Attachment
3. Gasket4. Union bolt
5. High pressure side
6. Low pressure side
1. P / S fluid reservoir
2. Gauge valve (open)
3. P / S pump4. P / S gear box
5. High pressure side
6. Low pressure side
3B1-10 POWER STEERING (P / S) SYSTEM
HYDRAULIC PRESSURE IN P / S CIRCUIT
HYDRAULIC PRESSURE CHECK
1) After cleaning joint of high pressure hose and P / S pump thor-
oughly, disconnect hose from pump and install special tool (oil
pressure gauge, attachment and hose).
Tighten each flare nut to specified torque.
CAUTION:
Take care not to cause damage to A / C condenser during
service operation, if equipped.
Special Tool
(A): 09915-77410 (Oil pressure gauge)
(B): 09915-77420
2) Check each connection for fluid leakage and bleed air.
Refer to ªAIR BLEEDING PROCEDUREº in this section.
3) With engine idling, turn steering wheel and warm up engine till
temperature of fluid in P/S fluid reservoir rises to 50 ± 60
C (122
± 140
F).
4) Check back pressure by measuring hydraulic pressure with en-
gine idling and hands off steering wheel.
Back pressure: Lower than 1000 kPa (10 kg / cm
2, 142 psi)
When back pressure is higher than specified values, check con-
trol valve and piping for clogging.

YH4
GRAND
VITARA
1. P / S fluid reservoir
2. Gauge valve (shut)
3. Oil pressure gauge
4. P / S pump
5. P / S gear box
1. P / S fluid reservoir
2. Gauge valve (open)
3. Oil pressure gauge
4. P / S pump
5. P / S gear box
POWER STEERING (P / S) SYSTEM 3B1-11
5) Check relief pressure

Increase engine speed to about 1,500 r / min (rpm). Close
gauge valve gradually while watching pressure increase indi-
cated by gauge and take reading of relief pressure (maximum
hydraulic pressure).
Relief pressure:
6200 ± 7000 kPa
(62 ± 70 kg / cm
2, 882 ± 995 psi) G16 Type engine. . . . . . .
6700 ± 7500 kPa
(67 ± 75 kg / cm
2, 953 ± 1067 psi) J20 Type engine. . . . . . .
7050 ± 7850 kPa
(70.5 ± 78.5 kg / cm
2, 1003 ± 1116 psi) H25 Type engine. .

When it is higher than specified values, possible cause is mal-
function of relief valve.

When it is lower than specified values, possible cause is either
failure of P / S pump or settling of relief valve spring.
CAUTION:
Be sure not to close gauge valve for longer than 10 se-
conds.

Next, open gauge valve fully and increase engine speed to
about 1,500 r / min (rpm). Then turn steering wheel to the left
or right fully and take reading of relief pressure.
Relief pressure:
6200 ± 7000 kPa
(62 ± 70 kg / cm
2, 882 ± 995 psi) G16 Type engine. . . . . . .
6700 ± 7500 kPa
(67 ± 75 kg / cm
2, 953 ± 1067 psi) J20 Type engine. . . . . . .
7050 ± 7850 kPa
(70.5 ± 78.5 kg / cm
2, 1003 ± 1116 psi) H25 Type engine. .

When it is higher than specified values, possible cause is mal-
function of relief valve.

When it is lower than specified values, possible cause is failure
in steering gear box. Replace gear box.
CAUTION:
Be sure not to hold steering wheel at fully turned posi-
tion for longer than 10 seconds.
BOOT
STEERING RACK BOOT CHECK
Check boot for crack and damage which, if any, means possibility
of rusty gear, entry of dust or lack of grease. Also, check if any of
such faulty conditions exists.
Check steering rack boot for dent or breakage.
If there is a dent, keep boot in most compressed state for some se-
conds to correct dent.

YH4
GRAND
VITARA
3B1-12 POWER STEERING (P / S) SYSTEM
TIE-ROD END BOOT CHECK
Check boot for crack and damage and if any, replace it with a new
one.
AIR BLEEDING PROCEDURE
1) Hoist the front end of vehicle and apply safety stands.
2) Fill P / S fluid reservoir with fluid up to specified level.
NOTE:
Before starting engine, place transmission gear shift lever
in ªNeutralº (shift selector lever to ªPº range for A / T mod-
el), and set parking brake.
3) After running engine at idling speed for 3 to 5 seconds, stop it
and add fluid to satisfy specification.
4) With engine stopped, turn steering wheel to the right and left as
far as it stops, repeat it a few times and fill fluid to specified level.
5) With engine running at idling speed, repeat stop-to-stop turn of
steering wheel till all foams in P / S fluid reservoir are gone.
NOTE:
Make sure to bleed air completely. If air remains in fluid, P / S
pump may make humming noise or steering wheel may feel
heavy.
6) Finally check to make sure that fluid is filled to specified level.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-19
Tightening Torque
(a): 60 N.m (6.0 kg-m, 43.5 lb-ft)
(b): 25 N.m (2.5 kg-m, 18.5 lb-ft)
(c): 55 N.m (5.5 kg-m, 40.0 lb-ft)
(d): 11 N.m (1.1 kg-m, 8.0 lb-ft)
(e): 35 N.m (3.5 kg-m, 25.5 lb-ft)
( f ): 40 N.m (4.0 kg-m, 29.0 lb-ft)
(g): 45 N.m (4.5 kg-m, 33.0 lb-ft)
1. Power steering pump assembly
2. Bracket
3. P / S fluid reservoir4. High pressure hose & pipe
5. Suction hose
6. Low pressure return hose7. Oil tank bracket
8. To P / S gear box
[G16 ENGINE MODEL]
[J20 ENGINE MODEL][H25 ENGINE MODEL]
POWER STEERING PUMP

YH4
GRAND
VITARA
3B1-20 POWER STEERING (P / S) SYSTEM
1. P/S fluid
reservoir
2. Suction hose
1. P / S pulley
2. Mounting bolt
9. Vane
10. Rotor
11. Snap ring
12. Side plate
13. Pulley (pump shaft)
14. Oil seal
15. Pump body
16. Flow control
valve Assembly 1. Suction connector
2. O-ring
3. Pressure switch
4. Flow control valve
(Relief valve)
5. Spring
6. Plug
7. Pump cover
8. Cam ring
REMOVAL
NOTE:
Be sure to clean each joint of suction and discharge sides
thoroughly before removal.
1) Remove suction hose from pump, then disconnect battery nega-
tive cable.
2) Remove P / S fluid reservoir with suction hose.
3) Remove union bolt. Then disconnect high pressure pipe from
pump.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to pipe.
4) Disconnect pressure switch lead wire at switch terminal.
5) Loosen related bolts and remove power steering drive belt.
6) Remove P / S pump mounting bolt (s).
7) Remove P / S pump.
NOTE:
Plug each port of removed pump to prevent dust or any oth-
er foreign matter from entering.
DISASSEMBLY
1) Clean its exterior thoroughly.
2) With aluminum plates placed on vise first, grip pump body with
it.
3) Remove suction connector bolt, suction connector and O-ring
from pump body.
4) Remove power steering pressure switch (terminal set) from
pump body.
5) Remove plug, flow control spring and relief valve (flow control
valve) from pump body.
6) Remove cover bolts, pump cover and O-ring from pump body.
7) Remove snap ring from pump shaft.
8) Remove vanes from rotor.
9) Remove cam ring, rotor, side plate and O-rings from pump
body.
10) Pull out pulley from pump body.
11) Remove oil seal from pump body.

YH4
GRAND
VITARA
POWER STEERING (P / S) SYSTEM 3B1-21
1. Thickness gauge
INSPECTION
Pump Body, Cover, Side Plate and Shaft
Check sliding surfaces of each part for wear and damage.
If any defect is found, replace pump assembly.
Cam Ring
Check vane sliding surface of cam ring for wear and damage.
If any defect is found, replace pump assembly.
Rotor and Vane

Check sliding surfaces of rotor and vane for wear and damage.

Check clearance between rotor and vane.
Clearance: Standard 0.015 mm (0.0006 in.)
Limit 0.027 mm (0.0011 in.)
Replace pump assembly if any defect is found in above checks.
Relief Valve (Flow Control Valve) and Its Spring

Check fluid passage of relief valve and orifice of connector for ob-
struction (clogged).

Check sliding surface of relief valve for wear and damage.