Page 260 of 322
10-4
Always use the proper tools and make certain that they are
well maintained. Never get under the vehicle supported only by a jack. Always
use a safety stand to support the vehicle. Never keep the engine running in a poorly ventilated area,
such as a garage or other closed areas. Do not smoke or allow open flames around the fuel or battery.
This will cause a fire. Wear adequate eye protection to guard against getting oil or
other fluids in your eyes. If something does get in your eyes,
thoroughly wash it out with clean water. Because the fuel system is under pressure, replacement of the
fuel filter should be performed only by your SUBARU dealer. The SRS airbag has no user-serviceable parts. Tampering with
or disconnecting the system ’s wiring could result in accidental
inflation of the airbag or could make the system inoperative,
which may result in serious injury. The wiring harnesses of theSRS airbag system are covered with yellow insulation and the
connectors of the system are yellow, for easy identification. Donot use electrical test equipment on any circuit related to the SRSairbag system. For required servicing of the SRS airbag, see your
nearest SUBARU dealer. Before checking or servicing in the engine compartment
Always stop the engine and set the parking brake firmly to pre-
vent the vehicle from moving. Always let the engine cool down. Engine parts become very
hot when the engine is running and remain hot for some time af-ter the engine is stopped. Do not spill engine oil, engine coolant, brake fluid or any other
fluid on hot engine components. This may cause a fire. Always remove the key from the ignition switch. When the
ignition switch is in the “ON” position, the cooling fan may oper-
ate suddenly even when the engine is stopped.
Page 262 of 322
10-6Engine compartment overview 1
Manual transmission oil level
g aug e (MT) (p ag e 10-19) or
Differential g ear oil level
g aug e (AT) (p ag e 10-22)
2 Air c leaner element
(p ag e 10-16)
3 Clutc h fluid reservoir
(p ag e 10-28)
4 Automatic transmission fluid
level g aug e (p ag e 10-20)
5 Brake fluid reservoir
(p ag e 10-26)
6 Fuel filter 7
Wind shield washer tank
(p ag e 10-31)
8 Fuse b ox (p ag e 10-42)
9 Battery (p ag e 10-29)
Q Eng ine oil filler c ap
(p ag e 10-7)
W Eng ine c oolant reservoir
(p ag e 10-13)
E Eng ine oil level g aug e
(p ag e 10-7)
R Power steering fluid reservoir
(p ag e 10-25)
T Rad iator c ap (p ag e 10-13) HGA017BB
Page 264 of 322
10-8
Changing the oil and oil filter
Chang e the oil and oil filter ac c ord ing to the main tenanc e sc hed ule in
the “Warranty and Maintenanc e Booklet ”.
The eng ine oil and oil filter must b e c hang ed more freq uently than
listed in the maintenanc e sc hed ule when d riving on d usty road s,
when short trip s are freq uently mad e when towing a trailer, or when
d riving in extremely c old whether.
1. Warm up the eng ine b y letting the eng ine id le for ab out 10 minutes
to ease d raining the eng ine oil.
2. Park the vehic le on a level surfac e and stop the eng ine.
3. Remove the oil filler c ap .
HS0174
Drain plug
4. Drain out the eng ine oil b y removing the d rain p l ug while the en-
g ine is still warm. The used oil should b e d rained into an ap p rop riate
c ontainer and d isp osed of p rop erly.
WARNING
Be careful not to burn yourself with hot engine oil.
5. Wip e the seating surfac e of the d rain p lug with a c lean c loth and
tig hten it sec urely with a new sealing washer after the oil has c om-
p letely d rained out.
Page 265 of 322
Maintenance and service10-9
–
CONTINUED –
HS0176
HS0175
Drain plugSealing washer
Oil filter
6. Remove the und er c over.
7. Remove the oil filter with an oil filter wrenc h.
8. Before installing a new oil filter, ap p ly a thin c oat of eng ine oil to the
seal.
9. Clean the rub b er seal seating area of the lower c rank c ase and
install the oil filter b y hand turning . Be c areful not to twist or d amag e
the seal.
10. Tig hten it ap p roximately two-third s of a turn af ter the seal makes
c ontac t with und ersid e of the c rank c ase.
CAUTION
Never over tighten the oil filter because that can result in an oilleak.
11. Reinstall the und er c over.
12. Pour the sp ec ified amount of eng ine oil throug h the filler nec k.
Oil c ap ac ity: 4.2 US q t (4.0 liters, 3.5 Imp q t)
13. Start the eng ine and make sure that no oil leaks ap p ear around
the filter ’s rub b er seal.
14. Run the eng ine until it reac hes the normal op era ting temp erature.
Then stop the eng ine and wait a few minutes to allo w the oil d rain
b ac k. Chec k the oil level ag ain and if nec essary, a d d more eng ine oil.
