2000 LEXUS GS400 light

PP0O2±02
± PREPARATIONBODY ELECTRICAL
PP±93
145 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerEngine coolant temperature sender gauge, Engine oil level warn-
ing switch, Seat heater
SyphonBrake fluid level warning switch
Oil bathEngine oil level warning switch
Bulb (1.4 W)Defogger switch
Bulb (3.4 W)Fuel sender gauge, Engine coolant temperature receiver gauge,
Seat belt warning relay
Dry cell batteryFuel sender gauge, Power mirror
Heat lightSeat heater
Hexagon wrench (6 mm)Power seat
Torque wrench
Clip removerFor removing cowl louver
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

SS0CN±02
SS±60
± SERVICE SPECIFICATIONSBODY ELECTRICAL
216 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
BODY ELECTRICAL
SERVICE DATA
DAYTIME RUNNING LIGHT RELAY (MAIN) (Wire Harness Side)
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON or START)Battery positive voltage
5 ± Ground (Engine Stop)No voltage
5 ± Ground (Engine Running)Battery positive voltage
7 ± Ground (Constant)Battery positive voltage
9 ± Ground (Constant)Battery positive voltage
AUTOMATIC LIGHT CONTROL SENSOR
(Connector disconnected)
4 ± Ground (Ignition switch position LOCK or ACC)No voltage
4 ± Ground (Ignition switch position ON)5.2 ± 9.0 V
(Connector connected)
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON)9.5 V or more
HEADLIGHT BEAM LEVEL CONTROL ECU
(Connector disconnected)
A1 ± A5 (Ignition switch position OFF)26 ± 30 W
A1 ± A6 (Ignition switch position OFF)26 ± 30 W
A1 ± A7 (Ignition switch position OFF)26 ± 30 W
A1 ± A8 (Ignition switch position OFF)26 ± 30 W
A4 ± B4 (Ignition switch position ON and light control switch HEAD)Below 1.5 V
B1 ± B3 (Ignition switch position OFF)3.5 k ± 6.5 kW
B5 ± B7 (Ignition switch position OFF)3.5 k ± 6.5 kW
(Connector disconnected)
B2 ± B3 (Ignition switch position ON)Approx. 2.5 V
B6 ± B7 (Ignition switch position ON)Approx. 2.5 V
B1 ± B3 (Ignition switch position ON)5V
B5 ± B7 (Ignition switch position ON)5V
TURN SIGNAL FLASHER
1 ± Ground (Ignition switch position LOCK or ACC)No voltage
1 ± Ground (Ignition switch position ON)Battery positive voltage
4 ± Ground (Constant)Battery positive voltage
LIGHT FAILURE RELAY (Wire Harness Side)
5 ± Ground (Light control switch position OFF)No voltage
5 ± Ground (Light control switch position TAIL or HEAD)Battery positive voltage
8 ± Ground (Ignition switch position LOCK or ACC)No voltage
8 ± Ground (Ignition switch position ON)Battery positive voltage
9 ± Ground (Stop light switch position OFF)No voltage
9 ± Ground (Stop light switch position ON)Battery positive voltage
10 ± Ground (Stop light switch position OFF)No voltage
10 ± Ground (Stop light switch position ON)Battery positive voltage
SPEEDOMETER (ON±VEHICLE)
USA:

SF0N1±03
± SFI (2JZ±GE)SFI SYSTEM
SF±1
1467 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
SFI SYSTEM
PRECAUTION
1. BEFORE WORKING ON FUEL SYSTEM, DISCON-
NECT NEGATIVE (±) TERMINAL CABLE FROM BAT-
TERY
HINT:
Any diagnostic trouble code retained by the ECM will be erased
when the battery negative (±) terminal cable is removed from
the battery.
Therefore, if necessary, read the diagnostic trouble code(s) be-
fore removing the negative (±) terminal cable from the battery.
2. DO NOT SMOKE OR WORK NEAR AN OPEN FLAME
WHEN WORKING ON FUEL SYSTEM
3. KEEP GASOLINE AWAY FROM RUBBER OR LEATH-
ER PARTS
4. MAINTENANCE PRECAUTIONS
(a) Precaution when the connecting gauge.
Use battery as the power source for the timing light, etc.
(b) In the event of engine misfire, these precautions should
be taken.
(1) Check proper connection of battery terminals, etc.
(2) Handle high±tension cords carefully.
(3) After repair work, check that the ignition coil termi-
nals and all other ignition system lines are recon-
nected securely.
(4) When cleaning the engine compartment, be espe-
cially careful to protect the electrical system from
water.
(c) Precautions when the handling heated oxygen sensors.
(1) Do not allow oxygen sensor to drop or hit against an
object.
(2) Do not allow the sensor to come into contact with
water.
5. IF VEHICLE IS EQUIPPED WITH MOBILE RADIO SYS-
TEM (HAM, CB, ETC.)
If the vehicle is equipped with a mobile communication system,
refer to the precaution in the IN section.
6. AIR INDUCTION SYSTEM
(a) Separation of the engine oil dipstick, oil filler cap, PCV
hose, etc. may cause the engine to run out of tune.
(b) Disconnection, looseness or cracks in the parts of the air
induction system between the throttle body and cylinder
head will cause air suction and cause the engine to run
out of tune.

FI2553
SST
SF±2
± SFI (2JZ±GE)SFI SYSTEM
1468 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. ELECTRONIC CONTROL SYSTEM
(a) Before removing SFI wiring connectors, terminals, etc.,
first disconnect the power by either turning the ignition
switch OFF or disconnecting the negative (±) terminal
cable from the battery.
HINT:
Always check the diagnostic trouble code before disconnecting
the negative (±) terminal cable from the battery.
(b) When installing the battery, be especially careful not to in-
correctly connect the positive (+) and negative (±) cable
terminals.
(c) Do not permit parts to receive a severe impact during re-
moval or installation. Handle all SFI parts carefully, espe-
cially the ECM.
(d) Do not be careless during troubleshooting as there are
numerous transistor circuits and even slight terminal con-
tact can further troubles.
(e) Do not open the ECM cover.
(f) When inspecting during rainy weather, take care to pre-
vent entry of water. Also, when washing the engine
compartment, prevent water from getting on the SFI parts
and wiring connectors.
(g) Parts should be replaced as an assembly.
(h) Care is required when pulling out and inserting wiring con-
nectors.
(1) Release the lock and pull out the connector, pulling
on the connectors.
(2) Fully insert the connector and check that it is locked.
(i) When inspecting a connector with a volt/ohmmeter.
(1) Carefully take out the water±proofing rubber if it is
a water±proof type connector.
(2) Insert the test probe into the connector from wiring
side when checking the continuity, amperage or
voltage.
(3) Do not apply unnecessary force to the terminal.
(4) After checking, install the water±proofing rubber on
the connector securely.
(5) Use SST for inspection or test of the injector or its
wiring connector.
SST 09842±30070

B01875
Fuel
Pump
Connector
B01998
New
Gasket
New
Gasket
FI1654
SST
Fulcrum Length
30 cm
± SFI (2JZ±GE)SFI SYSTEM
SF±3
1469 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
8. FUEL SYSTEM
(a) When disconnecting the high pressure fuel line, a large
amount of gasoline will spill out, so observe these proce-
dures:
(1) Disconnect the fuel pump connector.
(2) Start the engine. After the engine has stopped on
its own, turn the ignition switch OFF.
(3) Put a container under the connection.
(4) Slowly loosen the connection.
(5) Disconnect the connection.
(6) Plug the connection with a rubber plug.
(7) Reconnect the fuel pump connector.
(b) When connecting the flare nut or union bolt on the high
pressure pipe union, observe these procedures:
(1) Union Bolt Type:
Always use a new gasket.
(2) Union Bolt Type:
Tighten the union bolt by hand.
(3) Union Bolt Type:
Tighten the union bolt to the specified torque.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
(4) Flare Nut Type:
Apply a light coat of engine oil to the flare and tight-
en the flare nut by hand.
(5) Flare Nut Type:
Using SST, tighten the flare nut to the specified
torque.
SST 09631±22020
NOTICE:
Do not rotate the fuel pipe, when tightening the flare nut.
Torque:
30 N´m (310 kgf´cm, 22 ft´lbf) for using SST
38 N´m (387 kgf´cm, 28 ft´lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

SF0N5±02
B02037
Push
B01892
Fuel Port Hole
No.1 Fuel Filter
Cushion
Fuel Port
New O±Ring
B01893
B02038
Snap Claw
Push
B01887
New Clip
± SFI (2JZ±GE)FUEL PUMP
SF±13
1479 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL FUEL PUMP TO FUEL FILTER
Push in the fuel pump.
2. INSTALL FUEL FILTER AND FUEL PUMP ASSEMBLY
(a) Install the No.1 fuel filter cushion to the fuel suction plate.
(b) Apply a light coat of gasoline to a new O±ring and install
it to the fuel port of the fuel suction plate.
(c) Align the fuel port of the fuel suction plate with the fuel port
hole of the fuel filter.
(d) Push in the fuel filter.
(e) Connect the fuel pump connector.
3. INSTALL NO.1 FUEL SUCTION SUPPORT
(a) Install the No.2 fuel filter cushion to the fuel filter.
(b) Push the fuel suction support, and attach the 4 snap
claws to the claw holes.
4. INSTALL FUEL SUCTION FILTER
Install the suction filter with a new clip.
5. INSTALL FUEL PRESSURE REGULATOR AND FUEL
RETURN JET TUBE ASSEMBLY (See page SF±18)
6. INSTALL NO.2 FUEL SUCTION SUPPORT
(See page SF±18)

SF0N8±01
B02061
Connect
Push
B01885
B02039Push
Snap Claw
SF±18
± SFI (2JZ±GE)FUEL PRESSURE REGULATOR
1484 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL FUEL PRESSURE REGULATOR AND FUEL
RETURN JET TUBE ASSEMBLY
(a) Apply a light coat of gasoline to a new O±ring, and install
it to the fuel pressure regulator.
(b) Push in the fuel pressure regulator to the fuel filter.
(c) Check that the fuel pressure regulator rotates smoothly.
If it does not rotates smoothly, the O±ring may be pinched, so
remove the fuel pressure regulator and perform again steps (b)
and (c) above.
(d) Connect the fuel return jet tube to the clamp of the No.2
fuel suction support.
2. INSTALL NO.2 FUEL SUCTION SUPPORT
(a) Install the rubber cushion to the fuel pump.
(b) Push the fuel suction support, and attach the 4 snap
claws to the claw holes.
3. INSTALL FUEL PUMP AND SENDER GAUGE AS-
SEMBLY TO FUEL TANK (See page SF±13)

SF0ND±04
B01220
New Insulator
New O±Ring
New Grommet New O±Ring
B01571
Turn
Outward
Connector
B01580
RotateUpward SF±24
± SFI (2JZ±GE)INJECTOR
1490 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
INSTALLATION
1. INSTALL INJECTORS AND DELIVERY PIPE
(a) Install new insulator and grommet to each injector.
(b) Apply a light coat of spindle oil or gasoline to 2 new O±
rings and install them to each injector.
(c) Apply a light coat of spindle oil or gasoline on the place
where a delivery pipe touches an O±ring of the injector.
(d) While turning the injector clockwise and counterclock-
wise, push it to the delivery pipe. Install the 6 injectors.
(e) Position the injector connector outward.
(f) Place the 3 spacers in position on the intake manifold.
(g) Apply a light coat of spindle oil or gasoline on the place
where a intake manifold touches an O±ring of the injector.
(h) Place the 6 injectors together with the delivery pipe and
3 bolts in position on the intake manifold.
(i) Temporarily install the 3 bolts holding the delivery pipe to
the intake manifold.
(j) Check that the injectors rotate smoothly.
HINT:
If injectors do not rotate smoothly, the probable cause is incor-
rect installation of O±rings. Replace the O±rings.
(k) Position the injector connector upward.
(l) Connect the 6 injector connectors.
HINT:
The Nos.1, 3, 5 injector connectors and dark gray, and the
Nos.2, 4, 6 injector connectors are brown.
(m) Tighten the 3 bolts holding the delivery pipe to the intake
manifold.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(n) Connect the camshaft position sensor connector.
(o) Connect the throttle position sensor connector.
(p) Connect the VSV connector for EVAP.
2. INSTALL FUEL PRESSURE PULSATION DAMPER
(See page SF±27)
3. INSTALL AIR INTAKE CHAMBER
(See page SF±49)
4. INSTALL ENGINE COVER
Install the engine cover with the 4 nuts.