2000 SUZUKI GRAND VITARA lspv

YH4
GRAND
VITARA
BRAKES 5-17
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe 2-way (or 4-way) joint bolt232.317.0
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV7.50.755.5
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
Stop light switch lock nut7.50.755.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.

YH4
GRAND
VITARA
5A
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-1
SECTION 5A
BRAKES PIPE/HOSE/MASTER CYLINDER
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to assure
proper retention of all parts. There is to be no welding as it may result in extensive damage and weakening
of the metal.
CONTENTS
GENERAL DESCRIPTION5A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder Assembly5A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Booster Assembly5A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LSPV (Load Sensing Proportioning Valve) Assembly 5A- 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS5A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE5A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Brake Hose / Pipe5A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Brake Hose / Pipe5A- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder Reservoir5A- 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder Assembly5A-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Booster5A-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LSPV (Load Sensing Proportioning Valve) Assembly 5A-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS5A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL5A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
1. LSPV
2. LSPV lever
3. Spring
4. LSPV stay
5. Brake flare nut
[A]: Type A
[B]: Type B
1. Plunger
2. Lip seal
3. LSPV lever
4. Sensor spring
5. From master cylinder
primary chamber
(Rear wheel brake)
6. From master cylinder
secondary chamber
(Front wheel brake)
7. To rear wheel brake
8. Pin
9. Bolt hole
[A] [B]
44
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-3
LSPV (Load Sensing Proportioning Valve) ASSEMBLY (if equipped)
As shown in figure below, LSPV is included within the brake circuit which connects the master cylinder and the rear
wheel brake. It controls the hydraulic pressure applied to the rear wheel brake according to the loaded state of the
vehicle (or weight of the load), whereby preventing the rear wheels from getting locked prematurely.
Also, it releases the above described control over the hydraulic pressure applied to the rear wheel brake, should
any failure occur in the hydraulic circuit of the front wheel brake so that the hydraulic pressure produced in the mas-
ter cylinder is applied to the rear wheel brake directly to operate it.
CONSTITUTION
The LSPV components are grouped into three sections as follows.
ªAº: Sensor section
The main parts in this section are a lever and a spring which senses variation in the vehicle height as affected
by the loaded condition and converts it into the load.
ªBº: Hydraulic pressure control section
Included in this section are a stepped plunger and valve mechanism to execute proportional control.
ªCº: Fail-safe section
The main parts in this section are a chamber which draws in the hydraulic pressure from the front wheel brake
system and a fail-safe piston which releases the valve mechanism in the control section connected to the rear
wheel brake, should any failure occur in the front wheel brake system.

YH4
GRAND
VITARA
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-7
1. Rear axle
2. Shock absorber
3. Clamp
1. Brake pipe (to rear)
2. Brake pipe
(to LSPV, for vehicle without ABS)
3. 4-way (2-way) joint
4. Chassis frame
REAR BRAKE HOSE / PIPE
REMOVAL
1) Raise and suitably support vehicle. Remove tire and wheel.
2) Clean dirt and foreign material from both hose end or pipe end fittings. Remove brake hose or pipe.
INSTALLATION
1) Reverse removal procedure for brake hose or pipe installation procedure.

Be sure to obtain more than 3 mm (0.118 in.) clearance between axle housing and brake pipe.

Install clamps properly referring to figure below and tighten bolts.

When installing hose, make sure that it has no twist or kink.
2) Fill and maintain brake fluid level in reservoir. Bleed brake system.
3) Perform brake test and check each installed part for fluid leakage.

YH4
GRAND
VITARA
1. LSPV
2. Brake pipe
1. LSPV assembly
2. LSPV spring
3. LSPV stay
4. Bolt
5. Stepper bole
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-17
LSPV (Load Sensing Proportioning Valve)
ASSEMBLY (if equipped)
REMOVAL
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Hoist vehicle.
3) Disconnect brake pipes from LSPV.
4) Remove LSPV assembly with spring from vehicle body.
5) Remove spring from lever.
CAUTION:

LSPV assembly must not be disassembled.
Replace with new one if defective.

Stopper bolt should not be loosened or tightened. (if
equipped)
INSTALLATION
CAUTION:
Refer to above CAUTION.
Install by reversing removal procedure, noting the following.
1) Apply multi-purpose grease ªAº to upper and lower joint of coil
spring.

YH4
GRAND
VITARA
5A-18 BRAKES PIPE / HOSE / MASTER CYLINDER
1. LSPV spring bolt
2. LSPV bolt
3. Brake pipe flare nut
4. Air bleeding plug
1. LSPV lever
2. Stopper bolt (if equipped)
3. Coil spring ªAº: Don't turn(a)
2) Torque each bolt and nut to specification as indicated respec-
tively in figure.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft) (brake flare nut)
(c): 7.5 N
.m (0.75 kg-m, 9.0 lb-ft) (bleeder plug)
3) Upon completion of installation, fill reservoir tank with specified
fluid and bleed air from brake system.
NOTE:
Make sure to bleed air from LSPV bleeder without failure.
4) After bleeding air, check that LSPV is installed properly, referring
to following INSPECTION & ADJUSTMENT.
INSPECTION & ADJUSTMENT
Confirm the following before inspection and adjustment.

Fuel tank is filled with fuel fully.

Vehicle is equipped with spare tire, tools, jack and jack handle.

Vehicle is free from any other load.
With vehicle in above conditions;
1) Place it on level floor.
2) Push up (for 5 door model) or push down (for 3 door model)
LSPV lever with finger till it stops and measure length ªLº of coil
spring as it is pulled.
3) Spring length ªLº should be the value specified below.
Spring length (between spring end and spring bolt)
ªLº: 103 mm (4.06 in.) (5 door model). . . . .
ªLº: 157 mm (6.18 in.) (3 door model). . . . .
4) If it isn't, adjust it to specification by changing stay positions as
shown in figure. After adjustment, tighten bolt to specified
torque.
For details, refer to left figure.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
NOTE:
Check to make sure that LSPV body and brake pipe joints
are free from fluid leakage. Replace defective parts, if any.

YH4
GRAND
VITARA
BRAKES PIPE / HOSE / MASTER CYLINDER 5A-19
09922-85811
Connector pin remover09950-96010
Booster piston rod gauge09952-16010
Booster piston rod adjuster
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake flexible hose bolt (Brake caliper / 2 (4) way joint)232.317.0
Master cylinder attaching nut131.39.5
Booster nut131.39.5
Clevis nut252.518
2-way (or 4-way) joint mounting bolt101.07.5
Brake pipe flare nut161.611.5
Front caliperM88.00.86.0
Brake bleederplug
Front cali erM108.50.856.5Brake bleeder lugWheel cylinder7.50.755.5
LSPV8.00.86.0
LSPV mounting bolt
LSPV stay bolt232.317.0
LSPV spring nut
Wheel nut10010.072.5
REQUIRED SERVICE MATERIAL
MATERIALSRECOMMENDED
SUZUKI PRODUCTUSE
Brake fluid
Indicated on reservoir
cap or described in owner's
manual of vehicle
To fill master cylinder reservoir.

To clean and apply to inner parts of master
cylinder caliper and wheel cylinder when
they are disassembled.
SPECIAL TOOLS