Page 380 of 413
Maintenance and service11-41
–
CONTINUED –
HS0191
Metal support
4. If the new b lad e rub b er is not p rovid ed with two metal sp ines, remove
the metal sp ines from the old b lad e rub b er and inst all them in the new
b lad e rub b er.
HS0192
Metal spines
5. Alig n the c laws of the metal sup p ort with the g ro oves in the rub b er
and slid e the b lad e rub b er assemb ly into the metal sup p ort until it loc ks.
Be sure to p osition the c laws at the end of the met al sup p ort b etween the
stop p ers on the rub b er as shown. If the rub b er is n ot retained p rop erly,
the wip er b lad e may sc ratc h the wind shield .
Page 382 of 413
Maintenance and service11-43
–
CONTINUED –
and other metal jewelry. Never allow metal tools to contact the
positive battery terminal and anything connected to it WHILE youare at the same time in contact with any other metallic portion ofthe vehicle because a short circuit will result.
Keep everyone including children away from the battery.
Charge the battery in a well-ventilated area.
CAUTION
Never use more than 10 amperes when charging the battery be-
cause it will shorten battery life.
It is unnec essary to p eriod ic ally c hec k the b attery fluid level or p eriod i-
c ally refill with d istilled water. Fuses
CAUTION
Never replace a fuse with one having a higher rating or with mate-
rial other than a fuse because serious damage or a fire could re-sult.
HBB008CBHB8003CA
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in
Page 384 of 413

Maintenance and service11-45
–
CONTINUED –
4. Pull out the fuse with the fuse p uller.
5. Insp ec t the fuse. If it has b lown, rep lac e it wit
h a sp are fuse of the
same rating .
6. If the same fuse b lows ag ain, this ind ic ates that its system has a
p rob lem. Contac t your SUBARU d ealer for rep airs.
Main fuse and fusible link
HB8003CB
The main fuses and fusib le link are d esig ned to mel t d uring an overload
to p revent d amag e to the wiring harness and elec tri c al eq uip ment.
Chec k the main fuses and fusib le link if any elec tr ic al c omp onent fails to
op erate (exc ep t the starter motor) and other fuses are g ood . A melted
main fuse or fusib le link must b e rep lac ed . Use onl y rep lac ements with
the same sp ec ified rating as the melted main fuse o r fusib le link. If a
main fuse or fusib le link b lows after it is rep lac e d , have the elec tric al sys-
tem c hec ked b y your nearest SUBARU d ealer.
Installation of accessories
Always c onsult your SUBARU d ealer b efore installing fog lig hts or any
other elec tric al eq uip ment in your vehic le. Suc h ac c essories may c ause
the elec tronic system to malfunc tion if they are in c orrec tly installed or if
they are not suited for the vehic le.
Page 386 of 413
Maintenance and service11-47
–
CONTINUED –
Wattag e Bulb No.
8 Bac kup lig ht
Sed an 12V –27W 3156K
Station wag on 12V –27W 1156
9 Lug g ag e area lig ht 12V –13W —
Q Hig h mount stop lig ht
Sed an 12V –18W 921
Station wag on 12V –13W 912
W Rear turn sig nal lig ht
Sed an 12V –21W —
Station wag on 12V –21W R2172 7440
E Brake/tail lig ht
Sed an 12V –27/8W 3157K
Station wag on 12V –27/8W 1157
R Lic enc e p late lig ht
Sed an 12V –5W 168
Station wag on 12V –3.8W or 5W 194 or 168
T Trunk room lig ht 12V –5W W5W
HBF013FC
HBB033BC
Page 388 of 413
Maintenance and service11-49
–
CONTINUED –
n
Low beam light bulbs
HBB042BA
HBB041BB
1. Disc onnec t the elec tric al c onnec tor for the b lac k c ab le.
2. Remove the retainer sp ring .
3. Rep lac e the b ulb , then set the retainer sp ring se c urely.
4. Rec onnec t the elec tric al c onnec tor for b lac k c ab l e.
5. Install the head lig ht b ulb c over. n High beam light bulbs
HBB044BB
HBB043BA
1. Disc onnec t the elec tric al c onnec tor from the b ulb .
2. Remove the b ulb from the head lig ht assemb ly b y tu rning it c oun-
terc loc kwise.
3. Rep lac e the b ulb with new one.
4. Rec onnec t the elec tric al c onnec tor. At this time, use c are not to
touc h the b ulb surfac e.
Page 390 of 413
Maintenance and service11-51
–
CONTINUED –
mad e at a SUBARU d ealer.
HBB016BA
1. Remove the head lig ht assemb ly mounting sc rews loc
ated at the top
of and the front of the head lig ht assemb ly using a p hillip s sc rewd river or
an op en-end wrenc h.
2. Move the head lig ht assemb ly forward .
HBB039CBHBB020BA
3. Remove the b ulb soc ket from the head lig ht assemb l y b y turning it
c ounterc loc kwise.
4. Remove the b ulb from the soc ket b y p ushing it and turning c ounter-
c loc kwise. Install a new b ulb in the soc ket.
5. Set the b ulb soc ket into the head lig ht assemb ly a nd turn it c loc kwise
until it loc ks.
6. Set the head lig ht assemb ly into the vehic le b od y. Tig hten the mount-
ing sc rews.
Page 392 of 413
Maintenance and service11-53
–
CONTINUED –
5. Install a new b ulb in the soc ket.
6. Set the b ulb soc ket into the rear c omb ination lig
ht assemb ly and
turn it c loc kwise until it loc ks.
7. Close the c over and latc h the c loc k. Station wagon
n Brake/tail and rear turn signal light bulbs
It may b e d iffic ult to rep lac e the b ulb s. It is rec ommend ed that you
have the b ulb s rep lac ed b y your SUBARU d ealer.
HBB022BB
HBB021BB
1. Remove the lig ht b ulb rep lac ement servic e hole c overs at two
p lac es b y p rying the ed g e of the c over with a reg ul ar sc rewd river.
2. Remove the up p er and lower nuts. Then, slid e the rear c omb ina-
tion lamp assemb ly to the rear and remove it from t he vehic le.
HBB047BBHBB024BB
Brake/tail light bulbRear turn signal light bulb
Page 394 of 413
Maintenance and service11-55
–
CONTINUED –
n
Back-up and brake/tail light bulbs
HBB025BA
HBB026BC
1. Unlatc h the rear c omb ination lig ht c over b y movin g the knob up -
ward . Op en the c over up .
2. Remove the b ulb soc ket from the rear c omb ination lig ht assemb ly
b y turning it c ounterc loc kwise.
3. Remove the b ulb from the soc ket b y p ushing it and turning c oun-
terc loc kwise. Install a new b ulb in the soc ket.
4. Set the b ulb hold er into the rear c omb ination lig ht assemb ly and
turn it c loc kwise until it loc ks.
5. Close the c over and latc h the loc k.
License plate light
HBB027BA
HBF013EA
1. Remove the mounting sc rews using a p hillip s sc rew d river.