2000 MITSUBISHI CARISMA Instruments and controls

INSTRUMENTS AND CONTROLS
4–30
D92C032a
Driving rangeED92C-Cb
For vehicles with MITSUBISHI genuine
audio, driving range can be displayed.
This value shows the distance (in km or
miles) that can be driven on the fuel remain-
ing in the fuel tank.NOTE
(1) When the driving range is displayed, if
the driving range drops below 50 km
(30 miles), alarm sounds and the dis-
play shows a flashing. When this oc-
curs, top up the fuel tank as soon as
possible.
Even when an item other than the driv-
ing range is currently displayed, the
alarm sounds and the driving range ap-
pears for 5 seconds when the driving
range drops to the 50 km, 25 km and
10 km (or 30 miles, 15 miles and
6 miles) levels. Then, the original item is
again displayed.
(2) The driving range varies depending on
road conditions, the manner of driving
and other related factors. Consequently,
the display should be used only as a
guide; top up the fuel tank as soon as
possible.
D92F001a
Average speedED92F-Db
For vehicles with MITSUBISHI genuine
audio, average speed can be displayed.
This value shows the average speed (in
km/h or mph) since the display was reset.
If you reset the display at the time when you
want to start the measurements, average
speed from that point of time can be dis-
played.

INSTRUMENTS AND CONTROLS
4–31
Type 1
D92G002a
To r e s e t the display, push the “DISP” button
for about 2 seconds or more.
Type 2
D92G003aD92J005a
Display brightness adjustment /
Display unit selection
ED92L-Ab
Display brightness adjustment
1. Press the “H” button while pressing
the button (A) to activate the display
brightness selection function.

INSTRUMENTS AND CONTROLS
4–32
D92J006a
2. Adjust the brightness by moving the
cursor with the “H” or “M” button.
H- Decrease brightness
M- Increase brightness
D92J004a
3. Press the “SET” button to determine
the setting. The display will return to
the original display item.
NOTE
(1) To cancel the brightness adjusting pro-
cedure before completion, press the
button (A).
(2) If the “SET” button is not pressed for
about 15 seconds or longer in the
middle of the adjustment, the currently
selected brightness is set automatically.
Then, the display returns to the original
display item.
D92J001a
Display unit selectionED92J-Ab
Originally, km/h and L/100 km are selected.
When you want to select the unit “mile”, fol-
low this procedure.
NOTE
For vehicles without MITSUBISHI genuine
audio system, only the unit of average fuel
consumption can be changed to km or miles
as you like.
1. Press the “M” button while pressing
the button (A) to activate the display
unit selection function. The currently
selected unit will appear.

INSTRUMENTS AND CONTROLS
4–33
D92J002a
2. Use the “H” or “M” button to select the
desired speed unit, then press the
“SET” button to enter the setting.
H- km
M- mile
D92J003a
3. If the km unit was selected in step 2,
the fuel consumption unit must be se-
lected continuously using the “H” or
“M” button. The currently selected unit
will appear.
Use the “H” or “M” button to select the
desired fuel consumption unit, then
press the “SET” button to enter the set-
ting.
H- L/100 km
M- km/L
D92J004a
4. Press the “SET” button to determine
the setting. The display will return to
the original display item.
NOTE
(1) For vehicles without a MITSUBISHI
genuine audio system, only the unit of
fuel consumption can be changed to km
or miles as you like.
(2) If you select “M” (mile) unit in step 2, fuel
consumption is automatically shown in
“mpg (mile per gallon)”.
(3) To cancel the unit setting procedure be-
fore completion, press the button (A).
(4) The outside temperature and clock are
not shown during the unit selecting pro-
cedure.
(5) If the “SET” button is not pressed for
about 15 seconds or longer in the
middle of the selection, the currently se-
lected unit is set automatically. Then, the
display returns to the original display
item.