2000 MERCEDES-BENZ C-Class lamps

Exterior Lamp Switch
Off
Parking lamps (also side marker lamps, taillamps, license plate lamps, instrument panel lamps)
Canada only: When the engine is running, the low beam is additionally switched on.
Parking lamps plus low beam or high beam headlamps (combination switch pushed forward).
Standing lamps, right (turn left one stop).
Standing lamps, left (turn left two stops).
Front fog lamps (pull out one stop) with parking lamps and/or low beam headlamps on.
Rear fog lamp (pull out to 2nd detent) in addition to fog lamps. Yellow indicator lamp in lamp switch
comes on.

Standing Lamps
When the vehicle is parked on the street the standing lamps (right or left side parking lamps) can be turned on,
making the vehicle more visible to passing vehicles The standing lamps cannot be operated with the electronic key in
steering lock position 2.

Note:
With the electronic key removed and a front door open, a warning sounds if the vehicle's exterior lamps (except
standing lamps) are not switched off. Fog lamps will operate with the parking lamps and the low or high
beam headlamps Fog lamps should only be used in conjunction with low beam headlamps
Consult your State or Province Motor Vehicle Regulations regarding allowable lamp operation. Fog lamps are
automatically switched off when the exterior lamp switch is turned to position .


Daytime Running Lamps
Canada only

When the engine is running and the selector lever is in a driving position, the low beam (includes parking lamps,
side marker lamps, taillamps and license plate lamps) are automatically switched on.
When shifting from a driving position to position "N" or "P", the low beam switches off (2 seconds delay).

For nighttime driving the exterior lamp switch should be turned to position to permit activation of the high beam
headlamps.

Night Security Illumination

When exiting the vehicle after driving with the exterior lamps on, they switch on again for added illumination for
approximately 30 seconds after closing the last door. The lamp-on time period can be changed at your
Mercedes-Benz dealer.


Inside Rear View Mirror
Manually adjust the mirror.
Use your inside mirror to determine the size and distan ce of objects seen in the passenger side convex mirror.


Antiglare Night Position
With the electronic key in steering lock position 2, the mirror reflection brightness responds to changes in light
sensitivity. With gear selector lever in position "R", or with the interior lamp switched on, the mirror brightness
does not respond to changes in light sensitivity.

Note:
The automatic antiglare function is restricted, if incoming light is not aimed directly at sensors in the mirror.

Interior Lighting



1. Door contact switch:
Press once and interior lamps are switched on when opening a door. Interior lamps are switched on,
and off (soft fade) delayed, when unlocking or locking the vehicle, or when opening or closing a door.
However, there will be no (soft fade) delay when the electronic key is in steering lock position 2
Press again and interior lamps remain switched off, even when centrally unlocking or opening a door.
2. Press to switch interior and reading lamps on or off.
3. Press to switch rear passenger compartment lamp on or off.
4. Press to switch reading lamp on or off.



Parcel Net in Front Passenger Footwell
A small convenience parcel net is located in the front passenger footwell. It is for small and light items,
such as road maps, mail, etc..

Warning !
Do not place heavy or fragile objects, or objects having sharp edges, in the parcel net.
In an accident, during hard braking or sudden maneuvers, they could be thrown around
inside the vehicle, and cause injury to vehicle occupants.

Sliding/Pop-Up Roof (optional)

1. to slide roof open
2. to slide roof closed
3. to raise roof at rear
4. to lower roof at rear


Turn electronic key in steering lock to position 1 or 2. The switch is illuminated when the
exterior lamps are switched on (except standing lamps). With the roof closed or tilted open,
a screen can be slid into the roof opening to guard against sun rays. When sliding the roof
open, the screen will also retract.


Warning !
When closing the sliding/ pop-up roof, be sure that there
is no clanger of anyone being harmed by the closing
procedure. The closing procedure can be immediately
reversed by either moving the switch in direction
(1) or (3), turning the mechanical key to the unlocking
position, or pressing button on the remote control,
and holding it.
Notes:
The sliding/pop-up roof can be opened or closed manually should an electrical malfunction occur,
refer to Sliding/Pop-Up Roof, Emergency Operation in Index. The sliding/pop-up roof can also be
closed with the mechanical key or infrared remote control while locking the vehicle doors or trunk
(see Central Locking System in Index).


Synchronizing Sliding/Pop-Up Roof
If the power supply was interrupted (battery disconnected or empty), or if the sliding/pop-up roof is
blocked during closing/opening procedure, the system has to be synchronized. To do so, turn electronic
key in steering lock to position 2, move and hold switch in direction (3) until the sliding/pop-up roof is
completely raised at rear, and hold for additional 1 second.

Instrument Lamps
Press + or - button to vary intensity of instrument lamps.


Display illumination
The display for temperature, odometer, oil level indicator, FSS indicator and clock is illuminated briefly when opening
the
driver door. The display illumination brightness responds automatically according to changes in the surrounding light
sensitivity. To briefly illuminate the display (with electronic key removed or in steering lock position 0 or 1),
pressbutton
O, +,- , h or m.


Trip Odometer
• To reset:
• Press button O once and hold (with display illuminated).
• Press button O twice and hold (with display not illuminated).


Clock
Adjusting clock (display illuminated): Press button m or h briefly. The display flashes to indicate that the clock
can be adjusted.
Minute: Press button m briefly.
Minutes: Press and hold button m.
Hour: Press button h briefly.
Hours: Press and hold button h .

Antilock Brake System (ABS)

Important !
The ABS improves steering control of the vehicle during braking maneuvers. Do not pump the brake pedal, rather use
firm, steady brake pedal pressure. Pu mping the brake pedal defeats the pur pose for ABS and significantly reduces
braking effectiveness.
The ABS prevents the wheels from locking up above a vehicl e speed of approximately 5 mph (8 km/h) independent of
road surface conditions.
At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the
ABS is in the regulating mode. Keep firm and steady pressure on the brake pedal while experiencing the pulsation.
On slippery road surfaces, the ABS will re spond even with light brake pedal pressure because of the increased
likelihood of locking wheels. The pulsating brake pedal can be an indication of hazardous road conditions and
functions as a reminder to take extra care while driving.

ABS Control
The ABS malfunction indicator lamp in the instrument cl uster comes on with the electronic key in steering lock
position 2 and should go out when the engine is running.
If the charging voltage falls below 10 volts, the malfunction indicator lamp comes on and the ABS is switched off.
When the voltage is above this value again, the malfunction indicator lamp should go out and the ABS is operational.
With the ABS malfunctioning, the ASR or ESP, if vehicl e so equipped, are also switched off. Both malfunction
indicator lamps come on with the engine running. If the ABS malfunction indicator lamp does not go out or comes on
while driving, it indicates that the ABS has detected a malfunction and has switched off. In this case, the brake
system functions in the usual manner, but without antilock assistance.
Have the system checked at your authorized Mercedes-Benz dealer as soon as possible.

Warning !
ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction
made available by the road conditions. The ABS ca nnot prevent accidents, including those resulting from
excessive speed in turns, following another vehicle too cl osely, or aquaplaning. Only a safe, attentive, and
skillful driver can prevent accidents. The capabilities of an ABS equipped car must never be exploited in a
reckless or dangerous manner which could jeopardize the user's safety or the safety of others.

Note:
To alert following vehicles to slippery road conditions you discover, operate your hazard warning flashers as
appropriate.

Brake Assist System (BAS)

Warning !

BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking
efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following
another vehicle too closely, or aquaplaning. Only a safe, attentive, and skillful driver can prevent accidents.
The capabilities of a BAS equipped car must never be exploited in a reckless or dangerous manner which
could jeopardize the user's safety or the safety of others.

The Brake Assist System is designed to maximize the vehicle's braking capability during emergency braking
maneuvers by having maximum power boost applied to the br akes more quickly in emergency braking conditions
than might otherwise be afforded solely by the driver's braking style. This can help reduce braking distances over
what ordinary driving and braking style might do. The BAS complements the Antilock Brake System (ABS).
To receive the benefit of the system you must apply continuous full braking power during the stopping sequence.
Do not reduce brake pedal pressure.
Once the brake pedal is released, the BAS is deactivat ed The malfunction indicator lamps for the ASR and ESP are
combined with the BAS malfunction indicator lamp.
The BAS/ASR or BAS/ESP malfunction indicator lamp in the instrument cluster come on with the electronic key in
steering lock position 2 and should go out with the engine running.
If the BAS/ASR or BAS/ESP malfunction indicator lamp comes on permanently while the engine is running,
a malfunction has been detected in either system. As a resul t, it is possible that now only partial engine output will be
available, and pressing the accelerator pedal will require more effort. If the BAS malfunctions. The brake system
functions in the usual manner, but wi thout BAS. If the charging voltage falls be low 10 volts, the malfunction indicator
lamp comes on and the BAS is switched off. When the volt age is above this value again, the malfunction indicator
lamp should go out and the BAS is operational. With t he ABS malfunctioning, the BAS, ASR or ESP are also
switched off.
Both malfunction indicator lamps come on with the engine running. Have the BAS, ASR or ESP checked at your
authorized Mercedes-Benz dealer as soon as possible .

Exterior Lamps
Headlamp Adjustment

Correct headlamp adjustment is extremely important. Check and readjust headlamps at regular intervals and
when a bulb has been replaced.




Headlamp Assembly
1. Cover for low beam headlamp bulb, fog lamp, and level for vertical adjustment
2. Latch for cover (1)
3. Cover for high beam headlamp bulb
4. Clamp for cover (3)
5. Headlamp vertical adjustment screw

6. Headlamp horizontal adjustment screw
7. Scale for horizontal adjustment
8. Electrical connector for low beam headlamp bulb
9. Electrical connector for fog lamp bulb
10.Electrical connector for high beam headlamp bulb



Replacing Bulb:
To prevent a possible electrical short circuit, switch off lamp prior to replacing a bulb. When replacing bulbs,
install only 12 volt bulbs with the specified watt rating. When replacing halogen bulbs do not touch glass
portion of bulb with bare hands. Use plain paper or a clean cloth.

Warning !
Halogen lamps contain pressurized gas. A bulb can explode if you:
• touch or move it when hot,
• drop the bulb,
• scratch the bulb.
Wear eye and hand protection.

Bulb for Low Beam H7 (55 W) Bulb for Fog Lamp H1 (55 W)

Open hood.
Depress latch (2) and remove cover (1). Pull of electrical connector (8) or (9). Unhook clamping ring and
removes bulb. Insert new bulb (seating properly in cutouts of bulb socket), and mount clamping ring.
Reinstall and push electrical connector on securely. Reinstall bottom end of cover (1) and push against top
end of cover until properly seated. Check lamp for proper operation.

Xenon (optional)
Bulb for Low Beam

Warning !
Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its
components. We recommend that you have such work done by a qualified technician.