2000 RENAULT CLIO lock

1
2
18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:04-page13
2.13
GEAR LEVER HANDBRAKEPOWER ASSISTED STEERING
To select reverse
(vehicle stationary)
Move the lever to neutral, then lift
up ring1against the gear lever knob
to select reverse gear.
The reversing lights illuminate as
soon as reverse gear is selected
(ignition on).
To release
Pull the lever up slightly, press in
button2and lower the lever to the
floor.
If you are driving with the
handbrake incorrectly released, the
red warning light on the instrument
panel will remain illuminated.
To apply
Pull the lever upwards.
The lever should travel about 10
notches to hold the vehicle. Your
vehicle has self adjusting rear brake
shoes and the handbrake should
only be adjusted during a brake
overhaul.
When the vehicle is
stationary, make sure
that the handbrake is
properly applied so that
the vehicle does not move
unintentionally.
Make sure the handbrake is
properly released when driving,
otherwise overheating may
occur.Never leave the steering on full lock
when the vehicle is parked (risk of
damaging the power assisted
steering pump).
Never switch off the
engine when travelling
downhill, and avoid
doing so when driving in
general (power steering and
brake servo will not function).

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:04-page14
2.14
ANTI-LOCK BRAKING SYSTEM (ABS)
When braking sharply, the two main
aims are to reduce the stopping
distance and to keep the vehicle
under control. However, depending
on the nature of the ground, the
atmospheric conditions and your
reactions, dangers due to loss of
adherence may exist: the wheels
may lock and directional control
may be lost. To avoid these risks,
your vehicle has been fitted with
the anti-lock braking system (ABS).
The safety enhancement is that the
brake control system prevents the
wheels from locking, even if the
brakes are applied too sharply,
allowing the vehicle to be steered
and thus its direction to be controlled.
Under these circumstances, it is quite
possible for the driver to steer the
vehicle and avoid an obstacle whilst
at the same time applying the brake.
This system also allows stopping
distances to be improved, especially
when adhesion is limited (wet roads,
slippery or uneven road surface).Although this system allows this
optimisation, the ABS system in no
way increases performance which is
physically related to the local
adherence conditions between the
tyres and the ground. You must still
follow the rules of good driving
practice (driving at a safe distance
from the vehicle in front etc.).The
fact that the vehicle’s safety has been
increased should not encourage you
to take risks.
Each time the system is activated,
you will feel a certain degree of
pulsation at the brake pedal. These
tangible signs will warn you that the
adhesion between the tyres and the
ground has reached its limit and
enable you to adapt your driving
style to suit the road conditions.Operating incidents
Two situations must be considered:
1 - The warning light is
illuminated on the instrument
panel.
Braking is still assured, but
without the action of the ABS
system. Consult a Renault Dealer
as soon as possible.
2 - The warning lights
are illuminated on the instrument
panel.
This indicates a fault in one of
the ABS braking components.
Braking may be partially assured.
It is howeverdangerous to brake
sharply,soyoumuststop
immediately as soon as traffic
conditions allow. Call for the
assistance of a Renault Dealer as
soon as possible.
The braking modulation provided by the ABS system is independent of the force applied at the pedal. In an
emergency, applyfirm, continuous pressureat the brake pedal - there is no need to pump it repeatedly.

1
A
3
B
2
18IUB*ET[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T3.WIN 30/9/2000 11:27-page15
3.15
INTERIOR LIGHTING
LightA
Tilt light1to give:
- continuous lighting,
- lighting controlled, depending on
version, by the opening of one of
the front doors, or by one of the
four doors. It only extinguishes
when the doors concerned are
correctly closed.
LightB
Tilt switch2to give:
- Continuous lighting.
- Lighting controlled, depending on
version, by opening one of the
front doors, or by one of the four
doors. It only extinguishes when
the doors concerned are correctly
closed.
- No illumination of the light.
- Illumination of map reading light3.
Adjust map reading light3to the
required position.Automatic operation of the
interior lights (for certain vehicles)
•remote unlocking of the doors
illuminates the interior lights for
approximately 15 seconds;
• remote locking of the doors
extinguishes the interior lights
immediately;
• if a door remains open (or is not
correctly closed), the interior
lights will remain illuminated for
approximately 15 minutes;
• if all the doors are closed, when
the ignition is switched on, the
interior lights will start to dim.

2
1
43
18IUB*ET[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T3.WIN 30/9/2000 11:27-page19
3.19
MANUAL SUNROOF
Opening
To the first stage
Tilt handle1forwards until it locks.
To the second stage
Press lever2and simultaneously tilt
handle1until the mechanism locks
again.
Closing
Keep lever2depressed and return
handle1to its original position.
• Check that the sunroof is
correctly closed before leaving
the vehicle.
• Clean the seal every three months
using products provided by
our Technical Department
Removal
Open the sunroof to the first stage.
Press button4(if necessary, using a
tool such as a flat screwdriver) to
release the pin3from handle1:the
pin should be freed.
Lift the sunroof glass almost vertically
and release it from its hinges.
Refitting
Refitting is the reverse of removal.
Ensure pin3is correctly locked in
position.

1
A
2
B
3
4
3
4
18IUB*ET[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T3.WIN 30/9/2000 11:27-page25
3.25
REAR BENCH SEAT(operation)
The seat base and the seatback may
be folded down (in one or two
sections) to allow bulky objects to
be carried
To fold down the seat base
Lift seat baseA, against the front
seats.
To fold down the seatback
Remove the rear head restraints (if
they are fitted to the vehicle). Press
button2and lower the seatbackB.
Removing the seat base
Lift the seat base to remove brackets3
from their housing4.
To refit the seat base,carry out the
operations in reverse order to
removal.Ensure the seat base is
correctly secured.
• When refitting the seatback, ensure it is correctly locked at the top. If seat covers are being used,
check that they are not preventing the seatback locking mechanism from operating correctly.
• When moving the bench seat, check that the seat belt housings1are correctly positioned before
folding down the seat base.
Once the bench seat is in place again, ensure the seat belts are correctly repositioned.

1
2
18IUB*ET[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T3.WIN 30/9/2000 11:27-page26
3.26
LUGGAGE COMPARTMENT
For versions with electric central
door locking:
The luggage compartment is locked
and unlocked at the same time as
the doors.
The luggage compartment may
however be locked and unlocked
without affecting the doors by using
the door key in lock1.
To open
Press button1and lift the tailgate.
To close
Lower the tailgate, using the interior
recessed handle2to help you.
When the tailgate is at shoulder
height, release handle2and close
the tailgate by pushing it down from
the outside.

1
2
4
2
3
5
18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout_47\Nu607-8gb_T4.WIN 16/10/2000 11:23-page2
4.02
BONNET
Opening the bonnet
To open, pull handle1.
Bonnet safety lock
To unlock, lift lever2.
Lift the bonnet, release the strut4
from its mounting3. For your safety,
thismustbe placed in location5.
Closing the bonnet
To close the bonnet, replace strut4
in its mounting3,hold the bonnet
in the middle and lower it to 20 cm
above the closed position. Now
release it and it will lock under its
own weight.
Check that the bonnet is correctly
locked.
Check that nothing has been left in
the engine compartment before
closing the bonnet.
Ensure it is correctly
locked.
Take care when working
under the bonnet as the
engine cooling fan may
cut in at any moment.

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout_47\Nu607-8gb_T4.WIN 16/10/2000 11:23-page14
4.14
INTERIOR TRIM MAINTENANCE
Whatever type of stain is on the
trim, use soapy water (if necessary
warm) based on:
• natural soap,
• washing up liquid (1 part
washing up liquid to 200 parts of
water)
Rinse with a soft, damp cloth.
Special points
Instrument glass(e.g. instrument
panel, clock, external temperature
display, radio display, etc.).
Use a soft cloth or cotton wool.
If this does not clean the glass, use a
soft cloth (or cotton wool) slightly
dampened with soapy water then
rinse with a soft cloth or damp
cotton wool.
Carefullydry with a soft dry cloth.
Cleaning products containing
alcohol may not be used under any
circumstances.Seat belts
These must be kept clean.
Use products selected by Renault's
Technical Department (Renault
Accessory Outlet) or use warm
soapy water with a sponge and dry
with a dry cloth.
Do not use cleaning agents or dyes
under any circumstances.
We have selected special products
to care for your vehicle which
may be obtained from Renault
Accessory Outlets.