2000 MITSUBISHI MONTERO sunroof

SWS -Troubleshooting54B-26
Inspection Procedure F-1
Sunroof: Sunroof does not work at all.Probable cause
The power supply circuit of the sunroof motor assembly, the sunroof switch
ground circuit, or the sunroof motor assembly may be defective.DMalfunction of sunroof switch
DMalfunction of sunroof motor assembly
DMalfunction of harness wire or connector
NG
Repair
NG
Check the harness wire between sunroof motor assembly and
fusible link (4).
NG
Repair
NG
Check the harness wire between sunroof motor assembly and
ignition switch (IG2).
NG
Repair
NG
Repair
NG
Repair
NG
Check the harness wire between sunroof motor assembly and
fusible link (2).
NG
Check the harness wire between sunroof motor assembly and
body earth.
NG
Repair
NG
Check the harness wire between sunroof switch and body earth.
NG
Repair
OK
Replace the sunroof motor assembly.
NG
Repair
NG
Check the harness wire between sunroof switch and sunroof motor
assembly.
OK
Check trouble symptoms.
OK
Check the following connectors:
F-05, F-06
OK
Check trouble symptoms.
OK
NG
Check the following connectors:
F-05, F-02, D-29
F-05, F-02, D-29, D-207, D-209Measure at sunroof switch connector F-05.
DDisconnect connector and measure at harness side.
DContinuity between terminal 4 and body earth.
OK:Continuity
OK
Check trouble symptoms.
(4) NG
Check the following connector:
F-06
OK
Check the sunroof switch. (Refer to GROUP 42 – Sunroof.)
OK
Check trouble symptoms.
(3) NG
Check the following connectors:
F-06, F-02, D-29, D-207, D-223, D-27
OK
Check trouble symptoms.
(2) NG
Check the following connectors:
F-06, F-02, D-29, D-32, D-210, D-208
OK
Check trouble symptoms.
Measure at sunroof motor assembly connector F-16.
DDisconnect connector and measure at harness side.
DTurn the ignition switch to ON position.
(1) Voltage between terminal 1 and body earth.
OK:System voltage
(2) Voltage between terminal 2 and body earth.
OK:System voltage
(3) Voltage between terminal 3 and body earth.
OK:System voltage
(4) Continuity between terminal 5 and body earth.
OK:Continuity(1) NGCheck the following connectors:
F-06, F-02, D-29, D-27


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-27
Inspection Procedure F-2
Sunroof: Sunroof timer function does not work normally.Probable cause
The sunroof motor assembly operates the sunroof timer function, based on the
input signals from the following switches:
DIgnition switch (IG1)
DDriver’s door switch
If the function does not work normally, a defect on the relevant circuit, sunroof
motor assembly or the ETACS-ECU may be suspected.DMalfunction of driver’s door switch
DMalfunction of sunroof motor assembly
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
OK
NoNGCheck the defective input circuit. (Refer to P.54B-15, Defects Found
by input Signal Check.)
NG
Replace the ETACS-ECU.
Check trouble symptoms.Replace the sunroof motor assembly.
MUT-
IIinput signal check
DIgnition switch (IG1)
DDriver’s door switch
DSunroof switch
Is a diagnosis code output when the ignition switch is at the
OFF (LOCK) position?Ye sCarry out troubleshooting while referring to the Diagnosis Code
Chart on P.54B-9.
Inspection Procedure F-3
Sunroof: Safety mechanism does not work normally.Probable cause
The sunroof motor assembly monitorsload condition according to thecurrent,
which runs in the motor. If a predetermined current is exceeded, the sunroof
motor reverses due to safety mechanism. If the sunroof motor does not reverse
when an excessiveload is applied, the sunroof motorassembly may be
defective.DMalfunction of sunroof motor assembly
Replace the sunroof motor assembly.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-42
Inspection Procedure P-1
Ignition switch (ACC) signal is not sent to the ETACS-ECU.Probable cause
The ignition switch (ACC) input signal is used to operate the following devices. If
the signal fails, these devices will not work normally.
DWindshield wiper and washer
DRear wiper and washer
DHeadlamp washerDMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and ignition switch
(ACC).
OK
Check trouble symptoms.OK
Replace the ETACS-ECU.
Check the following connectors:
D-224, D-208Measure at ETACS-ECU connector D-224.
DDisconnect connector and measure at J/B side.
DTurn the ignition switch to ACC position.
DVoltage between terminal 2 and body earth.
OK:System voltage
Inspection Procedure P-2
Ignition switch (IG1) signal is not sent to the ETACS-ECU.Probable cause
The ignition switch (IG1) input signal is used to operate the following devices. If
the signal fails, these devices will not work normally.
DLight reminder warning buzzer function
DPower window timer function
DSunroof timer function
DIgnition key hole illumination lamp
DHeadlamp automatic shutdown function
DTurn-signal lamp
DRoom lamp dimming functionDMalfunction of ETACS-ECU
DMalfunction of harness wire or connector
NG
NG
Repair
NG
Check the harness wire between ETACS-ECU and ignition switch
(IG1).
OK
Check trouble symptoms.OK
Replace the ETACS-ECU.
Check the following connectors:
D-224, D-208Measure at ETACS-ECU connector D-224.
DDisconnect connector and measure at J/B side.
DTurn the ignition switch to ON position.
DVoltage between terminal 16 and body earth.
OK:System voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

SWS -Troubleshooting54B-52
Inspection Procedure P-17
Transmitter: Any switch signal is not sent to the
ETACS-ECU.Probable cause
The transmitter input signal is used to operate the keyless entry system. If the
signal fails, keyless entry will not work normally.DMalfunction of transmitter
DMalfunction of ETACS-ECU
Ye s
NG
Replace
OK
Replace the defective transmitter.
OK
Use an other transmitter to register the secret code. (Refer to
GROUP 42 – Keyless Entry System.)NGReplace the ETACS-ECU.
Check the transmitter battery. (Refer to GROUP 42 – Keyless
Entry System.)
Has the encrypted codebeen registered properly?NoRe-register the encrypted code. (Refer to GROUP 42 – Keyless
Entry System.)
Inspection Procedure P-18
Sunroof switch: Any switch signal is not sent to the
ETACS-ECU.Probable cause
If there is a problem with communication between the sunroof motor assembly
and the ETACS-ECU, the input signal check for the sunroof switch can no
longer be carried out. In addition, the sunroof timer function will also stop
working.DMalfunction of sunroof switch
DMalfunction of sunroof motor assembly
DMalfunction of ETACS-ECU
DMalfunction of harness wire or connector.
Ye s
NG
Repair
NG
Replace the ETACS-ECU.
OK
Replace the sunroof motor assembly.Check trouble symptoms.
NG
Check the harness wire between sunroof motor assembly and
ETACS-ECU.NG
Repair
OK
Check trouble symptoms.
Check the following connectors:
F-06, F-02, D-29, D-31, D-226
Is the sunroof operated normally?NoCheck the sunroof. (Refer to P.54B-13, Trouble Symptom
Chart.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk