2000 SUBARU LEGACY Manu at

5-38
: Ind ic ates that the top sid e of the c assette is b eing p layed b ac k.
: Ind ic ates that the b ottom sid e of the c assette i s b eing p layed
b ac k. Program switching buttons
When the p rog ram switc hing b uttons “
” and “” 9 , are
p ressed at the same time d uring p layb ac k, the tap e travel ind ic ators
will switc h and the p layer will b eg in p laying b ac k the op p osite sid e of
the tap e. The same mec hanism is automatic ally ac tiv ated when the
end of the tap e is reac hed . This allows the op p osit e sid e of the tap e
to p lay, p rovid ing c ontinuous p layb ac k. Fast-forward button
To fast-forward the tap e, p ress the “
” or “” b utton 9 in the
same d irec tion as the tap e travel ind ic ator. To sto p fast-forward ing ,
lig htly p ress the op p osite sid e of the “
” or “” b utton.
Rewind button
To rewind the tap e, p ress the “
” or “” b utton 9 in the d irec -
tion op p osite to the tap e travel ind ic ator. To stop rewind ing , lig htly
p ress the op p osite sid e of the “
” or “” b utton.
Eject button (
)
When the “
” b utton 7 is p ressed , p layb ac k stop s and the c assette
tap e is ejec ted .
Before the ig nition switc h is turned to the “OFF ” p osition, ejec t the
tap e from the p layer. Always make c ertain that you remove the c as-
sette tap e. Dolby BNR button (BNR)
Press “BNR ” b utton
Q when p laying tap es rec ord ed using the Dolb y
NR system*. The “BNR ” ind ic ator will lig ht up and hig h-freq uenc y
noise on the tap e will b e red uc ed for c learer sound rep rod uc tion.
* Noise red uc tion system manufac tured und er lic ense from Dolb y Lab oratories
Lic ensing Corp oration. “Dolb y ” and the d oub le-D Symb ol are trad e marks of
Dolb y Lab oratories Lic ensing Corp oration.

7
Starting and operating Fuel7-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel requirements 7-2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel filler lid and cap 7-4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
State emission testing (U.S. only) 7-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparing to drive 7-7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the engine 7-8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the engine for a manual transmission vehicle 7-8 . . . . . . . . . .
Starting the engine for an automatic transmission vehicle 7-9 . . . . . .
Starting the engine during cold weather below –4F ( –20 C) 7-10 . . .
Starting a flooded engine 7-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stopping the engine 7-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual transmission 7-11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 7-14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selector lever for automatic transmission 7-15 . . . . . . . . . . . . . . . . . . . . . . . . . .
Shift lock release 7-19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear viscous limited slip differential (LSD) (GT, GT-LTD, OUTBACK-CW and OUTBACK-LTD) 7-20 . . . . . . . . . .
Power steering 7-20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Braking 7-21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Braking tips 7-21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system 7-21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disc brake pad wear warning indicators 7-22 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS (Anti-lock Brake System) 7-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking your vehicle 7-25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control (if equipped) 7-27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starting and operating7-3
–
CONTINUED –

Gasoline for cleaner air CAUTION
Do not let fuel spill on the exterior surfaces of the vehicle. Fuels containing alcohol may cause paint damage, which is not cov-
ered under the SUBARU Limited Warranty.
Your use of g asoline with d eterg ent ad d itives will help p revent d ep os-
its from forming in your eng ine and fuel system. Th is help s keep your
eng ine in tune and your emission c ontrol system wor king p rop erly,
and is a way of d oing your p art for c leaner air. If you c ontinuously use
a hig h q uality fuel with the p rop er d eterg ent and o ther ad d itives, you
should never need to ad d any fuel system c leaning a g ents to your
fuel tank.
Many g asolines are now b lend ed with materials c alle d oxyg enates.
Use of these fuels c an also help keep the air c lean er. SUBARU ap -
p roves the use of oxyg enated b lend fuels, suc h as M TBE (Methyl Ter-
tiary Butyl Ether) or ethanol (ethyl or g rain alc oh ol). The b lend ed fuels
should c ontain no more than 15% MTBE or 10% ethanol for the p rop er
op eration of your SUBARU.
In ad d ition, some g asoline sup p liers are now p rod uc ing reformulated
g asolines, whic h are d esig ned to red uc e vehic le emi ssions. SUBARU
ap p roves the use of reformulated g asoline.
If you are not sure what the fuel c ontains, you sho uld ask your servic e
station op erators if their g asolines c ontain d eterg ents and oxyg enates
and if they have b een reformulated to red uc e vehic l e emissions.
As ad d itional g uid anc e, only use fuels suited for y our vehic le as ex-
p lained b elow. Fuel should b e unlead ed and have an oc tane rating n o lower than
that sp ec ified in this manual. Methanol (methyl or wood alc ohol) is sometimes mixe d with un-
lead ed g asoline. Methanol c an b e used in your vehic le ONLY if it
d oes not exc eed 5% of the fuel mixture AND if it is ac c omp anied b y

7-8
7. Fasten your seatb elt. Chec k that your p asseng ers
have fastened their
seatb elts.
8. Chec k the op eration of the warning and ind ic ator lig hts when the ig ni-
tion switc h is turned to the “ON ” p osition.
9. Chec k the g aug es, ind ic ator and warning lig hts af ter starting the en-
g ine. NOTE Engine oil, engine coolant, brake fluid, washer fluid and other fluid
levels should be checked daily, weekly or at fuel stops.
Starting the engine
CAUTION
Do not operate the starter motor continuously for more than ten
seconds. If the engine fails to start after operating the starter forfive to ten seconds, wait for ten seconds or more before tryingagain.
Starting the engine for a manual transmission vehicle
1. Ap p ly the p arking b rake.
2. Turn off unnec essary lig hts and ac c essories.
3. Press the c lutc h p ed al to the floor and shift the shift lever into neutral.
Hold the c lutc h p ed al to the floor while starting t he eng ine. The starter
motor will only op erate when the c lutc h p ed al is p r essed fully to the floor.
4. Turn the ig nition switc h to the “ON ” p osition and c hec k the op eration
of the warning and ind ic ator lig hts. Refer to the “Warning and ind ic ator
lig ht ” sec tion (c hap ter 3).
5. Turn the ig nition switc h to the “START ” p osition without d ep ressing
the ac c elerator p ed al. Release the key immed iately after the eng ine has
started .
If the eng ine d oes not start within ten sec ond s, wa it a while and then turn
the ig nition switc h to the “START ” p osition ag ain while d ep ressing the ac -
c elerator p ed al half way d own.

Starting and operating7-11
–
CONTINUED –
Manual transmission
WARNING
Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutralposition. Engine braking has no effect in either of these condi-tions and the risk of an accident is consequently increased.
CAUTION
Shift into reverse ONLY when the vehicle has completelystopped. It may cause damage to the transmission to try shiftinginto reverse when the vehicle is moving.
The manual transmission is a fully sync hromeshed 5- forward and 1-re-
verse sp eed transmission.
OM-H2241
The shift p attern is shown on the shift lever knob . When shifting from 5th
g ear to reverse g ear, first return the shift lever to the neutral p osition then
shift into reverse g ear.
To c hang e g ears, fully d ep ress the c lutc h p ed al, mo ve the shift lever,
and g rad ually let up on the c lutc h p ed al.
If it is d iffic ult to shift into g ear, p ut the tran smission in neutral, release the
c lutc h p ed al momentarily, and then try ag ain.

Starting and operating7-17
–
CONTINUED –
shift normally. NOTE In some cases, depressing the brake pedal on a downhill grade
does not result in an automatic downshift to 3rd gear. This canhappen when the automatic transmission fluid temperature is
very low, for example, during driving shortly after the vehicle has
been parked for an extended period of time. When the ATF tem-perature has risen to a certain level, automatic downshift normal-ly takes place. In the meantime, downshift manually for enginebraking as required.Also, downshifting when braking downhill will not occur at
speeds above approximately 50 mph (80 km/h).
3 (Third)
This p osition is for using eng ine b raking when g oin g d own a hill or for
c limb ing a g rad e.
The transmission automatic ally shifts into a suitab le g ear from 1st to
3rd ac c ord ing to the vehic le sp eed and the ac c elera tion you req uire.
When more ac c eleration is req uired in this p osition , p ress the ac c eler-
ator p ed al fully to the floor and hold that p ositio n. The transmission
will automatic ally d ownshift to 2nd or 1st g ear. Wh en you release the
p ed al, the transmission will return to the orig inal g ear p osition.
2 (Second)
This p osition is for using eng ine b raking when g oin g d own a hill or for
c limb ing a steep g rad e.
In this p osition, the transmission hold s in the 2nd g ear.
Use this p osition when starting off from a stand sti ll on slip p ery road
surfac es suc h as mud or snow. It will ensure g reate r trac tion.
1 (First)
This p osition is for d riving up or d own very steep g rad es, or d riving
throug h mud or sand , or on slip p ery surfac es. In th is p osition, the
transmission hold s in the 1st g ear.

7-26while fully p ulling up the p arking b rake lever.
HB4001BA
To release the p arking b rake, p ull the lever up sli
g htly, p ress the release
b utton, then lower the lever while keep ing the b utt on p ressed .
When the p arking b rake is set while the eng ine is r unning , the p arking
b rake warning lig ht c omes on. After starting the ve hic le, b e sure that the
warning lig ht has g one out b efore the vehic le is d r iven. Refer to the
“ Warning and ind ic ator lig hts ” sec tion (c hap ter 3).
When p arking your vehic le, always set the p arking b rake firmly and p ut
the shift lever in the “1 ” (1st) for an up g rad e or “R ” (Reverse) for a d own-
g rad e for manual transmission vehic les, or in the “P ” (Park) p osition for
automatic transmission vehic les. Always set the p ar king b rake firmly
when p arking your vehic le. Never rely on the transm ission alone to hold
the vehic le.
HB4015AA
HB4014AA

7-283. Push the c ontrol lever d ownward in the
“SET, COAST ” d irec tion
and release it. Then release the ac c elerator p ed al.
The vehic le will maintain the d esired sp eed .
Vehic le sp eed c an b e temp orarily inc reased while d r iving with the
c ruise c ontrol ac tivated . Simp ly d ep ress the ac c ele rator p ed al to ac -
c elerate the vehic le. When the ac c elerator p ed al is released , the ve-
hic le will return to and maintain the p revious c rui sing sp eed .
To temporarily cancel the cruise control
There are four ways to c anc el the c ruise c ontrol te mp orarily:
Dep ress the b rake p ed al.
Pull the c ontrol lever in the “CANCEL ” d irec tion. (if so eq uip p ed )
Dep ress the c lutc h p ed al (manual transmission vehic les only).
Shift the selec tor lever into the “N ” p osition (automatic transmis-
sion vehic les only).
To resume the c ruise c ontrol after it has b een temp orarily c anc eled
and with vehic le sp eed of ab out 20 mp h (32 km/h) or more, p ush the
c ontrol lever up ward in the “ACCEL, RESUME ” d irec tion to return to
the orig inal c ruising sp eed automatic ally. To turn off the cruise control
There are two ways to turn off the c ruise c ontrol:
Push the main switc h ag ain.
Turn the ig nition switc h to the “ACC ” p osition (b ut only when the
vehic le is c omp letely stop p ed ).
To change the cruising speed
n To increase the speed
1. Push the c ontrol lever up ward in the “ACCEL, RESUME ” d irec tion
and hold it until the vehic le reac hes the d esired s p eed .
When the d ifferenc e b etween the ac tual vehic le sp ee d and the set
sp eed is less than 4 mp h (6.8 km/h), the set sp eed c an b e inc reased
1 mp h (1.6 km/h) eac h time b y p ressing the c ontrol lever up ward in
the “ACCEL, RESUME ” d irec tion q uic kly within a half sec ond .
2. Push the c ontrol lever d ownward in the “SET, COAST ” d irec tion