2000 Lexus LS400 rear view mirror

COMFORT ADJUSTMENT
138
Power rear view mirror control
16L017-2

1Master switch 2Control switch
To adjust the power rear view mirror, first place the
master switch at ºLº (left) or ºRº (right), and push
the control switch on the desired side.
The power rear view mirror can be adjusted when the
key is in the ºACCº or ºONº position.

COMFORT ADJUSTMENT
140
Folding rear view mirrors
16L018
To fold the rear view mirror, push backward.
The rear view mirrors can be folded backward for
parking in restricted areas.
CAUTION
Do not drive with the mirrors folded backward. Both the
driver and passenger side rear view mirrors must be
extended and properly adjusted before driving.

COMFORT ADJUSTMENT
141
INSIDE REAR VIEW MIRROR
16L019-1

COMFORT ADJUSTMENT
142Adjust the m
irror so that you can just see the rear of
your vehicle in the mirror.
Pushing the switch changes the mode between
ºAUTOº and ºDAYº.
The indicator comes on when the ºAUTOº mode is
selected.
ºDAYº mode: The mirror surface is normal.
ºAUTOº mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror
surface darkens slightly to reduce the reflected
light.
When the inside rear view mirror surface changes, the
outside rear view mirror surfaces will also become
darker.
When the ignition key is inserted and turned on, the
inside rear view mirror always turns on in the ºAUTOº
mode. When the outside air temperature is low, it may take a
little longer for the mirror to darken in response to the
detection of headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving. It
may cause the driver to mishandle the vehicle and an
accident may occur resulting in personal injuries.

COMFORT ADJUSTMENT
210
DRIVING POSITION MEMORYSYSTEM
The micro computer can memorize the position of the
driver's seat, the height of the shoulder belt anchor of the
driver's seat belt, and the positions of the tilt and
telescopic steering, and outside rear view mirrors. Two
different driving position profiles can be entered into the
computer's memory.
Recording a driving position in the computer's memory
can only be done when the ignition key is in the ºONº
position and the selector lever is in the ªNº or ªPº position.
Setting a driving position
16L055

COMFORT ADJUSTMENT
211
1. Adjust the driver's seat, driver's shoulder belt
anchor,
tilt and telescopic steering and outside rear
view mirrors to the desired position.
2. While pushing the ºSETº button, push button º1º
or º2º until the signal beeps.
The beep sound means that the positions are recorded
in the computer's memory.
By repeating these two steps and pressing the
remaining button, the driving position for another driver
can be recorded.
To set a new memorized position, select the desired
position and perform step 2. The previous memory will
be erased and the new position will be set.
To make only slight changes to an already memorized
position, the easiest way is to first activate the
memorized position, then make the desired changes
and perform step 2 above.

STARTING AND DRIVING
283
Keep the trunk lid closed while driving. An
open or unsealed trunk lid may cause exhaust
gases to be drawn into the vehicle.
 To allow proper operation of your vehicle's
ventilation system, keep the inlet grilles in front
of the windshield clear of snow, leaves, or other
obstructions.
 If you smell exhaust fumes in the vehicle, drive
with the windows open and the trunk lid closed.
Have the cause immediately located and
corrected.BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint
height and steering wheel angle.
3. Adjust the inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to ºONº, and check the fuel
gauge to see that you have sufficient fuel.

STARTING AND DRIVING
299
(d) Backing up
31L012a

1ºRº (Reverse) position 2Brake pedal
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift
the selector lever to the ºRº position.
NOTICE
Never shift into reverse while the vehicle ismoving.
When you are backing up, you can adjust the outside
rear view mirror on the passenger's side down quickly.
For details, see page 138.