2000 MERCEDES-BENZ C-Class spare tire

Acceleration Slip Regulation (ASR)
The acceleration slip regulation will engage at all vehicle speeds, if one or both drive wheels begin to lose traction
and spin in acceleration. While engaged, the yellow warning lamp in the speedometer dial flashes. With the
acceleration slip regulation engaged, the brake is applied to the spinning drive wheel until slip is brought under
control. If both drive wheels spin, the brake is applied to both drive wheels and simultaneously, engine torque is
limited, to improve the vehicle's driving stability. As traction on the road surface increases, thus allowing
acceleration without slip, the allowable engine torque also increases again and the brake is no longer applied to
drive wheels.

Important !
If the ASR warning lamp flashes, adapt your speed and driving to the prevailing road conditions.

Caution!
If the vehicle is towed with the front axle raised (see Towing the vehicle in Index), the engine must be shut off
(electronic key in steering lock position 0 or 1). Otherwise, the ASR regulation will immediately be
engaged and will apply the rear wheel brakes.

Notes:
The indicator lamp for the ASR is combined with that of the BAS The yellow BAS/ASR malfunction indicator
lamp in the instrument cluster and the yellow ASR warning lamp in the speedometer dial come on with the
electronic key in steering lock position 2. They should go out with the engine running. If the BAS/ASR malfunction
indicator lamp comes on with the engine running, a malfunction has been detected in either system. Pressing the
accelerator pedal will require greater effort. Only partial engine output will be available.
If the BAS malfunctions, the brake system functions in the usual manner, but without BAS. Have the BAS or ASR
checked at your authorized Mercedes-Benz dealer as soon as possible. With the ABS malfunctioning, the ASR
is also switched off. Driving the vehicle with varied size tires will cause the wheels to rotate at different speeds,
therefore the ASR may activate (yellow ASR warning lamp in speedometer dial comes on).
For this reason, all wheels, including the spare wheel, must have the same tire size. When testing the parking
brake on a brake test dynamometer, the engine must be shut off. Otherwise, the ASR will immediately be engaged
and will apply the rear wheel brakes. In winter operation, the maximum effectiveness of the ASR is only achieved
with Mercedes-Benz recommended M+S rated radial-ply tires and/or snow chains.


ASR Control Switch



ASR control switch located in center console To improve the vehicle's traction when driving with snow chains, or
starting off in deep snow, sand or gravel, press the upper half of the ASR switch. The ASR warning lamp, located
in the speedometer dial, is continuously illuminated. With the ASR system switched off, the engine torque
reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ASR is unavailable. Adapt your
speed and driving to the prevailing road conditions. A portion of the ASR system remains active, even with the
switch in the OFF position. If one drive wheel loses traction and begins to spin, the brake is applied until the wheel
regains sufficient traction. The traction control engages at vehicle speeds up to approximately 24 mph (40 km/h),
and switches off at 50 mph (80 km/h). Note: Avoid spinning of one drive wheel. Doing so may cause serious damage
to the drive train which is not covered by the Mercedes-Benz Limited Warranty.
The ASR warning lamp, located in the speedometer dial, starts to flash at any vehicle speed as soon as the tires
lose traction and the wheels begin to spin. To return to the enhanced vehicle stability offered by ASR: press lower
half of the switch (the ASR warning lamp in the speedometer dial goes out).


Important!
If the ASR warning lamp flashes:
• during take-off, apply as little throttle as possible,
• while driving, ease up on the accelerator.

Electronic Stability Program (ESP) (optional)
The ESP enhances directional control and reduces driving wheel spin of the vehicle under any driving condition.
Over/understeering of the vehicle is counteracted by applying brakes to the appropriate wheel to create a
counterpointing vehicle movement. The ESP warning lamp, located in the speedometer dial, starts to flash.

Important !
If the ESP warning lamp flashes, adapt your speed and driving to the prevailing road conditions.

Caution !
If the vehicle is towed with the front axle raised (see Towing the vehicle in Index), the engine must be shut off
(electronic key in steering lock position 0 or 1). Otherwise, the ESP will immediately be engaged and will apply
the rear wheel brakes.

Notes:
The indicator lamp for the ESP is combined with that of the BAS. The yellow BAS/ESP malfunction indicator lamp
in the instrument cluster and the yellow ESP warning lamp in the speedometer dial come on with the electronic key
in steering lock position 2. They should go out with the engine running. If the BAS/ESP multifunction indicator lamp
comes on permanently with the engine running, a malfunction has been detected in either system.
Pressing the accelerator pedal will require greater effort. Only partial engine output will be available. If the BAS
malfunctions, the brake system functions in the usual manner, but without BAS. Have the BAS or ESP checked at
your authorized Mercedes-Benz dealer as soon as possible. With the ABS malfunctioning, the ESP is also switched
off. Driving the vehicle with varied size tires will cause the wheels to rotate at different speeds, therefore the electronic
stability program may activate (yellow ESP warning lamp in speedometer dialcomes on).
For this reason, all wheels, including the spare wheel, must have the same tire size. When testing the parking brake
on a brake test dynamometer, the engine must be shut off. Otherwise, the electronic stability program will
immediately
be engaged and will apply the rear wheel brakes. In winter operation, the maximum effectiveness of the ESP is only
achieved with Mercedes-Benz recommended M+S rated radial-ply tires and/or snow chains.

Synchronizing ESP

If the power supply was interrupted(battery disconnected or empty), the BAS/ESP multifunction indicator lamp
may be illuminated with the engine running. Turn steering wheel completely to the left and then to the right. The
BAS/ESP malfunction indicator lamp should go out.

ESP Control Switch




ESP control switch located on center console To improve the vehicle's traction when driving with snow chains, or
starting off in deep snow, sand or gravel, press the upper half of the ESP switch. The ESP warning lamp, located in
the speedometer dial, is continuously illuminated. With the ESP system switched off, the engine torque reduction
feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. Adapt your speed and
driving to the prevailing road conditions. A portion of the ESP system remains active, even with the switch in the OFF
position.
If one drive wheel loses traction and begins to spin, the brake is applied until the wheel regains sufficient traction.
The traction control engages at vehicle speeds up to approximately 24 mph (40 km/h), and switches off at
50 mph (80 km/h).

Note:
Avoid spinning of one drive wheel. Doing so may cause serious damage to the drive train which is not covered by the
Mercedes-Benz Limited Warranty. The ESP warning lamp, located in the speedometer dial, starts to flash at any
vehicle speed as soon as the tires lose traction and the wheels begin to spin. To return to the enhanced vehicle
stability
offered by ESP: press lower half of the switch (the ESP warning lamp in the speedometer dial goes out).

First Aid Kit

1. Opening lid
The first aid kit is stored in the shelf below the rear window.


Spare Wheel, Vehicle Tools,
Storage Compartment

1. Trunk floor
2. Handle
3. Luggage bowl
4. Vehicle tools
5. Tab

Lift trunk floor and engage handle in upper edge of the trunk. To remove spare tire: Turn luggage bowl
counterclockwise and remove. To store spare tire: Place spare tire in wheel well and secure it with luggage bowl.
Turn luggage bowl clockwise to its stop. The tab must point toward front of vehicle.

Note:
Always lower trunk floor before closing trunk lid.

Wheels
Replace rims or tires with the same designation, manufacturer and type as shown on the original part. See your
authorized Mercedes-Benz dealer for further information. See your authorized Mercedes-Benz dealer for information
on tested and recommended rims and tires for summer and wi nter operation. They can also offer advice concerning
tire service and purchase.


Tire Replacement
Front tires should be replaced in sets. Rims and tires must be of the correct size and type. For dimensions, see
"Technical Data". We recommend that you break in new ti res for approx. 60 miles (100 km) at moderate speed. It is
imperative that the wheel mounting bolts be fastened to a tightening torque of 80 ft.lb. (110 Nm) whenever wheels are
mounted. For rim and tire specifications, refer to "Technical Data".

Warning !
Worn, old tires can cause accidents. If the tire tread is badly worn, or if the tires have sustained damage, replace
them. When replacing rirns, use only genuine Mercedes-Benz w heel bolts specified for the particular rim type. Failure
to do so can result in the bolts loosening and possibly an accident.


Rotating Wheels
Rotation of wheels with summer tires does not apply to m odel C 43 AMG. The wheels can be rotated according to the
degree of tire wear while retaining the same direction of travel. Rotating, however, should be carried out at the
scheduled service intervals, before the characteristic tire wear pattern (shoulder wear on front wheels and tread
center wear on rear wheels) becomes visible, as otherwise the driving properties deteriorate.

Important !
Unidirectional tires must always be mounted with arrow on tire sidewall pointing in direction of vehicle forward
movement.

Notes:
Thoroughly clean the inner side of the wheels any time you rotate the wheels or wash the vehicle underside. The use
of retread tires is not recommended. Retread tires may adversely affect the handling charac teristics and safety of the
vehicle. Dented or bent rims can caus e tire pressure loss and damage to the tire beads. For this reason, check rims
for damage at regular intervals. The rim flanges must be checked for wear before a tire is mounted. Remove burrs, if
any. Check and ensure proper tire inflation pressure after rotating the wheels. For Tire Inflation Pressure refer to
Index.


Spare Wheel (except C 43 AMG)

Important !
The spare wheel rim is mounted with a full size tire of the same type as on the vehicle, and is fully functional.
However, that spare wheel rim is weight optimized an d has a limited service life of 12 000 miles (20 000 km) use
before a standard wheel rim must replace it. In the case of a flat tire, you may temporarily use the spare wheel. Do
not operate vehicle with more than one spare wheel mounted.
Unidirectional tires must always be mounted with arrow on tire sidewall pointing in direction of vehicle forward
movement. If the arrow on tire side wall does not point in direction of vehicle forward movement when using the spare
wheel, observe the following restrictions:

• Drive to the nearest tire repair facility as soon as possible.

For rim and tire specifications, refer to "Technical Data".

Warning !
The spare wheel rim is for temporary use only. Use for over a total of 12 000 miles
(20 000 km) may cause wheel rim failure leading to an accident and possible injuries.

Spare Wheel for Model C 43 AMG


The spare wheel rim size is 71/2 J x 17 H2
In the case of a flat tire or breakdown, you may temporarily use a 71/2 J x 17 H 2 instead of the
81/2 J x 17 H 2 wheel rim on the rear axle, when observing the following restrictions:
• Do not exceed vehicle speed of 50 mph (80 km/h).
• Drive to the nearest repair facility to have the flat tire repaired or replaced as appropriate.
For additional information, refer to "Technical Data".


Warning !

The dimensions of the spare wheel are different from those of road wheels. As a result, the
vehicle handling characteristics change when driving with a mounted spare wheel.
The spare wheel should only be used temporarily, and replaced with a regular road
wheel as quickly as possible.



1. Wheel bolt for model
C 43 AMG
2. Wheel bolt for model
C 230 Kompressor and C 280 with light alloy rims
3. Wheel bolt for Canada model
C 230 Kompressor with steel rims
Replace rims or tires with the same designation, manufacturer and type
as shown on the original part. See your authorized Mercedes-Benz
dealer for further information.

Warning !
The jack is designed exclusively for jacking up the vehicle at the jack tubes built into either side
of the vehicle. To help avoid personal injury, use the jack only to lift the vehicle during a wheel
change. Never get beneath the vehicle while it is supported by the jack. Keep hands and feet
away from the area under the lifted vehicle. Always firmly set parking brake and block wheels
before raising vehicle with jack. Do not disengage parking brake while the vehicle is raised. Be
certain that the jack is always vertical when in use, especially on hills. Always try to use the jack
on level surface. Be sure that the jack arm is fully inserted in the jack tube. Always lower the
vehicle onto sufficient capacity jackstands before working under the vehicle.

Changing Wheels

Move vehicle to a level area which is a safe distance from the road way.
1. Set parking brake and turn on hazard warning flasher.
2. Move selector lever to position "P" and turn off engine.
3. Prevent vehicle from rolling away by blocking wheels with wheel chocks
(not supplied with vehicle) or sizable wood block or stone. When changing a wheel
on a hill, place chocks on the downhill side blocking both wheels of the other axle.
On a level road, place one chock in front of and one behind the wheel that is
diagonally opposite to the wheel being changed.
4. Using the wrench, loosen but do not yet remove the wheel bolts.




5. Remove the protective cover from the jack support tube opening by inserting the
screwdriver (supplied in the tool kit) in the opening and prying it out. The tube
openings are located directly behind the front wheel housings and in front of the
rear
wheel housings.



6. Insert jack arm fully into the tube hole up to the stop.
Place jack on firm ground. Position the jack so that it is always vertical (plumb-line)
as seen from the side (see arrow), even if the vehicle is parked on an incline.
7. Jack up the vehicle until the wheel is clear of the ground.
Never start engine while vehicle is raised.
8. Unscrew upper-most wheel bolt and install alignment bolt (1) supplied in the
tool kit. Remove the remaining bolts. Keep bolt threads protected from dirt and
sand.



9. Remove wheel. Grip wheel from the sides. Keep hands from beneath the wheels.
10.Clean contact surfaces of wheel and wheel hub. Install spare wheel on wheel hub.
Insert wheel bolts and tighten them slightly. To avoid paint damage, place wheel
flat
against hub and hold it there while installing first wheel bolt.
Unscrew the alignment bolt (1) to install the last wheel bolt.
11.Lower car. Remove jack and insert jack tube cover.
Before storing the jack, the jack arm must be lowered almost to the base of the jack.



Warning !
Always replace wheel bolts that are damaged or rusted.
Never apply oil or grease to wheel bolts. Damaged wheel hub threads should
be repaired immediately.
Incorrect mounting bolts or improperly tightened mounting bolts can cause the
wheel to come off. This could cause an accident. Be sure to use the correct
mounting bolts.


12. Using the wrench, tighten the five bolts evenly, following the sequence illustrated,
until all bolts are tight. Observe a tightening torque of 80 ft.lb. (110 Nm).
13. Ensure proper tire pressure.

Tire Inflation Pressure
A table (see fuel filler flap) lists the tire inflation pressures specified for Mercedes-Benz recommended tires as well as
for the varying operating conditions.

Important !
Tire pressure changes by approx. 1.5 psi (0.1 bar) per 18°F (10°C) of air temperature change. Keep this in mind
when checking tire pressure inside a garage - especially in the winter.
Example:
If garage temperature = approx. +68°F (+20°C) and ambient te mperature = approx. +32°F (0°C) then the adjusted air
pressure = specified air pressure +3 psi (+0.2 bar).
Tire pressures listed for light loads are minimum values o ffering high driving comfort. Increased inflation pressures for
heavy loads produce favorable handling characteristics with lighter loads arid are perfectly permissible. The ride of
the vehicle, however, will become somewhat harder.
Tire temperature and pressure increase with the vehicle speed. Tire pressure should therefore only be corrected on
cold tires. Correct tire pressure in warm tires only if pressure has dropped below the pressure listed in the table and
the respective operating conditions are taken into consideration.
An underinflated tire due to a slow leak (e.g. due to a
nail in the tire) may cause damage such as tread separation, bulging etc.. Regular tire pressure checks (including the
spare tire) at intervals of no more than 14 days are therefore essential. If a tire constantly loses air, it should be
inspected for damage.

Warning !
Do not overinflate tires. Overinfiating tires can result in sudden deflation (blowout) because they are more
likely to become punctured or damaged by road debris, potholes etc.. Follow recommended inflation
pressures.
Do not overload the tires by exceeding the specified vehicle capacity weight (as indicated by the label on the
driver's door latch post). Overloading the tires can overheat them, possibly causing a blowout.

Technical Data C 230 KOMPRESSOR
Model C 230 KOMMPRESSOR
(202 024)1 Rims - Tires (except Sport Package)
Engine 111 Rims (light
alloy rims)

7J x 15 H 2
Mode of operation 4-stroke engine,
gasoline injection
Wheel offset 1.46 in (37 mm)
No. of cylinders 4

All season
tires:;
Radial-ply tires
205/60R 15 91 H
Bore 3.58 in (90.90 mm) Winter tires;
Radial-ply tires
205/60 R 15 91 T M+S
Stroke 3.48 in (88.40 mm) C 230 KOMMPRESSOR - Canada only (ikl.spare wheel)
Total piston displacemen 140.8 cu.in. (2295 cm3)

Rims (steel
rims)
Wheel offset

61/2J x 15 H 2
1.46 in (37 mm)

Compression ratio 8.8:1

All
season;Radial-
ply tires
Winter
tires;Radial-ply
tires

195/65 R 15 91 H
S

Output acc. to SAE J
1349
185 hp/5300 rpm
(136 kW/5300 rpm)
Rims All season Tires ( Sport Package)
Maximum torque acc.
to SAE J 1349
200 ft.lb./2500 rpm
(270 Nm/2500rpm)

Rims (light
alloy rims)
Wheel offset

7J x 16 H 2
1.46 in (37 mm)

Maximum engine speed 5800 rpm

All season
tires:
Radial-ply tires205/55 R 16 91 H
Firing order 1-3-4-2 Electrical System
tPoly-V-belt routing I 1875 mm Generator
(alternator)

14 V/90 A
Poly-V-belt routing II 1339 mm Starter motor 12 V/1.7KW
Weights See certification tag Battery 12 V/100 Ah
Roof load max.
Trunk load max.

220 lb(100 kg)
220 lb(100 kg)

Spark plugs
Electrode gap
Tightening
torque

Bosch F 7 KTCR
0.039 in (1,0 mm)
15-22ft.lb. (20-30 Mm)

Spare Wheel Main Dimensions
Rim (light alloy rim)
Wheel offset 7 J x 16 H 2
1.46 in (37 mm) Overall vehicle
length 178.2 in (4526 mm)
All season tire:
Radial-ply tire 205/55 R 16 91 H Overall vehicle
width 67.8 in (1723mm)
Overall height 56.1 in (1424 mm)
Spare Wheel ( exept Canada model with steel rims) Wheel base 105.9 in (2690 mm)
Rim (light alloy rim)
Wheel offset 7 J x 15 H 2
1.46 in (37 mm) Track, front 59.0 in (1499 mm)
All season tire:
Radial-ply tire 205/55 R 16 91 H Track, rear 57.6 in (1464mm)

1 The quoted data apply only to the standard vehicle. See an authorized Mercedes-Benz
dealer for the correspon-ding data of ali specialbodies and special equipment,