2000 SKODA FABIA check engine

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 8 02
Every 240 000 km (QG0)
Includes: Inspection every 120 000 km and additional operations stated in the table below
Inspection Service (QG1, QG2)
♦Vehicles with WIV (QG1) must be filled with oils which conform to the VW standard 503 00 (petrol engines) VW
506 00 (SDI, TDI diesel engines) or VW 506 01 (TDI PD diesel engines), possibility of damage when using other
oils.
♦Vehicles with WIV which have been filled with oils which do not conform to the VW standard 503 00 or VW 506 00
or VW 506 01, must be coded in the WIV with a fixed oil change limitation (QG2) ⇒Chapter 02-6. Work involvedChapter
–Replace tensioning pulley (PD diesel engine as of 08.03)02-3
♦Every 2 years - in addition change brake fluid
♦Every 4 years - replace contents set for tyre repair
♦Every 90 000 km - replace the guide pulley and the tensioning pulley (PD diesel engine up to 07.03)
♦Every 120 000 km - replace the timing belt and the guide pulley (038 109 244 H) (diesel engines as of 05.01 to
04.02 except the PD engine)
♦Every 120 000 km - Replace the timing belt (PD Diesel engine as of 08.03)
♦Every 150 000 km - replace the timing belt (diesel engines as of 05.02 and with the guide pulleyr 038 109 244
M) - except on the TDI PD engine
♦Every 240 000 km - Replace the tensioning pulley (PD Diesel engine as of 08.03)
♦Exhaust-emission analysis (EEA). Expiry date - see EEA tag on the vehicle identification plate (only valid for
some countries)
♦At each inspection - check the 'use by date' of the first aid kit
♦Recommendation: Replace windscreen wiper blades every 2 years
Note
Work involvedChapter
–Interrogate fault memory of all systems, if necessary erase02-6
–Visual inspection: Engine and components in the engine compartment for leaks and dam-
age02-3
–Change the engine oil, replace the oil filter02-3
–Conduct a visual inspection of the airbag units for external damage02-7
–Reset service interval display02-6
–Inspecting brake system for leaks and damage02-5
–Check the thickness of the brake pads on all wheels02-5
–Check gearbox, final drive, drive shafts and joint boots for leaks and damage
–Axle joints: Inspect boots for leaks and damage
–Track rod ends: Inspect play and correct attachment of boots

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 9 02
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper operation,
washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Inspect operation of tilting roof and grease the runners02-7
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Draining the fuel filter (diesel engine)
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Air filter: Clean the housing, replace the insert every 4 years or 60.000 km.02-3
–Replace the fuel filter (diesel engine with fuel operation, which does not comply with DIN
EN 590-standard)
–Ribbed V-belt: Inspect condition and for vehicles without tensioning pulley also the ten-
sion - every 60.000 km02-3
–Replace the fuel filter (diesel engine) - every 60.000 km
–Spark plugs: replace - every 60.000 km.02-3
–Automatic gearbox: Check the ATF level, and top up if necessary, every 60.000 km
–Check the timing belt for the camshaft on a 4-cylinder petrol engine at 90.000 km and
then every 30.000 km after that
–Replace the emergency battery for the alarm system - every five years02-6
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form Work involvedChapter

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 7 02
Replace engine oil filter
Vehicles with petrol engine
Special tools, test and measuring equipment and
auxiliary items required
♦Oil filter wrench
–Release oil filter (e.g. Würth, Hazet) and remove.
–Clean sealing surface at engine.
–Oil rubber seal slightly.
–Screw in new filter and tighten by hand.
–After filling with oil, run engine until it is at operating
temperature and inspect for leaks.
Vehicles with diesel engine
Special tools, test and measuring equipment and
auxiliary items required
♦Oil filter wrench -3417- or wrench 36
–Release cap -1-.
–Replace O-rings -2- and -3- as well as oil filter element
-4-.
–Tighten cap -1-.
Tightening torque of the cap: 25 Nm
Replacing timing belt and tensioning
pulley for camshaft drive (1.9 TDI en-
gines)
–Removing and installing the timing belt
⇒Rep. Gr. 13; 1.9/74 TDI Engine, Mechanics, or
⇒Rep. Gr. 13; 1.9/96 TDI Engine, Mechanics.
Replacing timing belt and tensioning
pulley for camshaft drive (1.4 TDI en-
gines)
–Removing and installing the toothed belt
⇒Rep. Gr. 13; 1.4/55 TDI Engine, Mechanics.
Inspecting timing belt for camshaft drive
for wear and running (petrol engine)
Check timing belt for:
♦Tears or splits -A-, cross-sectional fractures
♦Lateral catches -B-
♦Fraying or chunking -C-
♦Crack in the base tooth -D-
♦Separation of layers (timing belt housing, cords)
♦Traces of oil and grease
S02-0339
2
1
4
3

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 10 02
Only use engine oils:
QGO, QG2
Specification VW 505 01 or VW 505 00 (oil according
to VW 505 00 cannot be used for TDI PD - engines)
Oils may be intermixed when topping up.
In exceptional cases:
Multigrade oils according to ACEA B3 or B4. Such oils
must only be used once for topping up within the speci-
fied oil change interval if, in exceptional cases, no ap-
proved engine oil is available.
QG1
Specification VW 506 01 or VW 506 00 (oil according
to VW 506 00 cannot be used for TDI PD - engines)
–Close the oil filler opening again.
–Start engine and check for leaks.
–Check the engine oil level again and top up with oil if
necessary.
–Wait at least 3 minutes after topping up the oil again
before inspecting the oil level again.
–Install the noise insulation.
The oil level must not be above the -max- marking to
avoid damage to the catalytic converter. See Inspecting
engine oil level ⇒02-3 page 8.
Inspecting antifreeze protection, replen-
ishing coolant additive if necessary
♦Collect drained coolant for proper disposal.
♦Observe the disposal instructions for the drained cool-
ant.
Special tools, test and measuring equipment and
auxiliary items required
♦Refractomer -T10007-
Inspecting antifreeze protection of the coolant
♦The refractometer -T10007- may, for example, be
used for inspecting the antifreeze protection of the
coolant.
Note
WARNING!
Coolant additives are toxic!
Do not inhale coolant vapours, do not swallow
coolant, avoid contact with skin and eyes; haz-
ardous if consumed!
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 12 02
–Perform a test drive and again check the coolant anti-
freeze protection.
Inspecting coolant level (volume)
–The coolant expansion reservoir is located on the right
of the engine compartment.
–Inspect coolant level only when the engine is not run-
ning.
Specified coolant level for the Inspection Service:
•Engine cold: between„MAX“ and „MIN“ marking.
•Engine warm: slightly above the „MAX“ marking.
♦The cooling system is filled all year round with a mix-
ture of water and antifreeze/anti-corrosion agent.
Coolant additives prevent damage from frost and cor-
rosion and the accumulation of lime scale while also
raising the boiling point of the coolant. For these rea-
sons the cooling system must always be filled all year
round with radiator antifreeze and anti-corrosion
agent offering these properties.
♦Coolant additive G12 - red in colour, complying with
standard TL VW 774 D, must not be mixed with other
coolant additives which comply with standard TL VW
774 C(B) -bluish-green in colour-. If these two coolant
additives are mixed the coolant will turn brown. Brown
coolant must be drained immediately, the cooling sys-
tem flushed out with drinking water and filled with
fresh coolant. If this is not done the engine and cooling
system may suffer damage. Engine Coolant capacity
1.2 ltr./40 kW and 1.2
ltr./47 kWapprox. 5.1 ltr.
1.4 ltr./55 kW and 1.4
ltr./74 kWapprox. 5.5 ltr.
1.0 ltr./37 kW; 1.4 ltr/
44 kW and 1.4 ltr./50
kWapprox. 6.0 ltr.
1.4 ltr./55 TDI PD approx. 6.2 ltr.
1.9 ltr./47 kW SDI approx. 6.6 ltr.
1.9 ltr./74 kW TDI PD
and 1.9 ltr./96 kW TDI
PDapprox. 6.8 ltr.
2.0 ltr./85 kW approx. 6.9 ltr.
S02-0303
WARNING!
Coolant additives are toxic!
Do not inhale coolant vapours, do not swallow
coolant, avoid contact with skin and eyes; haz-
ardous if consumed!
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 14 02
The listed G12 PLUS coolant additives may be inter-
mixed.
Ribbed V-belt: Inspect condition
Special tools, test and measuring equipment and
auxiliary items required
♦Wrench socket
Perform the following procedure:
–Raise vehicle.
–Remove bottom engine compartment cover at right.
–Use a socket wrench to crank the engine at the belt
pulley -2-.
–Check ribbed V-belt for:
♦Splits in the carcass (initial splits, splits in core, splits
across carcass).
♦Separation of layers (top layer, cords).
♦Sections of carcass broken out.
♦Fraying of cords.
♦Wear to sides (abrasion of material, frayed sides,
hardening of sides, glazed and hardened surfaces).
♦Traces of oil and grease.
♦Correct tension (vehicles without tensioning pulley).
♦It is essential to replace the V-ribbed belt if defects are
found. This will help prevent any operational prob-
lems. Replacing the ribbed V-belt is a repair measure.
♦Engines fitted with an AC compressor are equipped
with a double ribbed V-belt.
Routing of V-ribbed belt
1.0 litre/37 kW (ARV and AQV), 1.4 litre/44 kW (AZE
and AZF), 1.4 litre/50 kW (AME, ATZ and AQW) with-
out air-conditioning
1 - Crankshaft
2 - Tensioning pulley
3 - Coolant pump
4 - AC generator
Note
S02-0025
Note

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
EnginesEdition 09.04
S00.5301.14.2002-3 page 18 02
Replace air filter element
–Open the filter housing.
–Replace the filter element and clean the filter housing.
–Close filter housing and check correct fitting.
Replacing the fuel filter (diesel engine)
♦Make sure no diesel fuel comes into contact with the
coolant hoses. If necessary clean the hoses immedi-
ately!
♦It is absolutely necessary to observe the oil disposal
instructions!
♦Observe the disposal instructions!
Removing
–Remove retaining clips -3-.
–Remove regulating valve -4- with the connected fuel
hoses.
–Remove fuel hoses -1- and -2- on the filter.Engine fitted Spark plug manufac-
turer's designationParts No. Electrode spacing
1.0 litre/37 kW NGK BKR 6ETA-10 101 000 065
AA1.0 mm
1)
1) Distance between earth electrode and spark plug insulator.
1.2 ltr./40 kW AWY NGK PZFR5J-11 101 905 600
1.0 mm1)
NGK ZFR 5P-G 101 905 617
0.9 mm1)
BOSCH F7 HER2 101 905 601 B
0.9 mm1)
BMD NGK ZFR 5P-G 101 905 617
0.9 mm1)
BOSCH F7 HER2 101 905 601 B
0.9 mm1)
Brisk DOX 15 LE 101 905 618
0.9 mm1)
1.2 ltr./47 kW BOSCH F7 HER2 101 905 601 B
0.9 mm1)
NGK ZFR5P-G 101 905 617
0,8 mm1)
1.4 ltr./44 kW Brisk DR 15 TC 101 000 060
AA0,8 mm1)
1.4 ltr./50 kW Champion RC-89 PYC 101 000 049
AC0.8 mm1)
1.4 ltr./55 kW AUA, BBY NGK BKUR 6ET-10 101 000 033
AA1.0 mm1)
BKY BERU 14F-7 HUR 2 101 905 603 B
0.9 mm1)
1.4 ltr./74 kW NGK BKUR 6ET-10 101 000 033
AA1.0 mm1)
2.0 ltr./85 kW NGK BKUR 6ET-10 101 000 033
AA1.0 mm1)
Note
1
2
3
4
S02-0323

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
GearboxEdition 07.03
S00.5301.12.2002-4 page 1 02
02-4 Gearbox
Gearbox/Final drive: Check the oil level
and top it if necessary
5 speed gearbox 002
Gearbox oil specification: G50 SAE 75W90 (synthetic oil)
–Unscrew plug for inspecting gear oil -arrow-.
The oil is at the correct level if the gear is filled up to the
lower edge of the oil filler hole.
–Tighten plug -arrow-, 25 Nm.
When topping up, pay attention to the following
points:
–Unscrew plug for inspecting gear oil -arrow-.
–Pour in gear oil up to lower edge of the filler hole.
–Screw in plug -arrow-.
–Start engine, engage a gear and allow gearbox to ro-
tate for about 2 minutes.
–Switch off engine, unscrew plug -arrow- and top up
gear oil to lower edge of the filler hole.
–Tighten plug -arrow-, 25 Nm.
5 speed gearbox 02R
Gearbox oil specification: G50 SAE 75W90 (synthetic oil)
–Remove noise insulation panel -arrows-.
–Unscrew plug for inspecting gear oil -arrow-.
The oil is at the correct level if the gear is filled up to the
lower edge of the oil filler hole.
–Tighten plug -arrow-, 30 Nm.
When topping up, pay attention to the following
points:
–Unscrew plug for inspecting gear oil -arrow-.
–Pour in gear oil up to lower edge of the filler hole.
–Screw in plug -arrow-.
–Start engine, engage a gear and allow gearbox to ro-
tate for about 2 minutes.
–Switch off engine, unscrew plug -arrow- and top up
gear oil to lower edge of the filler hole.
–Tighten plug -arrow-, 30 Nm.
5 speed gearbox 02T
Special tools, test and measuring equipment and
auxiliary items required
♦Socket wrench insert -T30023 (3357)-
S34-0408
S10-0101
S34-0498