2000 Oldsmobile Intrigue steering

2-31
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don't go on at all when you
signal a turn, check for burned
-out bulbs and then check
the fuse (see ªFuses and Circuit Breakersº in the Index).
A chime will sound if you leave your turn signal on for
more than 3/4 mile (1.2 km).
Headlamp High/Low-Beam Changer
To change your headlamps
from low beam to high
beam, push the lever away
from you. To change back
to low beam, pull the lever
toward you.
To flash your high beams, pull the lever toward you and
release. The lever will return to the low
-beam position.
Please note that your fog lamps (if equipped) will not
be illuminated while the headlamps are in the
high
-beam mode.
Flash-to-Pass
With the lever in the low-beam position, pull the lever toward
you momentarily to switch to high beams (to signal you are
going to pass). If you have the headlamps on, they will return
to low beams when you release the lever.
Windshield Wipers
You can control the windshield wipers by moving the
lever with the wiper symbol on it up or down. This lever
is located on the right side of the steering wheel.
For a single wiping cycle, pull down on the lever to
MIST. Hold it there until the wipers start, then let go.
The wipers will stop after one cycle. If you want more
cycles, hold the band on MIST longer.

2-32
You can set the wiper speed for a long delay or short
delay between wipes. This can be very useful in light
rain or snow. Push the lever up one click to INT
(intermittent), then turn the band, located on the lever, to
adjust the delay time. Turn the band down for a longer
delay, up for a shorter delay. The wiper speed can only
be adjusted when the lever is in the INT position, not in
HI or LO.
Be sure to clear the ice and snow from the wiper blades
before using them. If they're frozen to the windshield,
carefully loosen or thaw them. If your blades do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.Windshield Washer
At the end of the right-hand lever on the steering wheel,
there is a wiper symbol. To spray washer fluid on the
windshield, push the button on the end of the lever. The
wipers will run for several sweeps and then either stop
or return to your preset speed.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
Cruise Control
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.

2-34
2. Get up to the speed you want.
3. Press the COAST SET
button on your steering
wheel and release it.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed. It will go off when you:

Step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don't need to reset it.
Once you're going about
25 mph (40 km/h) or more,
press the RES ACCEL
button on your steering
wheel. You'll go right back
up to your chosen speed and
stay there.

2-35
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the COAST SET button on the steering wheel,
then release the button and the accelerator pedal.
You'll now cruise at the higher speed.

Press the RES ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the button. (To increase your speed
in very small amounts, press the RES ACCEL button
briefly and then release it. Each time you do this,
your vehicle will go 1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you set the
cruise control speed by pressing the COAST SET button
on the steering wheel.Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the COAST SET button on the steering wheel
until you reach the lower speed you want, then
release it.

To slow down in very small amounts, press the
COAST SET button on the steering wheel briefly
and then release it. Each time you do this, you'll
go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise speed you set earlier.

2-36
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Ending Cruise Control
There are three ways to cancel the cruise control:

Step lightly on the brake pedal,

press CLEAR on the steering wheel or

press the CRUISE button on the instrument panel.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
The lamp controls are located on the multifunction lever on
the left of the steering wheel. They control these systems:

Headlamps

Taillamps

Parking Lamps

License Lamps

Sidemarker Lamps

Instrument Panel Lights

2-51
Your instrument panel is designed to let you know at a glance how your vehicle is running. You'll know how fast
you're going, about how much fuel is in your tank and many other things you need to drive safely and economically.
The main components of your instrument panel are:
A. Side Window Defogger Vent
B. Instrument Panel Outlets
C. Turn Signal/Multifunction Lever
D. Instrument Panel Cluster
E. Windshield Wipers/Washer Fluid Lever
F. Cruise Control (CRUISE) Button
G. Hazard Button
H. Instrument Panel Fuse Block
I. Instrument Panel Dimmer
J. Fog Lamp Button
K. Fuel Door ReleaseL. Trunk Lid Release
M. Storage Bin
N. Trip Odometer
O. Tilt Wheel
P. Audio Steering Wheel Controls (If Equipped)
Q. Horn
R. Cruise Control Switches
(RES ACCEL, CLEAR, COAST SET)
S. Ignition Switch
T. Accessory Power Outlet
U. Comfort Controls
V. Audio System
W. Glove Box

2-60 Precision Control System (PCS) Warning
Light (Option)
This light should come on
briefly as you start your
engine. If the light doesn't
come on then, have it
serviced so it will be ready
to warn you if there's
a problem.
If the PCS warning light comes on, it means there may
be a problem with your Precision Control System. When
this light comes on, so will the TRAC OFF light and
both the Precision Control System and the Traction
Control System will not be functioning. If these lights
come on, try to reset the system (stop; turn off the
engine; then start the engine again). If the PCS and
TRAC OFF lights remain on, it means there is a
problem and you should see your dealer for service.
Reduce your speed and drive accordingly.
Low Traction Active (LOW TRAC) Light
Your LOW TRAC
(Low Traction Active) light
may come on for one of the
following reasons:

The Precision Control System (PCS) (if equipped) is
active and is adjusting brake pressure to help your
vehicle continue to go in the direction in which you
are steering. The PCS activates when the computer
senses that your vehicle is starting to spin, as might
happen if you hit a patch of ice or other slippery
surface on the road, and assists the driver by
selectively applying any one of the vehicle's brakes.
The system is designed to help you in bad weather or
other difficult driving situations by making the most
of whatever road conditions will allow. When the
system is on, you may hear a noise or feel a vibration
in the brake pedal. This is normal.

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Air Conditioning with Electronic Controls
3
-4 Air Conditioning
3
-5 Air Conditioning with Automatic and
Auxiliary Temperature Control (If Equipped)
3
-10 Rear Window Defogger
3
-11 Ventilation System
3
-12 Audio Systems
3
-12 Setting the Clock
3
-12 AM-FM Stereo with Cassette Tape Player and
Automatic Tone Control3
-16 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Automatic Tone
Control (If Equipped)
3
-22 Trunk-Mounted CD Changer (Option)
3
-26 Theft-Deterrent Feature
3
-28 Audio Steering Wheel Controls (If Equipped)
3
-28 Understanding Radio Reception
3
-29 Tips About Your Audio System
3
-30 Care of Your Cassette Tape Player
3
-31 Care of Your Compact Discs
3
-31 Care of Your Compact Disc Player
3
-31 Backglass Antenna