2000 SKODA FABIA AUX

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 3 02
holding the knob in the left or right position respective-
ly.
Connect vehicle system tester and inter-
rogate fault memory
The stored faults can be read out with vehicle system
tester -V.A.G 1552-, -V.A.G 1551-, or -V.A.S. 5051-.
♦The following description relates to vehicle system
tester -V.A.G 1552- using program card 6.0.
♦The use of vehicle diagnosis, measurement and infor-
mation system -V.A.S 5051- or fault read-out scan
tool -V.A.G 1551- with the program card version 9 is
similar. (A minor deviation on the display read-out is
possible).
Special tools, test and measuring equipment and
auxiliary items required
♦Vehicle system tester -V.A.G 1552 -
♦Diagnostic cable -V.A.G 1551/3, 3A, 3B oder 3C-
Test conditions
•Battery voltage at least 9 V.
•All fuses OK.
•Earth connections between the engine (on gearbox
housing) and body (below the battery) must be O.K.
–Apply handbrake.
–Gearbox: Put the lever into Neutral.
–Automatic gearbox: Move selector lever into position
„P“ or „N“.
–Fold cover open -1- in the direction of the arrow.
Connect vehicle system tester - V.A.G 1552- with appro-
priate cable.
–Start engine and run in idle.
If the read-outs as shown in the work sequence are not
displayed, refer to the following notes:
♦If „Error in data transmission“ is displayed because of
an incorrect entry, unplug cable from vehicle system
tester, plug in again and repeat all the steps.
♦If one of the following messages appears in the dis-
play, carry out fault finding as specified in the fault
finding program at the diagnostic cable ⇒Current
Flow Diagrams, Electrical Fault Finding and Fitting Lo-
cations, or ⇒Operating Instructions of vehicle sys-
tem tester
Note
1552V.A.
G
.H
E
LPQ O C9 8 76 5 43 2 1
Note
Vehicle system test HELP
The control unit does not respond
Vehicle system test HELP
Fault in communication set-up

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 10 02
–Connect -V.A.G 1552-.
–Switch on ignition.
–Enter address word 17 „Dash Panel Insert“ and con-
firm with .
Readout on display (e.g.):
–Note the dash panel insert coding.
–Press key.
Readout on display (e.g.):
–Press key.
Readout on display:
–Enter function 07 „Code control unit“ and confirm with
key.
Readout on display:
–Enter dash panel insert coding which is identical to the
original coding. The value on the fourth position must,
however, be altered from 1 to 2.
XXX1X - QG1
XXX2X - QG2
Readout on display (e.g.):
–Confirm the entry with key .
Readout on display (e.g.):
–Press key.
Readout on display (e.g.):
–Press key.
Readout on display:
–Enter 06 for „End output“.
Readout on display:
–Confirm the entry with key .
–Switch off ignition.
–Switch off -V.A.G 1552-.
Inspecting headlight beam setting and
adjusting if necessary
Special tools, test and measuring equipment and
auxiliary items required
♦Headlight beam setting device
In principle the following inspection and setting descrip-
tion applies for all countries. However, comply with na-
tional guidelines and legislation of the relevant country.
⇒Operating instructions for the headlight beam setting
device
Q
6Y1919870B COMBIINSTRUMENT VDO X09 ->
Coding 03111 WSC 12345

TMBMC46Y0Y7000001 SKZ7Z0W0204038 ->


Vehicle system test HELP
Select function XX
Q
Coding control unit
Enter code number XXXXX (0-32767)
Coding control unit
Enter code number 03121 (0-32767)
Q
6Y1919870B COMBIINSTRUMENT VDO X09 ->
Coding 03121 WSC 12345

TMBMC46Y0Y7000001 SKZ7Z0W0204038 ->


Vehicle system test HELP
Select function XX
Vehicle system test HELP
06 End output
Q

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Exhaust-emission AnalysisEdition 09.04
S00.5301.14.2002-8 page 5 02
All tubes and plug connections, which had been removed
or disconnected for the test and adjustment, must be re-
inserted or connected.
Technical data of the spark plugs Chapter 02-3.
Exhaust-Emission Analysis on Models
with Diesel Engines
♦When possible the test should be carried out immedi-
ately after the road test and also outdoors. If specific
reasons prevent this (weather conditions, excessive
noise in residential areas) the test may also be per-
formed in the workshop.
♦Secure the engine bonnet in the first stop while meas-
uring to reduce the noise.
Visual inspection
♦Hose for crankcase ventilation is connected
♦Fuel system and injection pump must be tight
♦The exhaust system must be undamaged and tight
♦All vacuum hoses are connected
Test and setting conditions
•Engine oil temperature at least 80 °C
•All electrical components disconnected
•No fault stored in the fault memory ⇒Chapter 02-6,
connect vehicle system tester and interrogate fault
memory
Correct detected faults before measuring (repair meas-
ure).
Connect the test equipment
–Connect the tester in compliance with the operating
instructions.
–Start engine, warm up to normal temperature and run
in idle.
–Perform the exhaust-emission analysis.
♦Activate and inspect auxiliary equipment such as e.g.
power steering, automatic gearbox or air conditioning
system. Check whether the engine continues to run
perfectly under this load.
♦All tubes and plug connections, which had been re-
moved or disconnected for the test and adjustment,
must be re-inserted or connected.
Note
Note
Note
Note