2000 Lexus ES300 tow

INTRODUCTION
388
NOTICE

Remember that battery and ignition cablescarry high currents or voltages. Be careful ofaccidentally causing a short circuit.

Before closing the engine hood, check to seethat you have not forgotten any tools, rags, etc.

Do not drive with the air cleaner removed, or
excessive engine wear could result. Alsobackfiring could cause a fire in the enginecompartment.

Do not overfill automatic transmission fluid, orthe transmission could be damaged.

Be careful not to scratch the glass surface withthe wiper frame.
PARTS AND TOOLS
Here is a list of parts and tools you will need to perform
do±it±yourself maintenance. Remember all Lexus parts
are designed in metric sizes, so your tools must be
metric.
Checking the engine oil level
Parts (if level is low):

Use API grade SJ, ªEnergy±Conservingº multigrade
engine oil or ILSAC multigrade engine oil. For
recommended oil viscosity, see page 406.
Tools:

Rag or paper towel

Funnel (only for adding oil)
Checking the engine coolant level
Parts (if level is low):

ªTOYOTA Long Life Coolantº or equivalent
See ªChecking the engine coolant levelº on page 407
for instructions.

Demineralized or distilled water
Tools:

Funnel (only for adding coolant)

INTRODUCTION
389
Checking brake fluid
Parts (if level is low):

FMVSS No. 116 DOT 3 or SAE J1703 brake fluid
Tools:

Funnel (only for adding fluid)
Checking power steering fluid
Parts (if level is low):

Automatic transmission fluid DEXRON
II or III
Tools:

Rag or paper towel

Funnel (only for adding fluid)
Checking battery condition
Non±maintenance batteries
Tools:

Warm water

Baking soda

Grease

Conventional wrench (for terminal clamp bolts)
Maintenance type batteries
Parts (if level is low):

Distilled water
Tools:

Warm water

Baking soda

Grease

Conventional wrench (for terminal clamp bolts)

Coin (for vent plugs)

Funnel (only for adding distilled water)

CHASSIS
415
± TIRES AND WHEELS
Tire size
Recommended cold tire inflation pressure Vehicle load up to 4 occupants
Vehicle loaded up to vehicle capacity weight
Spare tire
Trailer towing (conventional and snow tires)
Wheel size
Wheel nut torque
Type A: P205/65R15 92V
Type B: P205/60R16 91V
180 kPa (1.8 kgf/cm
2 or bar, 26 psi) (Both front and
rear)
220 kPa (2.2 kgf/cm
2 or bar, 32 psi) (Both front and
rear)
220 kPa (2.2 kgf/cm
2 or bar, 32 psi)
220 kPa (2.2 kgf/cm2 or bar, 32 psi) (Both front and
rear)
Type A: 15
6 JJ
Type B: 16
6 JJ
103 N´m (10.5 kgf´m, 76 ft´lbf.)
NOTE: For a complete information on tires (e.g. replacing tires or replacing \
wheels), see ªChecking tire pressureº
through ªAluminum wheel precautionsº on page 423 through 432.

BODY
475
Plastic wheel ornaments:
The plastic wheel
ornaments are damaged easily by organic substances.
If any organic substances splashes an ornament, be
sure to wash it off with water and check if the ornament
is damaged.
CAUTION
Do not attach the heavily damaged plastic wheel
ornament. It may fly off the wheel and cause accidents
while the vehicle is moving.
Aluminum wheels: Use only a mild soap or neutral
detergent.
Urethane bumpers and side moldings: Wash
carefully. Do not scrub with abrasive cleaners. The
bumper and side molding faces are soft.
Road tar: Remove with turpentine or cleaners that are
marked safe for painted surfaces.
NOTICE
Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may
be toxic or cause damage.
3. Rinse thoroughly ± dried soap can cause streaking.
In hot weather you may need to rinse each section right
after you wash it. 4. To prevent water spots, dry the vehicle using a clean
soft cotton towel. Do not rub or press hard ± you might
scratch the paint.
Automatic car wash
Your vehicle may be washed in an automatic car wash,
but remember that the paint can be scratched by some
type of brushes, unfiltered washing water, or the
washing process itself. Scratching reduces paint
durability and gloss, especially on darker colors. The
manager of the car wash should be able to advise you
whether
the process is safe for the paint on your vehicle.