2000 SUZUKI GRAND VITARA Crankshaft

YH4
GRAND
VITARA
[D] [C] [A]
1. P / S pump pulley
2. A / C compressor
pulley (if equipped)
3. Crankshaft pulley
4. Tension pulley
5. Tension pulley bolts[A]: G16 type engine with A / C
[B]: G16 type engine without A / C
[C]: H25 type engine with A / C
[D]: H25 type engine without A / C
[B]
3B1-8 POWER STEERING (P / S) SYSTEM
POWER STEERING PUMP DRIVE BELT
NOTE:
For J20 Type engine, refer to Section 6H ªGENERATOR BELTº.
INSPECTION
Check that belt is free from any damage and properly fitted in pulley
groove.
BELT TENSION CHECK
Check belt tension by measuring how much it deflects when
pushed at intermediate point between pulleys with about 10 kg
(22 lb) force.
Deflection of P / S belt:
6 ± 9 mm (0.24 ± 0.35 in.) G16 Type engine. . . . . . . . . . . . . . . . .
4 ± 7 mm (0.16 ± 0.28 in.) H25 Type engine. . . . . . . . . . . . . . . . .
BELT TENSION ADJUSTMENT
[For G16 Type engine]
a) To adjust P / S pump drive belt tension, use adjusting bolt of com-
pressor for A / C equipped vehicles and that of P / S pump for ve-
hicles without A / C.
b) Adjust belt tension to above specification.
c) Then tighten adjusting and mounting bolts to specified torque.
[For J20 Type engine]
To adjust P / S pump drive belt tension, refer to ªGENERATOR
BELTº in Section 6H.
[For H25 Type engine]
a) To adjust P / S pump drive belt tension, loosen tension pulley
bolts and turn tension pulley using hexagon wrench.
b) Adjust belt tension to above specification.
Then tighten tension pulley bolts to specified torque.
Tightening Torque
Tension pulley bolts: 25 N
.m (2.5 kg-m, 18.5 lb-ft)

YH4
GRAND
VITARA
1. Crankshaft
2. Flywheel
3. Clutch disc
4. Pressure plate
5. Clutch cover
6. Diaphragm spring
7. Release bearing
8. Input shaft bearing
9. Input shaft
10. Operating cylinder
11. Clutch housing
12. Release fork
7C1-2 CLUTCH
The clutch is a diaphragm-spring clutch of a dry single
disc type. The diaphragm spring is of a tapering-finger
type, which is a solid ring in the outer diameter part,
with a series of tapered fingers pointing inward.
The disc, carrying torsional coil springs, is positioned
on the transmission input shaft with an involute spline
fit.
The clutch cover is secured to the flywheel, and car-
ries the diaphragm spring in such a way that the pe-
ripheral edge part of the spring pushes on the pres-
sure plate against the flywheel (with the disc in be-
tween), when the clutch release bearing is held back.
This is the engaged condition of the clutch.Depressing the clutch pedal causes the release bear-
ing to advance and pushes on the tips of the tapered
fingers of the diaphragm spring. When this happens,
the diaphragm spring pulls the pressure plate away
from the flywheel, thereby interrupting the flow of
drive from flywheel through clutch disc to transmis-
sion input shaft.
GENERAL DESCRIPTION

YH4
GRAND
VITARA
7C1-12 CLUTCH
(C)
1
ªAº, (a)1
2
1. Flywheel
2. Bolt
1. Clutch cover
INSTALLATION
NOTE:
Before assembling, make sure that flywheel surface and pres-
sure plate surface have been cleaned and dried thoroughly.
1) Install flywheel to crankshaft and tighten bolts to which sealant
is applied to specification.
Special Tool
(A): 09924-17810
ªAº: Sealant 99000-31110
Tightening Torque
(a): 78 N
.m (7.8 kg-m, 56.5 lb-ft) (G16 engine)
(a): 70 N
.m (7.0 kg-m, 50.5 lb-ft) (J20 and H25 engines)
2) Using special tool (B), install input shaft bearing to flywheel.
Special Tool
(B): 09925-98210
3) Aligning clutch disc to flywheel center by using special tool (C),
install clutch cover and bolts. Then tighten bolts to specification.
NOTE:

While tightening clutch cover bolts, compress clutch disc
with special tool (C) by hand so that disc centered.

Tighten cover bolts little by little evenly in diagonal order.
Special Tools
(A): 09924-17810
(C): 09923-36330 (G16 engine)
(C): 09923-36320 (J20 and H25 engines)
Tightening Torque
(b): 23 N
.m (2.3 kg-m, 16.5 lb-ft)

YH4
GRAND
VITARA
CLUTCH 7C1-13
1. Release fork
2. Clip
3. Input shaftªBº
ªBº
ªAº 3
2
1
1
2
4) Install clip to release fork and apply grease.
ªAº: Grease 99000-25010
Then install release fork and release bearing as shown in figure.
5) Slightly apply grease to input shaft and install clutch disc. Then
join transmission transfer assembly with engine. Refer to SEC-
TION 7A.
ªBº: Grease 99000-25210
NOTE:
Turn crankshaft with wrench from front while inserting
transmission input shaft to clutch disc until splines mesh.