Page 77 of 501
GAUGES, METERS AND SERVICE REMINDER INDICATORS
57
Your vehicle may overheat during severe operating
conditions, such as:
Driving up a long hill on a hot day.
Reducing speed or stopping after high speed driving.
Idling for a long period with the air conditioning on in
stop±and±go traffic.
Towing a trailer.
NOTICE
Do not remove the thermostat in the engine
cooling system as this may cause the engine to
overheat. The thermostat is designed to control the flow of coolant to keep thetemperature of the engine within the specifiedoperating range.
Do not continue driving with an overheatedengine. See ªIf your vehicle overheatsº onpage 342.
Page 293 of 501
STARTING AND DRIVING
273
NOTICEA large amount of unburned gases flowing intothe three±way catalytic converter may cause it tooverheat and create a fire hazard. To prevent this
and other damage, observe the following precautions:
Use only unleaded gasoline.
Do not drive with an extremely low fuel level;running out of fuel could cause the engine tomisfire, creating an excessive load on thethree±way catalytic converter.
Do not allow the engine to run at idle speed formore than 20 minutes.
Avoid racing the engine.
Do not push±start or pull±start your vehicle.
Do not turn off the ignition while the vehicle ismoving.
Keep your engine in good running order.Malfunctions in the engine electrical system,electronic ignition system/distributor ignitionsystem or fuel system could cause anextremely high three±way catalytic converter
temperature.
If the engine becomes difficult to start or stallsfrequently, take your vehicle in for a check±upas soon as possible. Remember, your Lexusdealer knows your vehicle and its three±waycatalytic converter system best.
Page 301 of 501
STARTING AND DRIVING
281
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in ªPº. If you need to restart the
engine while the vehicle is moving, put the selector lever
in ªNº. A starter safety device will prevent the starter
from operating if the selector lever is in any drive
position.
4. Depress the brake pedal and hold it to the floor until
driving off.
Starting the engine
Before starting the engine, be sure to follow the
instructions in ªBefore crankingº.
Normal starting procedure
The multiport fuel injection system/sequential multiport
fuel injection system in your engine automatically
controls the proper air±fuel mixture for starting. You can
start a cold or hot engine as follows:
1. With your foot off the accelerator pedal, crank the
engine by turning the key to ªSTARTº. Release it when
the engine starts.
2. After the engine runs for about 10 seconds, you are
ready to drive. If the weather is below freezing, let the engine warm up
for a few minutes before driving. Do not leave the vehicle
while the engine is warming up.
If the engine stalls ...
Simply restart it , using the correct procedure given in
normal starting.
If the engine will not start
See ªIf your vehicle will not startº on page 337.
NOTICE
Do not crank for more than 30 seconds at a
time. This may overheat the starter and wiringsystems.
Do not race a cold engine.
If the engine becomes difficult to start or stallsfrequently, have the engine checkedimmediately.
Page 310 of 501
STARTING AND DRIVING
290
(d) Using the ª2º and ªLº positions
The ª2º and ªLº positions are used for strong engine
braking as described previously.
With the selector lever in ª2º or ªLº, you can start the
vehicle in motion as with the lever in ªDº.
With the selector lever in ª2º, the vehicle will start in the
first gear and automatically shift to second gear.
With the selector lever in ªLº, the transmission is
engaged in first gear.
NOTICE
Be careful not to overrev the engine. Watch thetachometer to keep engine rpm from going intothe red zone. The approximate maximumallowable speed for each position is givenabove for your reference.
ª2º 128 km/h (80 mph) . . .
ªLº 71 km/h (44 mph) . . .
Do not continue hill climbing or hard towing for
a long time in the ª2º or ªLº position. This maycause severe automatic transmission damagefrom overheating. To prevent such damage,
ªDº position should be used in hill climbing orhard towing.
Page 313 of 501
STARTING AND DRIVING
293
(g) Good driving practice
If the transmission repeatedly shifts up and down
between the third and overdrive gears when climbing
a gentle slope, the overdrive should be turned off. Be
sure to turn the switch on immediately after climbing
the slope.
When towing a trailer, in order to maintain efficient
engine braking and electrical charging performance,
do not use overdrive.
CAUTION
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE
Do not hold the vehicle on an upgrade with the accelerator pedal. This can cause thetransmission to overheat. Always use the brakepedal or parking brake.
(h) Rocking your vehicle if stuck
CAUTION
If your vehicle becomes stuck in snow, mud, sand, etc.,
then you may attempt to rock the vehicle free by moving
it forward and backward. Do not attempt this procedure
if people or objects are anywhere near the vehicle.
During the rocking operation the vehicle may suddenly
move forward or backward as it becomes un±stuck,
causing injury or damage to nearby people or objects.
Page 338 of 501
DRIVING TIPS
318
CAUTION
Before driving off, make sure the parking brake is
fully released and that the parking brake reminder
light is off.
Do not rest your foot on the brake pedal while driving.
It can cause dangerous overheating, needless wear,
and poor fuel economy.
To drive down a long or steep hill, reduce your speed
and downshift. Remember, if you ride the brakes
excessively, they may overheat and not work
properly. See page 288.
Be careful when accelerating, upshifting,
downshifting or braking on a slippery surface. The
abrupt change in engine speed, such as sudden
acceleration or engine braking, could cause the
vehicle to spin or skid.
Do not drive in excess of the speed limit. Even if the
legal speed limit permits it, do not drive over 140 km/h
(85 mph) unless your vehicle has high±speed
capability tires. Driving over 140 km/h (85 mph) may
result in tire failure, loss of control and possible
injury. Be sure to consult a tire dealer to determine
whether the tires on your vehicle are high±speed
capability tires or not before driving at such speeds.
Page 349 of 501
DRIVING TIPS
329
wheels will be closer than the vehicle wheels to the
inside of the turn. Therefore, compensate for this by
making a larger than normal turning radius with your
vehicle.
Crosswinds and rough roads will adversely affect
handling of your vehicle and trailer, causing sway.
Pay attention to the rear from time to time to prepare
yourself for being passed by large trucks or buses,
which may cause your vehicle and trailer to sway. If
swaying happens, firmly grip the steering wheel and
reduce speed immediately but gradually. Never
increase speed. If it is necessary to reduce speed,
brake slowly. Steer straight ahead. If you make no
extreme correction with the steering or brakes, your
vehicle and trailer will stabilize.
Be careful when passing other vehicles. Passing
requires considerable distance. After passing a
vehicle, do not forget the l ength of your trailer and be
sure you have plenty of room before changing lanes.
In order to maintain efficient engine braking and
electrical charging performance, do not use
overdrive.
Because of the added load of the trailer, your vehicle's
engine may overheat on hot days (at temperatures
over 30C [85F]) when going up a long or steep
grade with a trailer. If the engine coolant temperature
gauge indicates overheating, immediately turn off the
air conditioning (if in use), pull your vehicle off the
road and stop in a safe spot. See ªIf your vehicle
overheatsº on page 342 of this manual.
Always place wheel blocks under both the vehicle
and trailer wheels when parking. Apply the parking
brake firmly. Put the transmission in ªPº. Avoid
Page 353 of 501
DRIVING TIPS
333
Avoid continuous speeding up and slowing
down. Stop±and±go driving wastes fuel.
Avoid unnecessary stopping and braking.
Maintain a steady pace. Try to time the traffic si gnals
so you only need to stop as little as possible or take
advantage of through streets to avoid traffic lights.
Keep a proper distance from other vehicles to avoid
sudden braking. This will also reduce wear on your
brakes.
Avoid heavy traffic or traffic jams whenever
possible.
Do not rest your foot on the brake pedal. This
causes premature wear, overheating and poor fuel
economy.
Maintain a moderate speed on highways. The
faster you drive, the greater the fuel consumption. By
reducing your speed, you will cut down on fuel
consumption.
Keep the front wheels in proper alignment. Avoid
hitting the curb and slow down on rough roads.
Improper alignment not only causes faster tire wear
but also puts an extra load on the engine, which, in
turn, wastes fuel.
Keep the bottom of your vehicle free from mud
etc. This not only lessens weight but also helps
prevent corrosion.
Keep your vehicle tuned±up and in top shape. A
dirty air cleaner, improper valve clearance, dirty
plugs, dirty oil and grease, brakes not adjusted, etc.
all lower engine performance and contribute to poor
fuel economy. For longer life of all parts and lower
operating costs, keep all maintenance work on
schedule, and if you often drive under severe
conditions, see that your vehicle receives more
frequent maintenance. (For scheduled maintenance
information, please refer to the ªOwner's Manual
Supplement/Maintenance Scheduleº.)
