2000 SUZUKI GRAND VITARA Windows

YH4
GRAND
VITARA
8D-6 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED)
TroublePossible causeCorrection
All power doors are not
locked / unlocked by both
driver side door key
switch and power door
lock switch
ªDOOR LOCKº fuse blown (Hard Top
Model)
ªD / Lº fuse blown (Canvas Top Model)

Power door controller faulty

Wiring or grounding faultyReplace fuse to check for short
Replace controller
Repair
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-7
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
TroublePossible causeCorrection

All power doors are not
locked / unlocked by
both driver side door key
switch and power door
lock switch. But all
power doors are locked /
unlocked by keyless
entry transmitter

All power doors are not
locked / unlocked by
driver side door key
switch, power door lock
switch and keyless entry
transmitter

When power doors are
locked / unlocked by
keyless entry
transmitter, hazard
warning lights do not
flash
ªDOOR LOCKº fuse blown

Power door lock and keyless entry system
faultyReplace fuse to check for short
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
keyless entry transmitter
Code registration error

Transmitter battery dead

Transmitter faulty

Power door lock and keyless entry system
faultyRegister code
Replace battery
Replace transmitter
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
Although any door is
opened within 30 seconds
after power door(s)
unlocked by keyless entry
transmitter, all power
doors are locked again
automatically
Door switch faulty

Wiring harness connected to door switch
brakesReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator
Operation distance of
keyless entry is unstable
Transmitter battery dead

Transmitter faultyReplace battery
Replace transmitter

YH4
GRAND
VITARA
8D-8 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR MIRROR CONTROL SYSTEM
TroublePossible causeCorrection
All power mirrors do not
operate
ªCIGARº fuse blown (Hard Top Model)
ªCIGº fuse blown (Canvas Top Model)

Power door mirror switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
One power mirror does
not operate
Power door mirror switch faulty

Actuator (power door mirror motor) faulty

Wiring or grounding faultyReplace switch
Replace actuator
Repair
DOOR MIRROR HEATER (IF EQUIPPED)
TroublePossible causeCorrection
The surface of mirror is
not defrosted although
door mirror heater
switch is ON
ªREAR DEFGº fuse blown (Hard Top Model)
ªDEFº fuse blown (Canvas Top Model)

Door mirror heater switch faulty

Door mirror heater faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Replace outside mirror
Repair
POWER SLIDING ROOF (IF EQUIPPED)
TroublePossible causeCorrection
Sliding roof does not
operate (sliding roof
motor runs OK)
Foreign object stuck in sliding roof rail

Misinstallation of sliding roof rail

Conflicts of sliding roof parts

Misinstallation of sliding roof drive cableRemove or clean stuck object
Install correctly
Fix conflicts
Install correctly
Sliding roof does not
operate (sliding roof
motor does not run)
ªSUN ROOFº fuse blown

Sliding roof switch faulty

Sliding roof motor ass'y faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Replace motor
Repair
FRONT SEAT HEATER (IF EQUIPPED)
TroublePossible causeCorrection
Both seat back and
cushion do not become
hot although seat heater
switch is LO / HI position
ªSEAT HTRº fuse blown (Hard Top Model)
ªS / Hº fuse blown (Canvas Top Model)

Seat heater switch faulty

Seat heater circuit in seat back and / or seat
cushion faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Replace heater front back and /
or heater front cushion
Repair
Only seat back does not
become hot although seat
heater switch is HI
position
Seat heater circuit in seat back faulty
(Hard Top Model)

Seat heater circuit in seat back and / or seat
cushion faulty (Canvas Top Model)

Seat heater switch faulty

Wiring faultyReplace heater front back
Replace heater front back
and / or heater front cushion
Replace switch
Repair
Only seat cushion does
not become hot although
seat heater switch is HI
position
Seat heater circuit in seat back and / or seat
cushion faulty (Hard Top Model)

Seat heater circuit in seat cushion
(Canvas Top Model)

Seat heater switch faulty

Wiring faultyReplace heater front back
and / or heater front cushion
Replace heater front cushion
Replace switch
Repair

YH4
GRAND
VITARA
WASHER
ONINT
LO
HI
Type A
Type B
Type C
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-9
Wiper
SW
Terminal
Wiper SW
Terminal
ON-VEHICLE SERVICE
WINDSHIELD WIPER AND WASHER
FRONT WIPER AND WASHER
INSPECTION
Front Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
B3+2+1AsB3+2+1As
OFFB3WINTB3W
LOOFF
HION
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
Wiper Motor
1) As illustrated, use a 12 V battery to connect its (+) terminal to ter-
minal ªAº, and its (±) terminal to Black lead wire (2) (Type A, B)
or terminal ªEº (Type C).
If motor (1) rotates at a low revolution speed of 45 to 55 rpm, it
is proper. For high speed check, connect battery (+) terminal to
terminal ªBº, and its (±) terminal to Black lead wire (2) (Type A,
B) or terminal ªEº (Type C). If motor rotates at a high revolution
speed of 67 to 83 rpm, it is proper.

YH4
GRAND
VITARA
Type B Type A
Type C
1. Washer tank
8D-10 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) Testing automatic stop action.
a) Connect 12 V battery (+) terminal to terminal ªAº of wiper mo-
tor (1) and (±) terminal to Black lead wire (2) (Type A, B) or
terminal ªEº (Type C), and let the motor turn.
b) Disconnect terminal ªAº from battery, and let the motor stop.
c) Connect terminal ªAº and ªDº with a jumper wire (3), and con-
nect terminal ªCº to battery (+) terminal. Observe the motor
turns once again then stops at a given position.
d) Repeat a) thru c) several times and inspect if the motor stops
at the given position every time.
Washer Pump
Connect battery (+) and (±) terminals to pump (+) and (±) terminals
respectively to check pumping rate.
Check for both front (3) and rear (2) (if equipped) washer pump.
Pumping Rate:
Front and Rear (if equipped) more than 1.0 l / min.
(2.1 US pt. / min.,
1.76 lmp pt. / min.).

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-11
SLOW
FAST
10 ± 14 V
0 V
1.6
1 sec.
10 ± 14 V
0 V
10.7
5 sec.
Intermittent Wiper Relay Circuit
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Turn the front wiper switch to INT position.
4) Turn the intermittent time control switch to FAST position.
5) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
6) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
Check that the voltmeter indicates the battery voltage (10 ±
14 V).
7) Connect terminal ªAsº and terminal ªB3º by a jumper wire. Then
move jumper wire end connected to terminal ªB3º to terminal ªEº.
Observe the voltmeter voltage drops to 0 V right after connecting
the jumper wire from terminal ªB3º to ªEº. Then the voltage rises
to battery voltage (10 ± 14 V) within the time shown in the table
below.
INT time control
switch position
Voltage
FAST
SLOW

YH4
GRAND
VITARA
WASHER
ONON
OFF
10 ± 14V
0VApprox. 2.5 sec.
Approx. 0.5 sec.
8D-12 WINDOWS, MIRRORS, SECURITY AND LOCKS
Washer Linked Operation
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Make sure that front wiper switch is at OFF position.
4) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
5) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
6) Pull washer switch and check that voltage changes as shown in
the table.
Washer switch
Voltmeter

YH4
GRAND
VITARA
Terminal
Switch
Terminal
Switch
ON
INT
WASHER
ON
BRINT
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-13
REAR WIPER AND WASHER (IF EQUIPPED)
INSPECTION
Rear Wiper and Washer Switch (in Combination Switch)
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
as shown below. If check result is not as specified, replace
switch.
Rear Wiper Switch
BRINT+IRBRINT+IR
OFF
INT
ON
Rear Washer Switch
BRWRBRWR
OFF
ON
Washer Pump
Refer to FRONT WIPER AND WASHER INSPECTION in this sec-
tion.
Wiper Motor
1) TESTING WIPER MOTOR
As shown left, use a 12 V battery to connect its (+) and (±) termi-
nals to terminal ªDº and Black lead wire (2) respectively. Then
motor (1) should rotate at 35 to 45 rpm.