Page 11 of 181
Downloaded from www.Manualslib.com manuals search engine 1
Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:25-page12
1.06
AUTOMATIC LOCKING OF DOORS, ETC. WHEN DRIVING
You can decide if you wish to
activate the function.
To activate it
With the ignition on, press the
locking side (red dot) of the door
central locking button1for
approximately 5 seconds until you
hear a beep.To deactivate it
With the ignition on, press the
unlocking side (opposite the red
dot) of the door central locking
button1for approximately 5
seconds until you hear a beep.
If you decide to keep the
doors locked when you
are driving, remember
that it may be more
difficult for those assisting you
to gain access to your vehicle in
the event of an emergency.
Operating principle
When the vehicle moves off, the
system automatically locks the
doors, etc. as soon as a speed of 4
mph (6 km/h) is attained.
Unlocking occurs automatically:
- if a front door is opened.
- by pressing the door unlocking
button1.
Page 18 of 181
Downloaded from www.Manualslib.com manuals search engine 54
5
3
Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:25-page19
1.13
SEAT BELTS(continued)
To fasten
Unwind the beltslowly and
smoothlyand ensure the buckle3
locks into the catch5(check it is
locked by pulling on the buckle3).
If the belt jams, allow it to return
slightly before attempting to
unwind it again.
To fasten(continued)
If your belt becomes completely
jammed:
- Pull the belt slowly but firmly so
that just over an inch (3 cm)
unwinds.
- Then allow the belt to rewind
automatically.
-Unwinditagain.
- If the problem persists, consult
your Renault Dealer.
To release
Press button4on the catch5and the
seat belt will be returned by the
inertia reel.
Hold the buckle to help the
operation.
Page 40 of 181
Downloaded from www.Manualslib.com manuals search engine Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:26-page41
1.35
INSTRUMENT PANEL(continued)
The presence and operation of the warning lights, described below, depend on the vehicle equipment and
country.
7Multifunction display
• Engine oil level indicator
The vehicle must be parked
on level ground and the
engine should have been
switched off for some time
beforehand to obtain an
accurate reading.
For approximately 30 seconds
after the ignition has been
switched on:
-iftheleveliscorrect,the
display will show “oil OK”
Special feature:to gain a
more accurate reading of
the level, press the trip
mileage reset button or the
information scroll button
on the on-board computer
during these 30 seconds (on
the stalk on the right-hand
side of the steering wheel).
The squares which appear
on the display indicate the
level. The number of
squares displayed is
reduced as the oil level
drops and they are replaced
by a dash.To move to on-board computer
reading, press the button again.
- When the level is at a
minimum,thedashesand
the word “ oil” flash, “ OK” is
no longer displayed and the
SERV warning will
illuminate.
It is vital to top up the oil as
soon as possible.
• On-board computer
Canbereadapproximately
30 seconds after the ignition
is switched on.
Refer to the information in
section 1 on the on-board
computer.8Multifunction key
Press repeatedly on the key to
select information on the
display, or to reset the on-board
computer trip mileage
counter(s).
STOP light
It goes out as soon as
the engine starts.
This lights up together with
one of the warning lights:
Engine immobiliser
system indicator light
This light has several
functions.
Refer to the information
on the engine immobiliser in
section 1.
Page 44 of 181
Downloaded from www.Manualslib.com manuals search engine Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:26-page45
1.39
INSTRUMENT PANEL(continued)
The presence and operation of the warning lights described below depend on the vehicle equipment and country.
9Not used.
Handbrake “on” and
brake circuit fault
warning light
This lights up when the
handbrake is applied and then
goes out again.
If it lights up under braking at
the same time as STOP warning
light comes on, it indicates that
the fluid level is low in one of
the circuits. Press the button.
10Lights linked to the function
and/or failure of the automatic
gearbox.
Refer to the information on the
proactive automatic gearbox in
section 2.11Warning light for
monitoring exhaust gas
For vehicles equipped
with this option, the light
comes on when the ignition
isswitchedonandgoesout
within 3 seconds.
• If it remains lit, consult your
Renault Dealer as soon as
possible.
• If it flashes, reduce the
engine speed until the light
stops flashing. Consult your
Renault Dealer as soon as
possible.
Refer to the information on
anti-pollution, fuel economy
and driving in section 2.11Anti-lock brake
warning light
This lights up when
the ignition is switched on and
goes out within 3 seconds. If it
lights up when you are driving,
it indicates an incident in the
anti-lock braking system.
Braking will then occur
normally, without the anti-lock
system.
Consult your Renault Dealer as
soon as possible.
Page 45 of 181
Downloaded from www.Manualslib.com manuals search engine 3
1
2
Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:26-page46
1.40
ON-BOARD COMPUTER
1Display
2Start key and reset button on the
trip mileage counters
For example, to reset the trip
mileage, the display must be set to
“trip mileage”.
Automatic resetting
The trip mileage recorders will b
reset automatically when the
maximum capacity of any of the
memories is exceeded.3Display selection key
Keep pressing key3briefly to
show the following information
in sequence:
a) total mileage recorder,
b) trip mileage recorder,
c) fuel consumed,
d) average consumption,
e) current consumption,
f) estimated range,
g) distance covered,
h) average speed.
Display flashing
Consult a Renault Dealer if the
display flashes.
Interpreting certain values
displayed after resetting
The values showing average fuel
consumption, range and average
speed will become more stable and
reliable the further you travel since
thelasttimetheresetkeywas
pressed.For the first few miles after pressing
the reset button you will notice:
• that the range increases as you
travel. This is normal. Average
fuel consumption may decrease
when:
- The car stops accelerating.
- The engine reaches its operating
temperature (engine cold when
start button pressed).
- When you drive from a built up
area on to the open road.
Therefore, if the average fuel
consumption decreases, the range
will increase.
•Youmayalsonoticethatthe
average fuel consumption
increases when the vehicle is
stationary and the engine idling.
This is normal since the module
takes account of fuel used during
idling.
Page 46 of 181
Downloaded from www.Manualslib.com manuals search engine Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:26-page47
1.41
ON-BOARD COMPUTER(continued)
Examples of
display selection by
pressing button3:Interpreting the display
a) Total mileage recorder.
b) Trip mileage recorder.
c) Fuel consumed(in litres) since the last reset.
d) Average consumption(in mpg or l/100 km) since the last time the reset
button was pressed.
The value is displayed after driving 400 metres and takes into consideration
the distance travelled and the fuel used since the last time the reset button
was pressed.
Page 47 of 181
Downloaded from www.Manualslib.com manuals search engine Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:26-page48
1.42
ON-BOARD COMPUTER(continued)
Examples of the
display by pressing
button3Interpreting the display
e) Current consumption(in mpg or litres/100 km)
The value is displayed after reaching a speed of 15 mph (25 km/h).
f) Estimated range with the remaining fuel(in miles or km)
This range takes into consideration the average fuel consumption since the
last time the reset button was pressed.
The value is displayed after driving 400 metres.
g) Distance travelled(in miles or km) since the last time the reset button was
pressed.
h) Average speed(in mph or km/h) since the last time the reset button was
pressed.
The value is displayed after driving 400 metres.
Page 52 of 181
Downloaded from www.Manualslib.com manuals search engine 3
A
2
1
43
0
Q X B I U D B * T [ G 3 D J H
MEGANE CABRIOLET NU 640-2C:\Documentum\Checkout
u640-2_eng_T1.WIN 24/2/2001 14:26-page53
1.47
HORN AND WARNING LIGHTS
Horn
Press buttons1or2on the steering
wheel bossA.
Headlight flasher
Pull stalk3towards you at right
angles to flash the headlights, even
if the lights are not in use.
“Hazard” warning lights
Press switch4.
This switch illuminates all four
direction indicators simultaneously.
It is to be used to warn other road
users if you:
• are obliged to stop for any reason
beyond your control in a
forbidden location,
• are obliged to drive under
particular conditions.
Direction indicators
Move stalk3parallel to the steering
wheel and in the direction you are
going to turn.
When driving on a motorway, the
steering wheel is not usually turned
sufficiently to return the stalk
to0automatically. There is an
intermediate position in which the
stalk may be held when changing
lanes.
It will return automatically to0
when released.
