2000 SUBARU LEGACY sensor

Keys and doors2-13
–
CONTINUED –
Security system (if equipped)
The sec urity system help s to p rotec t your vehic le a
nd valuab les from
theft. The horn sound s and the p arking lig hts flash if someone attemp ts
to b reak into your vehic le. The starter motor is al so interrup ted to p revent
starting the vehic le without a key.
The system c an b e armed and d isarmed with the remot e transmitter.
The system d oes not op erate when the key is inserte d into the ig nition
switc h.
System operation
The sec urity system will g ive the following alarm i nd ic ations when trig -
g ered : The p arking lig hts will flash and the horn will sou nd intermittently.
In ad d ition, the starter motor will not op erate. The alarm automatic ally resets after 30 sec ond s; ho wever, the
alarm will reac tivate if the vehic le is tamp ered wi th ag ain. The alarm
will c ontinue for twelve times if any sensor c ontin ues to b e ac tivated .
The alarm is trig g ered b y: Op ening a d oor, the rear g ate or trunk lid .
Ap p lic ation of p hysic al shoc k to the vehic le (e.g . b reaking g lass or
forc ed entry). Note that there are two alarm levels for shoc k: warning
and alarm. In warning mod e, the alarm d etec ts lower level vib rations
and trig g ers 2 warning c hirp s on the horn and two f lashes on the
lig hts as a d eterrent to would b e vand als. In alarm mod e, hig her lev-
els of shoc k are d etec ted and the system will g o in to full alarm.
Ig nition switc h b eing turned on while in armed stat e.

Keys and doors2-19
–
CONTINUED –

Disarming the system
To d isarm the system, b riefly p ress the “UNLOCK/DISARM ” b utton on
the transmitter. Tripped sensor identification
If the horn sound s four times and the p arking lig ht s flash four times
when you d isarm the system, this ind ic ates that the alarm was trig -
g ered . The numb er of times the ind ic ator lig ht flas hes ind ic ates what
sensor c aused the alarm c ond ition.
To enter id entific ation mod e:
1. Op en the d river ’s d oor and leave it op en.
2. Turn the ig nition switc h to the “ON ” p osition two times. ( “LOCK ” 
“ ON ”  “ LOCK ”  “ ON ”  “ LOCK ”)
3. The ind ic ator lig ht will start flashing .
The ind ic ator lig ht p rovid es the following ind ic ati ons.
Flashing one time: Any d oor, the rear g ate or the trunk lid has b een
op ened .
Flashing three times: The imp ac t sensor in the system ’s unit has
b een ac tivated . This may ind ic ate that your vehic le has b een shoc ked
or tamp ered with b y some outsid e forc e and /or unaut horized p erson.
Flashing four times: The ig nition switc h has b een turned on.
To exit this mod e, c lose the d oor and turn the ig ni tion switc h to the
“ ON ” p osition.

Instruments and controls3-29
–
CONTINUED –

By p ressing and releasing the left b utton, the auto matic d imming
func tion is tog g led on or off. When the automatic d imming func tion is
on, the auto d imming ind ic ator lig ht (g reen) loc ate d to the rig ht of the
b utton will illuminate. By p ressing and releasing the rig ht b utton, the c om p ass d isp lay is
tog g led on or off. When the c omp ass is on, an illum inated c omp ass
read ing will ap p ear in the lower p art of the mirror .
Even with the mirror in anti-g lare mod e, the mirror surfac e turns b rig ht
if the transmission is shifted into reverse. This i s to ensure g ood rear-
ward visib ility d uring reversing . n Photosensors
HB6020BA
The mirror has a p hotosensor attac hed on b oth the f ront and b ac k
sid es. If the g lare from the head lig hts of vehic les b ehind you strikes
the mirror, these sensors d etec t it and make the re flec tion surfac e of
the mirror d immer to help p revent you from b eing b l ind ed . For this
reason, use c are not to c over the sensors with stic kers, or other simi-
lar items. Period ic ally wip e the sensors c lean usin g a p iec e of d ry soft
c otton c loth or an ap p lic ator. n Compass calibration
1. For op timum c alib ration, switc h off all nonessent ial elec tric al ac -
c essories (rear wind ow d efog g er, heater/air c ond iti oning system,
sp otlig ht, etc .) and ensure all d oors are shut.
2. Drive to an op en, level area away from larg e meta llic ob jec ts or

Audio5-25
–
CONTINUED –
n
When cassette tape is in the player
When the “TAPE ” b utton 9 is p ressed , the d isp lay will show “PLAY ”
and the p layer will start p layb ac k. Tape travel indicators
These ind ic ate the d irec tion the c assette tap e is m oving .
: ind ic ates that the top sid e of the c assette is b eing p layed b ac k.
: ind ic ates that the b ottom sid e of the c assette i s b eing p layed
b ac k. Program switching button (PROG)
When the p rog ram switc hing b utton “PROG ”
I is p ressed d uring
p layb ac k, the tap e travel ind ic ators will switc h an d the p layer will b e-
g in p laying b ac k the op p osite sid e of the tap e. The same mec hanism
is automatic ally ac tivated when the end of the tap e is reac hed . This
allows the op p osite sid e of the tap e to p lay, p rovi d ing c ontinuous
p layb ac k. Fast-forward button (FF)
To fast-forward the tap e, p ress the “FF ” b utton
T. The d isp lay will
show “FF ”. To stop fast-forward ing , p ress the “FF ” or “TAPE ” 9 b utton.
Rewind button (REW)
To rewind the tap e, p ress the “REW ” b utton Y. The d isp lay will ind i-
c ate “REW ”. To stop rewind ing , p ress the “REW ” or “TAPE ” 9 b utton.
Eject button (
)
When “
” b utton W is p ressed , p lay b ac k stop s and the c assette
tap e is ejec ted .
The ejec tion func tion also op erates when the ig niti on switc h is in the
“ LOCK ” p osition. Always make c ertain that you remove the c assette
tap e. Tape program sensor button (TPS)
n Blank skip
When the “TPS ” b utton
E is p ressed , the “TPS ” ind ic ator will c ome on
and the p layer will automatic ally skip any b lank p o rtion of 15 sec ond
or more and p lay the next p rog ram, even if it is on the other sid e. To
c anc el b lank skip mod e, p ress the “TPS ” b utton ag ain.

Audio5-27
–
CONTINUED –
* Noise red uc tion system manufac tured und er lic ense
from Dolb y Lab oratories
Lic ensing Corp oration. “Dolb y ” and the d oub le-D Symb ol are trad e marks of
Dolb y Lab oratories Lic ensing Corp oration.
Auto metal sensor
The c assette p layer automatic ally ad justs for metal or CrO
2 tap e.
Compact disc player operation
HB5042DB
O SCAN b utton
P Disc slot
A Ejec t b utton
S Rand om b utton D
Rep eat b utton
F Trac k selec tion b uttons
G CD (CD p layer selec tion)
b utton
To play back a compact disc
n When CD is not in the player
Hold a d isc with a fing er in the c enter hole while g rip p ing the ed g e of
the d isc , then insert it in to the slot (with the l ab el sid e up ) and the
p layer will automatic ally p ull the d isc into p ositi on.
A sing le CD (8 c m/3 inc h CD) may also b e used witho ut any ad ap ter.